Bhiwadi Integrated Development Authority Tender

Providing and applying tack coat with Bitumen grade VG-10 using mechanical bitumen pressure distributor at the rate of 0.30 to 0.40 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 510 and design mix for base/binder course including loading of material with F.E loader heating of binder aggregate and filler in approved hot mix plant as per clause 6.5 of manual transporting the mixed material by tippers and laying with sansor paver finisher as per clause 507.3.5 to the required level and grade rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 507,112] including antistripping agent .Grading II (19 mm nominal size) - Bitumen @ minimum 4.5 % of mix (VG-30 grade) & thickness 50 - 75 mm

Providing and laying bituminous concrete as per design mix on prepared surface with specified graded stone as per table 500-18 for wearing course including loading of aggregate with F.E loader and hot mixing of binder and 2% cement filler with aggregates in approved hot mix plant as per clause 6.5 of manual Transporting the mix material with tipper to paver and laying with sensor paver finisher (as per clouse 507.3.5) to the required level , grades and rolling with vibratory compactor and pneumatic tyred roller 150-250 KN,TP=0.7 Mpa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MORTH Specification : Clause -509,112) including Antistripping Agent Grade-II Bitumen @ minimum 6 % of mix with lead up to 1 KM VG-30 grade

Stripping excess soil from the shoulder surface including disposal of excess earth side slopes to achieve the approved level and compacting with plate compactor upto 75mm average depth complete as per MORTH specification clause 3003.

Earth work in excavation, including stacking/disposal of surplus material with all lifts and lead up to 50 meters, exclusive of compensation of earth (MoRTH specification : Clause 301 to 305) When excavation and loading is done mechanically using Bukll Dozer, Front-end loader and carriage is done up to 1 Km. by tipper/dumper (6T capacity).

Carriage of earth,sand, lime, morrum,manure orr sludge etc including loading, unloading complete with a lead of 5 KM.

Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level.M20 grade Nominal Mix 1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size).

Dismantling of cement concrete pavement by mechanical means using pneumatic tools, breaking to pieces not exceeding 0.02 cum in volume and stock piling at designated locations and disposal of dismantled materials upto a lead of 1000 metres, stacking serviceable and unserviceable materials separately as per MORTH specification clause 202.

Cement of un-reinforced, without dowel bar. plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design. laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound and water finishing to lines and grade as per drawing and MoRD Specification Clause 1501 including vaccum dewatering process with all reuired equipments.

Add extra for dowel Bar for Cement Concrete Pavement as per drawing and MoRD Specification Clause 1501

Providing and laying of hot applied thermoplastic compound inclusive type I reflectrosing glass beads as per table 800-3, 800-4 applied in uniform thickness of at least 2.5 mm and spread uniformly with reflectorising glass beads type II in addition @ 250 gms per Sqm with a road marking machine as per IRC: 35 complete with traffic diversion arrangement as per MORTH specification clause 803.4.