Amber Development And Management Authority Tender

M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricks

Cement mortar 1 : 4 (1 cement : 4 coarse sand)

Plaster on new surface on wall in cement sand mortar 1:3 including racking of joints etc. complete fine finish :

25mm thick

Finishing with neat cement (punning).

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in :

Cement Mortar 1:5 ( 1-Cement : 5-Sand).

Supplying and fixing machine cut dressed 75 mm Pink sand stone (Bansi Paharpur) dasa/ coping wth ornamental shape having moulding and "PAN Shape" engraving as per required pattern with engraving depth of 5 mm (average) in single piece of length 90 cm to be laid on cement mortar 1:4 (12 to 20mm thick) including pointing with admixture of pigment matching with the stone shade.

Providing & fixing door, window, chowkhats and other frames, including antitermite treatment, M.S. flat, hold fasts of size 250 x 40 x 3mm fixed with M.S. bolt 5mm dia 50mm long duly embedded in cement concrete M-15 grade :

Ghana teak wood Grade - I.

Add extra in frames for circular members such as in fan lights, staircase railing etc.

Providing and fixing Nigeria / Ghana /Ivory Coast Teak wood grade-I mouldings and beadings in doors and windows size :-

50x12 mm

50x20 mm

Providing and fixing wall panelling using soft wood frame of size 50x25mm @600 mm c/c in both directions duly treated with anti-termite treatment making grooves painting of grooves specification and drawing using :

12 mm thick one side laminated board Practical board (Phenol bonded)

Providing and fixing sun control film, thickness of film 1 Mil Visible Light Transmittance 4-24% & Solar Energy Transmittance 42-51% & Total solar Energy rejection 37-43%of approved colour and shade , complete in all respect , at all level , as directed by engineer- in -charge.

Supply and Installation of ROOF – PREFABRICATED INSULATED PPGL FACE PANEL:Roof: Insulated sandwich panels for roof of total thickness mentioned below exclusive of crest height of top corrugation. Panel shall be made of 0.50mm (+/-0.04mm) thick pre coated metal sheet on both sides of rigid polyurethane insulation. The top external facing metal sheet shall have corrugated shape with crest. The trapezoidal shape crowns/crest height should not be less than 30mm. The pre-coated metal sheet shall be PPGL (Pre Painted Galvalume Sheet with AZ coating) sheet having SDP (Super Durable Polyester) colour coat of 18 micron (min). The bottom sheet must have tongue and groove type flange (U shape) of 8mm x 8mm on groove side and 8mm x 12mm on tongue side. Flange must be on lengthwise sides for joining adjacent panels. Panel's bottom side PPGL sheet must also be pre-strengthened by full lengthwise stiffening with semi-circular beading of 12mm width & 3 to 4mm depth at 240 (+/-5) mm pitch. The top corrugated sheet must have at-least one open crown/crest for overlapping adjacent panel widthwise. Similarly the top corrugated sheet must have suitable open extension of min 6” on bottom widthwise side of panel for overlapping further panels joined lengthwise also. The insulation core shall be self-extinguishing DIN 4102,Class B3 fire retardant class rigid PUR with thermal conductivity of 0.025 W/mK and with initial density of 40kg/m3 (+/-2kg) suitable for temperature range of -30 degree C to +80 degree C. The panel must be made using glue-free high pressure hot pressing self-bonding method. PPGL sheet on both sides of panel shall have a min15 micron protective plastic guard film to avoid scratches during transportation.

Thickness 105mm (+/- 2mm)

Supply and Installation of WALL – PREFABRICATED INSULATED CEMENT FACE PANEL: Factory-readymade structural reinforced insulated wall panel of thickness mentioned below. Panel shall be made of 6mm (+/-0.6mm) thick asbestos-free fiber cement sheet/ Cement bonded particle board as per IS:14276:1995 on both sides of rigid PUR insulation. The wall panel shall be vertically joined together with adjacent panel by biscuit joints lengthwise with suitable construction adhesive. Joining member (biscuit) shall be made of approx 12mm thick cement sheet /Cement bonded particle board as per IS:14276:1995. Panels may have optional provision for inbuilt electrical conduit running lengthwise at vertical center of specified panels. Both vertical lengthwise sides of panels must have full length MS tubes of min 1.0mm thickness for better structural strength.The final panel surface must be free from undulations. The Insulating core shall be self-extinguishing DIN 4102,Class B3 fire retardant class rigid PUR with thermal conductivity of 0.025 W/mK and with density of 40kg/m3 (+/-2kg) suitable for temperature range of -30 degree C to +80 degree C. The panel must be made using glue-free high pressure hot pressing self-bonding method and shall be free from major surface undulations. Thickness 75mm (+/- 2mm)

Bottom and Top U track : U-track for mounting panels with floor. The channel shall be made from minimum 1.15 mm thick PPGL sheet with flange height of minimum 35 mm and width as per thickness of panel used.

Flashings (inner and outer):Corner angle flashings of equal shape for covering various corners and open sides of panels. Flashings shall be made from 0.5mm thick pre-coated PPGL sheet in following sizes: 100mm x 100mm

Roof End Cap: End cap for closing ends of roof panels made from 0.5mm thick PPGL sheet.

Panel End Caps: U or L shape caps suitable for thickness of panel used, with 30mm flange. It should be made frem 0.5mm Pre coated PPGL sheet.

Frame for Door/Window: Frame shall be made out of min 1.15mm thick press steel sheet.

Adhesives

Dismantling stone slab/ terrazo chip flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meters lead.

Carriage & disposal of all unserviceable rubbish material upto distance of 10 kms including loading and unloading of material.

Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide

Extra if square,rectangular hollow tubelar sections are used or grill made by flats only

Demolishing lime concrete manually/ by mechanical means and disposal of material within 50 metres lead as per direction of Engineer-in-charge.

Demolishing mud phuska/ Lime dhar/ Kharanja in terracing and disposal of unserviceable material within 50 meters lead.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meter lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: For thickness of tiles 10mm to 25mm.

Stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of Engineer In Charge

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.

Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc.

Providing and applying Melamine polish on teak wood work of approved brand and manufacture to give an even shade with two or more coats by compressor including sand papering, wood filler coat etc complete in all respect:

New Surface

Old Surface

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work

Add extra for mirror polishing on existing marble work/ Kota stone flooring work where ever required to give high gloss finish complete.

Providing and fixing 1st quality MAT & GLOSSY finished ceramic tile confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed 1:4).

Size 300mm x 600mm

Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.

South Zed Black Above 3601 Cm2 Slabs

Extra for providing edge moulding to 15-18mm thick marble/ Granite/Kota stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Marble work

Full Edge moulding

Granite/Kota Stone Work

Full Edge moulding

Refebrication work with existing steel work including cutting, welding & refebrication as per requirement with fixing at site complete as per direction of Engineer In charge

Stone work (machine cut edges) for Wall cladding/ Veneering work up to 10 m height with 20 to 30 mm thick Pink Sand stone (Bansi Paharpur) and backing filled with a grout of 12mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing by means of cramps which shall be paid separately)

Exposed face Machine cut

Supplying and fixing machine cut fine dressed Red/Pink sand stone dasa or coping, with full moulding if required laid on cement mortar 1:4 including pointing with admixture of pigment matching with the stone shade. 50 mm thick