Bhiwadi Integrated Development Authority Tender

Extra rate for carriage of mixed material additional lead from :- Beyond 20 Km

Cement of un-reinforced, without dowel bar. plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design. laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days,using curing compound and water finishing to lines and grade as per drawing and MoRD Specification Clause 1501 including vaccum dewatering process with all reuired equipments.

Providing and applying primer coat over prepared surface or granular base with bitumen emulsion(SS-1) as per IS: 8887 & manufacturer’s specifications @ 6 kg /10 sqm with a self propelled of towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI 502,112 ( Including cleaning of road surface )

Providing and applying tack coat on the prepared surface ,with bitumen emulsion (RS-1) as per IS : 8887 & manufacturer’s specifications @ 2 kg /10sqm. With a self propelled or towed bitumen pressure sprayer equipped for spraying the material uniformly at specified rates and temperatures as per MORTH specification CI.503,112 ( Including cleaning of Road Surface )

Add extra to item No. 6.1 for additional 0.1 Kg per Sqm emulsion

Add extra to item No. 6.2 for additional 0.1Kg per Sqm emulsion

Providing and laying seal coat for sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall, including rolling with a smooth wheeled roller 8 - 10 tonne capacity finished to required level and grades, complete as per MORTH specification clause 513.Laying by Mechnical Means.Type B - Premixed in in approved HMP as per clause 6.5 of manual having capacity 50 TPH comprising of aggregate (sand or grit) having size 2.36 mm to 180 micron @ 0.06 Cum per 10 Sqm and bitumen binder (VG-30 grade) @ 6.8 Kg / 10 sqm and laying by hydrostatic paver finisher with sensor control, including mixing, transportation, laying, rolling etc. complete - including carriage for 1 Km. lead.

Providing and laying open graded premix carpet 20mm thick (compacted) on prepared surface in a single course as wearing course aggregates as per Table 500-23, heating bituminous binder @ 14.6 Kg/10 Sqm.(VG-30 grade) and aggregates in Hot Mix Plant, transporting the mixed material with tipper and laying with paver finisher to the required level and grade, rolling with power roller, 8-10 tonne but excluding cost of tack and seal coat with lead for mix of material 1 Km.[MORTH Specification : Clause 511,112]Inciuliding Antistripping agent. In approved Hot Mix Plant as per clause 6.5 of Manual, including loading of aggregates with F.E loader with VG-30 bitumen.

Providing and laying bituminous macadam on prepared surface with specified graded crushed aggregate as per table 500 - 4, grading -1for base / binder course including loading of aggregates with F.E loader and heating and mixing of stone aggregate and bitumen in approved hot mix plant as per clause 6.5 of manual transporting the mixed material in tipper to paver and laying mixed material with sansor paver finisher to the required level and grade rolling by power roller & vibratory compactor to achieve the desired density (approved by the department )excluding cost of primer /tack coat [MoRTH Specification : Clause 504,112] 50-100 mm compacted thickness with 3.30% bitumen 60/70 grade with lead of mix 1 Km. including antistripping agent