Department Of Atomic Energy Tender
... More
If you're looking for Rajasthan tenders online and are tired of typing tender ID over and again or going through the cumbersome government websites for it, you are in luck. We have collated every Eproc Rajasthan tender on BidAssist. And for any queries related to an e-tender Rajasthan, like bidding process, registration process, etc., are explained below. Read on.
Department Of Atomic Energy - DAE Tender
Civil And Construction
Pipe Line Project
Eprocure
Opening Date13 Dec 2024
Closing Date30 Dec 2024
Tender Amount₹ 68,56,766
Costs
EMD
₹ 1,37,135Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_HWB_839411_1Bid Award Id
ViewTender No
HWPK/MECH/2024/427Tender Authority
Department Of Atomic Energy ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
stainless steel piping welding (TIG welding with argon gas purging using AWS ER 316L for root & subsequent stablising passes,then remaining to be welded with TIG without purging ) including bevel edge preparation,LPT as per HWPK piping specification and guide lines of engineer incharge.
-
-
-
... More
SW/FW upto Sch XS
350
-
-
... More
Butt Weld upto Sch XS
700
-
-
... More
Carbon steel piping welding (SMAW welding using AWS E-7018-1 electrode for root & all subsequent passes) including bevel edge preparation,LPT as per HWPK piping specification and guide lines of engineer incharge.
-
-
-
... More
SW/FW upto Sch 80
1800
-
-
... More
Butt Weld upto Sch 80
3100
-
-
... More
Erection of CS/SS welded pipes along with its fittings, flanges, valves, SRV's, rupture disc, carrying out flange jointing and torquing, u clamps, anchors, pipe hangers, etc.
8000
-
-
... More
Removal of existing installed pipes from their position by gas cutting, grinding m/c etc :-Existing pipeline to be cut and removed by grinding/ gas cutting and shifting of same to desginated place/HWPK stores as per guideline of engineer In Charge .
8000
-
-
... More
Fabrication, welding and erection of structural steel platforms/sliding supports/support clamps with structural sections/plates/gratings, structural steel required for the job shall be supplied by department & to be fabricated by contractor as per site conditions in guidelines of the HWPK engineer.
3
-
-
... More
Radiography of the weld joint with gamma ray source as per ASME code section III :-For carrying out radiography work, contractor should arrange Gamma ray source of proper capacity. Arrange for punching segment mark on the pipeline nearer the weld joint arrange source and film positioner, taking exposed film and developing it, drying the film and submission to HWPK engineer. Film to be used for this purpose shall be NDT - 65 or its equivalent. They should also cordon the area whereradiography is to be taken with necessary caution display board.
3000
-
-
... More
Stress relieving of the welded joints by resistance heating up to 610 degree centrigrade after radiographic examination. The chart of stress relieving shall be submitted to Engineer In charge.
2700
-
-
... More
Weld build up inside tanks,valve bodies and flange areas at various locations as marked by engineers incharge. the job includes following works :-(1).cleaning of area with Wire brush/grinder.(3)Root pass and Subsequent pass welding with GTAW process with use of ER 70 S 2 Filler wire. (4). Balance Passes With SMAW process with electrode E 7018-1.(5). flushing of excess welding to match the adjacent area thickness.(6). Liquid penetrant testing before weld build up,after every pass of weld build up & After weld build up job completion.(7).Preheating of area as per job requirement before start of weld build up.(8) Cnotractor shall follow the weld build up guidelines of Engineer In charge.
500
-
-
... More
Supply of carbon steel pipe fittings as per details given below.
-
-
-
... More
1" NB x sch 80 seamless carbon steel pipes of A 106 GR B and dimension confirming to ANSI B 36.10
240
-
-
... More
1-1/2" NB x 3000# scoket weld type elbow material confirming to A 105 and dimension as per ANSI B 16.11
90
-
-
... More
1/2" NB x 3000# scoket weld type LR elbow material confirming to A 105 and dimension as per ANSI B 16.11
170
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements