Bhiwadi Integrated Development Authority Tender

Cement of un-reinforced, without dowel bar. plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design. laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound and water finishing to lines and grade as per drawing and MoRD Specification Clause 1501 including vaccum dewatering process with all reuired equipments.

Providing laying and consolidation of crushed stone aggregates on prepared surface as per Built Up Spary Grout specification, 75 mm thick as base course compacted in 2 layers composite construction of crushed stone aggregates with application of bitumen binder VG-30 grade with spray set at the rate of 15 Kg per 10 Sqm after each layer and laying key aggregate on the top of second layer and rolling with power roller, 8-10 tonne, but excluding cost of primer/tack coat.[MoRTH Specification : Clause 506,112]

Providing and applying primer coat over prepared surface or granular base with bitumen emulsion(SS-1) as per IS: 8887 & manufacturer’s specifications @ 6 kg /10 sqm with a self propelled of towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI 502,112 ( Including cleaning of road surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion (RS-1) as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface )

Providing and laying Dense Bituminous Macadam on prepared surface with specified graded crushed aggregates as per table 510 and design mix for base/binder course including loading of material with F.E loader heating of binder aggregate and filler in approved hot mix plant as per clause 6.5 of manual transporting the mixed material by tippers and laying with sansor paver finisher as per clause 507.3.5 to the required level and grade rolling by self propelled power rollers and vibratory rollers or pneumatic tyred roller 150-250KN. TP=0.7MPa to achieve the desired density (approved by the department) but excluding cost of primer/tack coat. [MoRTH Specification : Clause 507,112] including antistripping agent Grading II (19 mm nominal size) - Bitumen @ minimum 4.5 % of mix (VG-30 grade) & thickness 50 - 75 mm

Providing and laying bituminous concrete as per design mix on prepared surface with specified graded stone as per table 500-18 for wearing course including loading of aggregate with F.E loader and hot mixing of binder and 2% cement filler with aggregates in approved hot mix plant as per clause 6.5 of manual Transporting the mix material with tipper to paver and laying with sensor paver finisher (as per clouse 507.3.5) to the required level , grades and rolling with vibratory compactor and pneumatic tyred roller 150-250 KN,TP=0.7 Mpa, to achieve the desired density (approved by the department) excluding cost of primer/tack coat (MORTH Specification : Clause -509,112) including Antistripping Agent Grade-II Bitumen @ minimum 6 % of mix with lead up to 1 KM VG-30 grade