Amber Development And Management Authority Tender

Wall Panels (WP-T1) Providing and fixing of 230mm deep wall panels, designed as a combination of casement and information panel. Measurements may vary depending on site conditions as these are to be fixed in the existing arches or niches or a doorway; actual measurements to be taken from the site, by the supplier. Casement of depth 230mm, constructed with 50 x 50 mm x 4mm thk powder coated MS hollow section (grade 201 and above), spaced @600mm as a frame as per drawing to house the printed information panel; provision to fix concealed LED linear fittings (WP-Li1) as required to light the information panel is to be provided on the top housing as per the drawing. Edges touching the wall to be treated with anti-termite coatings and finished with low VoC matte paint, colour as specified. Four sides around the information panel to be cladded with 12mm thk low VoC plywood and ACP as the same colour as the ACP cladded on the information Panel. Information panel to be constructed with a framework of 25 x 25mm x 3mm thk powder coated MS (grade 201 and above) spaced @600mm c/c as a rectangle grid frame; cladded with a 12mm thick low VoC MR Grade and anti-borer and anti-termite plywood and graphic printed (content as approved by the Engineer-in-charge/ architect) 3mm thk (0.32mm Sheet thickness) Aluminium Composite Panels (Make Aludecor, Alstone) panel; colour as per selection. Print finishing UV coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Front area to be measured. Graphic Printing & Light cost paid separately.

Wall Panels (WP-T2) Providing and fixing of 230mm deep Stone cladded wall panels, designed as a combination of casement and information panel. Measurements may vary depending on site conditions as these are to be fixed in the existing arches or niches or a doorway; actual measurements to be taken from the site, by the supplier. Casement constructed with 50 x 50 mm x 4mm thk powder coated MS hollow section (grade 201 and above), spaced @600mm c/c as a frame as per drawing to house the printed information panel; provision to install a concealed LED linear fittings (WP-Li1) as required to light the information panel is fixed on the top housing as per the drawing. Edges touching the wall to be treated with anti-termite coatings and finished with low VoC matte paint, colour as specified. Four sides around the information panel to be cladded with 12mm thk low VoC plywood and white makrana stone. Information panel constructed with a framework of 25 x 25mm x 3mm thk powder coated MS (grade 201 and above) spaced @600mm c/c as a rectangle grid frame; cladded with a 8mm thick low VoC Grade and anti-borer and anti-termite plywood and 15-18mm thk first grade spotless white makarana marble slab (maximum single joint is allowed).Finishing coats shall be applied on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.Front area to be measured. Graphics Printing & Light cost paid separately.

Wall Panels Showcases (WPS) Providing and fixing of glass showcase of size 450mm x 600mm x 150mm, to house selected precious artefacts and reproductions. Sizes to be finalised with the approval of engineer-in-charge/ architect, based on the artefact sizes. Lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) showcases to be constructed with powder coated MS structure as per drawing and 12m thk low VoC plywood as base. Plywood base to be fixed to another 12mm thk upholstered base with microfibre fabric to be provided as finishing surface to keep the artefacts. Colours as per instruction. The glass cover for the showcases made of 6mm thk extra clear toughened glass to be provided on all 5 sides, bonded neatly together at the edges with glass-glass adhesives from companies like 3M or equivalent; and fixed to an aluminium extruded profile; as this open towards the front with hydraulic gas springs (make ACE or equivalent), as per selection. Provision to fix the selected light (S4) to be given in the structure. Best quality acrylic Props to mount the artwork to the showcase to be included. All glass panels should be from brands like Saint Gobain, Asahi, or equivalent make with no marking or branding logos. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Front glass surface (Length x Width) to be measured for payment. Light cost paid separately.

Pedestal Display Showcase (PD-T1) Providing and fixing of approximately 45cms deep (measurements may vary depending on site conditions as these come in the existing arches or a niche; to be checked at site, by the supplier) lockable showcase box over a pedestal. Base to be made in 12mm thk fire retardant plywood on all sides with 50 x 50 mm thk first class teak wood stained with water based low VoC polish as inside support. 700mm high base pedestal includes wooden skirting made as per drawing. Display area drawer to be covered on two sides (front and top) with 8mm thk extra clear toughened glass bonded together with glass-glass adhesives from companies like 3M or equivalent to an aluminium extruded profile. Display unit has to be made as a lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) drawer unit with the front and top glass opens with this drawer; operated with under-mounted drawer slides from brands like Hafele, Blum or equivalent. The Display surface to be upholstered with micro-fibre fabric, colour as specified. Best quality acrylic Props to mount the artwork to the showcase to be included. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Provision to fix the selected light (S1) to be given in the structure. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and height to be measured for payment. Selected Light cost paid separately.

Table Display Showcase Providing and fixing of approximately 120cms (length) x 45cm (width) x 100cms (height) (measurements may vary depending on site conditions as these come in the existing arches or a niche; to be checked at site, by the supplier) lockable showcase boxes over a table. Display height may vary from type to type. Ref Drawing. Base with legs to be made in 12 mm thk fire retardant plywood on all sides with 50 x 50mm thk first class teak wood stained with water based low VoC polish as inside support. Legs with wooden skirting made as per drawing. Display area to be covered with 8mm thk extra clear toughened glass bonded together with glass-glass adhesives from companies like 3M or equivalent on all four sides (including the drawer glass) fixed to an aluminium extruded profile. Display unit has to be made as a lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) drawer unit with the front glass opens with this drawer; operated with under-mounted drawer slides from brands like Hafele, Blum or equivalent. The Display surface to be upholstered with micro-fibre fabric, colour as specified. Best quality acrylic Props to mount the artwork to the showcase to be included. Provision to fix the selected light (S1) to be given in the structure. Best quality acrylic Props to mount the artwork to the showcase to be included. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and top Height to be measured for payment. Selected Light cost paid separately.

Table Display Showcase T1 (TD-T1 4.2F)

Table Display Showcase (TD-T2, 3.8F)

Table Display Showcase T2 (TD-T2, 4F)

Table Display Showcase T3 (TD-T3, 7.5F)

Table Display Showcase T3 (TD-T3, 4.0F)

Table Display Showcase and Table T4 (TD-T4) Providing and fixing of approximately 340cms (length) x 60cm (width) x 300cms (height) (measurements to be checked at site, by the supplier) lockable showcase boxes over a table. Display height may vary from type to type. Ref Drawing. Base to be made in 18/19mm thk fire retardant plywood on all sides with 50 x 50mm thk first class teak wood stained with water based low VoC polish as inside support. Base with wooden skirting made as per drawing. Seperate display area in the center to be provided as per drawing, that to be covered with 8mm thk extra clear toughened glass bonded together with glass-glass adhesives from companies like 3M or equivalent on all four sides (including the front drawer glass) fixed to an aluminium extruded profile. Best quality acrylic Props to mount the artwork to the showcase to be included.Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Display unit has to be made as a lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) drawer unit with the front glass opens with this drawer; operated with under-mounted drawer slides from brands like Hafele, Blum or equivalent. The Display surface to be upholstered with micro-fibre fabric, colour as specified. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and Height to be measured for payment. Selected Light cost paid separately.

Showcase Display (SD-T1) Providing and fixing of approximately 80cms (length) x 30cm (width) x 240cms (height) (measurements may vary depending on site conditions as these come in the existing arches or a niche; to be checked at site, by the supplier) lockable full wall showcase boxes. Base and the case to be made in 12mm thk fire retardant plywood on all sides with 50 x 50mm thk first class teak wood stained and with water based low VoC polish as inside support. 700mm high base including skirting as per drawing. Two sides (including the shutter) in 8mm thk extra clear toughened glass and the rest in 12 mm thk plywood. Lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) Full glass shutter to be made with 8mm thk extra clear toughened glass opens towards the front operated with minimum visible patch hinges, from brands of the likes Dorma, Simonswerk etc.; sample to be pre-approved. Display Area divided into glass shelves or upholstered with micro-fibre fabric shelves as per drawing, colour as specified. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. Provision to fix the selected light (WSD-D1) to be given in the structure. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and height to be measured for payment. Selected Light cost paid separately.

Showcase Display (SD-T2) Providing and fixing of approximately 240cms (length) x 30cm (width) x 240cms (height) (measurements may vary depending on site conditions; to be checked at site, by the supplier) lockable full wall showcase boxes. Base and the case to be made in 18/19mm thk fire retardant plywood on all sides with 50 x 50mm thk first class teak wood stained and with water based low VoC polish as inside support. 700mm high base including skirting as per drawing. Front side to be made with fixed glass panels and Lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) Full glass shutter to be made with 8mm thk extra clear toughened glass opens towards the front operated with minimum visible patch hinges, from brands of the likes of Dorma, Simonswerk etc.; sample to be pre-approved. Display Area is upholstered with micro-fibre fabric shelves as per drawing, colour as specified. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Provision to fix the selected light (WSD-D1) to be given in the structure. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and height to be measured for payment. Selected Light cost paid separately.

Showcase Display (SD-T3) Providing and fixing of approximately 300cm (length) x 30cm (width) x 240cms (height) (measurements may vary depending on site conditions as these come in the existing arches or a niche; to be checked at site, by the supplier) lockable full wall showcase boxes. To be made along with two information panels on both the sides of the showcase. The centre portion is designed in two parts; one fixed part to the wall and the second one as an openable shutter. The fixed part to be made in 50 x 50mm thk first class teak wood stained and with water based low VoC polish as inside support; covered with an upholstered micro-fibre fabric shelves as per drawing as shelves, colour as specified. The Lockable (small round showcase locks from the make of Yale, Hafele, Godrej etc; lockable from bottom) openable shutter to be hinged to the fixed part with branded heavy duty concealed hinges from the brands of the likes of Hafele, Simonswerk etc. Provision to fix the selected light (WSD-D1) to be given in the structure. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Front area complete Length and Height to be measured for payment. Selected Light cost paid separately.

Wall Display Shelf (WD-T1) Providing and fixing of a series of continuous shelving units for displaying the crafts of Rajasthan for the gallery GF22 Crafts of Rajasthan. Overall shelf body is 400mm deep and to be made in 50x50mm thk first quality teak wood stained with water based low VoC polish; covered with 12mm low VoC plywood; finished in low VoC paint as per selection. Horizontall and Vertical shelf members to be made in 18/19mm thk low VoC plywood. All shelves to have separate glass shutters of 8mm thk extra clear toughened lockable (best quality miniature locks for small glass shutters) glass shutter opens towards the front operated with miniature patch hinges, from brands of the likes Dorma, Simonswerk etc.; sample to be pre-approved. Provision to fix the selected light (S3) to be given in the structure. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and Height to be measured for payment. Selected Light cost paid separately.

Wall Display Shelf (WD-T2) Providing and fixing of a series of continuous shelving units for displaying the shop objects. Each shelf are of 500mm (length) x 500mm (height) x 400mm (depth) to make this large format shelving system Made in first Quality Teak wood stained with water based low VoC polish as the main support; covered with 18/19mm low VoC plywood; finished in low VoC paint as per selection. Horizontall and Vertical shelf members to be made in 18/19mm thk low VoC plywood. All shelves to have separate glass shutters of 8mm thk extra clear toughened lockable (best quality miniature locks for small glass shutters) glass shutter opens towards the front operated with miniature patch hinges, from brands of the likes Dorma, Simonswerk etc.; sample to be pre-approved. Provision to fix the selected light (S3) to be given in the structure. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and Height to be measured for payment. Selected Light and graphics cost paid separately.

Island Display (ID-GF10) Providing and fixing of customised island display as the centre-of-attraction for GF10 Greatest Grid Gallery. Made as two parts; plinth for the topographical model and a projection surface. Plinth is to be made around 240cm (length) x 240cm (width) x 104cm (Height) in size by powder coated MS L Sections of 50x50mmx4mm thk spaced @ 600mm c/c. Covered on all five sides with 12 mm low VOC ply fixed to the MS box and 12mm thk extra clear non reflective toughened glass as a cover to the topographical model, finished with low VOC (Volatile Organic Compounds) matte paint as per selection; colour as per selection. The projection surface of an approximate size of 240cm (length) x 250cm (Height) x 20cm (thickness) in 50x50mmx3mm thk powder coated MS L-section spaced @600mm c/c; covered with 18/19mm low VoC plywood; finished in low VoC paint as per selection. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Topographical model cost paid separately.

Island Display (ID-GF24) Providing and fixing of customised island display as the centre-of-attraction for GF24 Cultural Zone gallery. Size of 1800 mm lenght x2700mm height x 250mm width with bottom size 1800x960x100mm. Made as a box with powder coated MS L Section of size 50 x 50mm x 6mm thk spaced @600mm c/c. Covered on all five sides with 12mm thk Low VOC Plywood fixed to the MS box. Cladded on top is graphic printed 3mm (.35mm sheet thickness) Aluminium Composite panel. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Graphic cost paid seperately.

Island Display (ID-GF22) Providing and fixing of customised island display as the centre-of-attraction for GF22 Crafts of Rajasthan gallery. overall size of 384cm leght x 250 height x 220cm width (refer drawing no. ID-GF22) Made as per drawing with powder coated MS hollow box Section of size 25 x 50mm x 4mm thk spaced @600mm c/c. Covered on all sides with 12mm thk Low VOC Plywood fixed to the MS box. finished with low VOC (Volatile Organic Compounds) matte paint as per selection; colour as per selection; Both sides have two display systems inbuilt in the Island display- Glass showcase with front side 8mm thk openable glass panel has to be given with top and bottom in wood. Second side to be made as a display board to showcase various tools used in Rajasthan Craftsmen. This also has to be cased in 8mm thk extra clear toughened glass with miniaturised patch hinges and locks from makes like Dorma or Simonswerk etc. Provision to install the respective 3D reproductions to be given. Provision for installing respective light fittings to be provided. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Selected Light, 3D reproduction, Arts and crafts cost paid separately.

Furniture for seating- T1 (Fr-T1) Providing and fixing of wooden benches with approximate size of 120cm (Length) , 45cms (Width), and 45cm (Height), made with appropriate sections of Frist class teak wood stained and 50x50x4 mm, Stainless Steel (304 Grade) hollow box section legs to be provided, Top to be made as 50mm thick solid wooden top as per details mentioned in the drawing. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer in charge/ Architect is satisfied with the result. Treated with anti-termite coatings and finished withn superior quality PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Top area to be measured

Furniture for seating- T2 (Fr-T2) Sourcing and fixing of high quality complete plastic chairs with NO metal or wood for all guards, Museum staff and attendees, of approximate size of 50cm (length), 50cms (width) and 100cm (height with backrest). To be finalised, purchased or created based on the instructions from the architect/ engineer-in-charge. Makes: IKEA, GODREJ INTERIO or equivalent. To be completed as per approved design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Console Display- T1 (CD) Providing and fixing of wooden Console displays in the gallery with overall approximate size of 300mm (depth) x 2810mm lenght x 560mm heigh. (measurements may vary depending on site conditions as these come in the existing arches or a niche; to be measured at site, by the supplier). Fixed to the wall with appropriate hardware. Display base to be made of 12 mm low VOC ply and enclosed with 8mm thk extra cleaar thoughened glass (including drawer glass) to be fixed to the console display. Provision to install light (S2) to be provided. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Top area to be measured for payment. Selected Light cost paid separately.

Monitor Box- T1(Mo-T1) Providing and fixing of monitor cases for the safe keeping of monitors; constructed with 18/19mm thk low VoC Birch plywood and the front facia to be in 8mm thk extra clear toughened glass, with adequate support in wood as required; fixed to the wall with the standard heavy duty hardware for wall fixing for TV. Provision to open with a gass spring (make ACE and equivalant) towards the front to be provided for service and operations. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Front area to be measured for payment

For 32 inch Monitor (Mo-T1_32")

For 43 inch Monitor (Mo-T1_42")

For 55 inch Monitor (Mo-T1_55")

Customised Projector Mount- T2 (Mo-T2) Providing and fixing of false metal wall to mount the wall mounted projectors (with an average estimated weight of 30Kgs) mounts for all scenarios Powder coated MS Steel frame of size 50 x 50 x4 mm powder coated MS hollow pipe section welded @600 mm c/c (grade 201 and above) as main support; fixed to the wall with anchor bolts and the projectors are fixed by the standard heavy duty hardware for wall fixing for projectors. projector screen to be cladded over the metal frame to camouflage the frame. Treated with anti-termite coatings and finished with low VOC matte paint and superior qulity PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required till the Engineer-in-charge/ architect is satisfied with the result. Colour as per the instruction of the Engineer in charge/ Architect. Best quality acrylic Props to mount the artwork to the showcase to be included. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Length and Height to be measured for payment

Miscellaneous furniture (Fr-T3) Providing and fixing of various miscellaneous furnitures such as dispensers, News Paper/ Magazine holders, shelving for gallery guides, museum flyers, large font text for the elderly as per the drawings and instructions of the Architect/ engineer-in-charges. Constructed in 18/19mm thk birch ply with water based low VoC polish; To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Dispensers for Flyers of size 620 mm Lenght x 80mm depth x300 mm height (Drawing no.Fr_T3_B)

Publication Holders of size 400 mm Length x 130mm depth x1100 mm height (Drawing no Fr_T3_A)

Shelving units for Museum Brochure of size 400 mm Lenghtx 270mm depth x1320 mm height with 5 mm thick metel base size 700x360mm(Drawing no Fr_T3_C)

Large format text holders of size 400 mm Length x 130mm depth x1000 mm height (Drawing no Fr_T3_D)

Niche Spotlight housing Providing and fixing of 150 mm high bosed housing made of 3 mm thick alumnium or ACP for recessed or surface mounted lights for niches and arches; constructed with alumnium frame work of appropriate thickness and guage. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Bottom average area shall be measured.

Glass Railings Providing and fixing of 900mm heigh glass railings to prevent people from touching the valuable diplays in displayed inside the existing doorway-converted to a niche display setting, to be made with 12mm thick extra clear thoughened glass in extruded alumnium channel of appropriate size on all four sides for protection and for fixing, to be fixed to the wall and fixed to the floor with a wooden plinth made in 50x100mm thk plywood . To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Projection Screen Providing and fixing of 12mm the flat corian (Make: Dupont, LG, Samsung or equivalant) as cladding on wall with an alumnium support of 50x50x4mm hollow box section spaced at 600mm c/c. Surface has to be finished as matte for projection to be played on this. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Providing and fixing of Display Panel constructed as a combination of 50 x 50 mm first class teak wood frame spaced @600mm apart, cladded with 12mm thk fire retardant and anti-termite coated and low VOC plywood and Graphics printed (content as approved by the Engineer-in-charge/ architect) 3mm thk (0.35mm sheet thickness) Aluminium composite panels (Make Aludecor, Alstone). Panel made to be fixed on the wall and made openable wherever the A/C units are installed for its servicing; concealed hinges to be used for this from companies like dorma kaba, Simonswerk etc. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.Front area to be measured.

Providing & fixing of partition wall using Second class teak wood frame of size 50 x 75 mm @ 600 mm c/c in both directions duly treated with anti-termite treatment .The teak wood member frame shall be fixed rigidly at floor level with rawl plugs / wooden lugs. The frame work to be cladding with 12 mm thick low VOC fully fire retardant ply finish with 1 mm thick laminate as per pattern on both sides. as per suitable size complete with required hardware powder coated brass fittings complete as per design, drawing and as directed by engineer incharge (BWP Ply & Laminate : century, greenply & Merino make

Providing & fixing Touch Screen display cabinet 950mm Heigh to be made using 18/19 mm thick low VOC fully fire retardant Ply finished with superior quality PU coating, colour as specified. Finishing coats shall be sprayed on the surface in two or more coats as required on all visible surface. Display Back side height 900mm & front side 750 mm heigh. Top Side with cutout in the center for touch screen. front side openable door shutter for mini PC, 40x40mm Ghana teak wood mounding, beading including antitermite treatment complete with required hardware, powder coated brass fittings complete as per design, drawing and as directed by Engineer in charge/ Architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Top area to be Measured.

Providing & fixing display platform to be made using 18/19mm thick bwp marine fully fire retardant plywood 2 layers top finish 200mm high with 1mm laminate finish on all visible surfaces and 30mm Second class teak wood @ 600 mm C/C both side supports inside the structure complete with required hardware, powder coated brass fittings complete as per design, drawing and as directed by incharge. (BWP Ply & Laminate : century, greenply & Merino make) Top area to be Measured.

Providing and fixing of two step Lego game display table first step height 450 mm x2100mm lenght x 1250mm width made of outside 50x50 first class teak wood support cladding with 12mm bwp marine fully fire retardant plywood . Top side 2 layer 19 plywood and second step total height 620 mm x1300mm lenght x500mm width made of 19mm thick fire retardant plywood all side & top finish with all visible side 1 mm laminate. including 2000 Lego piece made of pvc Lego for building for games also including required first class teak wood mounding, beading including antitermite treatment complete with required hardware & fittings complete as per design, drawing and as directed by incharge

Providing and fixing Ceiling hung shapes (hexagon and triangles) using 3 mm thick ACP (Aluminum Composite Panels) 2 layer 150 mm thick. ACP ceiling hung with aluminum framework is supported from the ceiling with the help of 'J' hook and G.I. wire / 6-10mm G.I. rods of required sizes to maintain proper level etc. The aluminum framework is supported on side wall with the use of aluminum L-section of size 50x50 mm angles etc. Complete with required hardware Screw complete as per design, as directed by engineer incharge

Providing & fixing of Table, Top made of 25 mm thick BWP marine fully fire retardant plywood finish with 4 mm veneer the top side finish with melamine polish ,table support leg made of 50x50 mm First class teak wood finish with melamine polish .Item to include all necessary hardware including screws, nails, fevicol, etc. . as per design, drawing and as directed by engineer incharge .Table 600mm height, top Area to be measured. (BWP Ply & Laminate : century, greenply & Merino) make

Providing & fixing of 650 mm depth box display made of 12 mm Fully fire retardant plywood all side finish with 1 mm thick laminate approve colour shade. inside Support 50x50 mm thick Second class teak wood. Front Area open for sketch tablet including antitermite treatment complete with required hardware, powder coated fittings complete as per design, drawing and as directed by incharge .Display cabinet Front area to be Measured .

Providing & fixing Cube display 200 mm deep both side (Front & Back) 100mm one side to be made of 18/19 mm fire retardant plywood all side finished with 1mm laminate as per approve colour & shade all visible surface. Cube support 32 mm thick BWP blackboard. Provision for Led strip light in cube including antitermite treatment complete with required hardware & fittings complete as per design, drawing and as directed by incharge Front area to be Measured (cube size 300x300mm)

Providing & fixing of traditional ornamental Reception Table , Top made of 45 mm thick First class teak wood , all exposed surfaces & Internal support made of 45 mm First class teak wood finish with melamine polish . Internal shelves shall be of 19 mm thick teak wood. all inside surface of ply to be finish with melamine polish . Table all side 150x35 mm teak wood molding polish finish as per drawing at front. 25mm thick wood shutters cover of Shelf fixed with hinges finish with polish. Front 10 mm toughened glass fixed with 20x20 mm Frist class teak wood beading (glass 600 mm height ) . Table will be provided Drawer mobile & desktop pedestal fitted with meta box sliding system and front mounted single lock system Key Board Tray etc. complete .Item to include all necessary hardware including concealed SS hinges, concealed SS handles, SS knobs, locks, screws, nails, fevicol, etc. Table depth 680 mm . Table front Area to be measured

Providing & fixing of Reception Table Top made of 32 mm thick BWP Ply, all exposed surfaces made of 19 mm thick ply finish with 4 mm veneer the rear side of the table to be cladded in granite stone of approved colour stone to be fixed from top to bottom on the front & top side as shown in the drawing. Internal shelves shall be of 19 & 12 mm thick BWP board. all inside surface of ply to be finish with duco paint & polish of approved colour. Front side 35x50 mm second class teak wood cladding with 4mm teak veneer with polish finish as per drawing at front. Front side 10 mm toughened glass fixed with 50x100 mm first class teak wood frame & beading with allen bolt Table top made of 19 mm bwp ply with 4 mm thick veneer with polish. The Granite stone panel in front of the desk as shown in drawings. 100mm - 125mm high brass or stainless steel cut letters and museum logo to be stuck over the sandstone panel on the front side of the table and 75mm high on one side of the table as shown in the drawings or as directed by the Architect. Table will be provided Drawer mobile & desktop pedestal fitted with meta box sliding system and front mounted single lock system Key Board Tray etc. complete .Item to include all necessary hardware including concealed SS hinges, concealed SS handles, SS knobs, locks, screws, nails, fevicol, etc. Table 680mm depth, Front Area to be measured

Providing, & fixing of M.P teak Wood chair finish with Polished as per enclosed drawing. The size of chair shall be: the seat height 400 mm x 450mm width & ovarall back height 750 mm made of seat 25mm thick , leg size 50x50 mm thick, 30x50 mm thick support complete with required hardware as per design, drawing and as directed by incharge.

“Providing & Fixing of textile floor covering of Nylon 6.6 face fiber or equivalent of approved make with 100% Nylon and completely water proof resilient backing. The flooring should be Anti static+B32 with thickness of 4.3 mm and approximate weight of 1.8 kg./sqm of roll form. The carpet should be completely stain resistant and of a density approx. 80 million fibers/sq.mtr (70 million fiber/sq.yd) in the width of 2 mtr .The floor covering should have Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, SANITISED anti-microbial treatment, with resilient waterproof backing, anti allergic complete in all respect as per direction of Engineer-in-charge.

Providing and fixing of tree stump stool made of flexible polyurethane foam & Vinyl for kids with decorative design complete as per design, drawing and as directed by incharge. Size 350-400 mm dia, height 250 mm complete in all respect as per direction of Engineer-in-charge.

Supply and fixing notice boards (Soft Board) for display of information made of 50mmx50mm teak wood frame work all round and fitted with a pin – up board made of soft board and wrapped with approved colour and finish of fabric. The TW frames finished to desired wood effect by melamine polish after necessary surface preparation. complete in all respect as per direction of Engineer-in-charge.

Supplying & fixing white board fully scratch resistant ceramic steel board surface, non absorbed dry erase or permanent marker ink cleanable with any non absorbive cleaner with almunium frame & plastic corners as per as specifications & directions of the Engineers in charge

Providing and fixing 4500 GSM hand knotted traditional design pattern 100% handspun wool rug carpet 100 knots. Pile height 6-8 mm as per approved sample/design/color/size. Completed as per the instructions of the Engineer-in-Charge ( Make-Cocoon Fine Rugs. Jaipur Rugs & equivalent make)

Providing and fixing carpet of 2000 gsm traditional design pattern.100% wool cut pile carpet pile height 8-10 mm including backing as per approved sample/design/colour/size including Underlay of PU Foam of 8mm thick with adhesive etc. as per direction of Engineer Incharge complete ( Make-Cocoon Fine Rugs. Jaipur Rugs & equivalent make)

Providing and placing of solid M.P teak wood hand carved antique style chair, 4 leg carved in solid wood, seat high quality upholstery fabric filling in high quality Pu foam chair finish with Pu Polish approved polish colour and finish of fabric. complete as per design, drawing , photographs and as directed by engineer-in- charge. size of chair W 450mm x D 450mm xH 930 mm"

Providing and placing of solid M.P teak wood hand carved antique style 1200mm dia round top table 50mm thick table top base & 100-100 mm table top side heigh 25-30 mm carved wood . Table base of carved in solid wood with Pu Polishcomplete as per design, drawing , photographs and as directed by engineer-in- charge Table size 1200mm dia & 750 mm height.

Providing and placing of solid M.P teak wood wood hand carved antique style 6 seater rectangular table 50mm thick table top base & 100-100 mm table top side heigh 25-30 mm carved wood . Table leg 80-100 mm carved in solid wood with Pu Polish complete as per design, drawing , photographs and as directed by engineer-in- charge Table size 1800mm x1200 mm x750mm height.

Providing and placing three seater sofa, inner frame, basic structure made of soild M.P teak wood with upholstery 40kg/m3 ,130mm thick of foam in seat and 32kg/m3 ,90 mm thick of foam in back , Back foam Leatherette tapestry with 1+/-.1 mm thick and arms are made of sheesham wood a support with base frame & legs which are made of teak wood finish with PU polish. Complete as per the approved sample/image/ shop drawing and as per the direction of Architect & Engineer-In-Charge. Size of sofa (L)2100x(W)900x(H)800

Providing and placing Singal seater sofa, inner frame, basic structure made of soild M.P teak wood with upholstery 40kg/m3 ,130mm thick of foam in seat and 32kg/m3 ,90 mm thick of foam in back , Back foam Leatherette tapestry with 1+/-.1 mm thick and arms are made of sheesham wood a support with base frame & legs which are made of teak wood finish with PU polish. Complete as per the approved sample/image/ shop drawing and as per the direction of Architect & Engineer-In-Charge. Size of sofa (L)800x(W)900x(H)800

Providing & Placing carved antique style center table made of soild M.P teak wood frame with 10mm thick beveled edge toughened glass top & 50-60 mm thick carved teak wood leg to be provided. table finish with PU polish of approved colour & shade. complete as per the approved sample/image/ shop drawing by supplier and as per the direction of Architect & Engineer-In-Charge.Size of center table (L)1200x(W)600x(H)450mm

Supplying and placing in position chair of the following specifications. The cushioned seat assembly shall consists of insert polyurethane foam upholstered with foam laminated mesh fabric. The back shallmade up of two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main assembly. indicative Size of back shall be (W)-48.5cm, (H)-62.0cm & indicative size of seat shall be (W)-46.0cm x (D)-52.5cm.armrest shall be injection moulded with height adjustable up to 4.5+/-0.5cm in 3 steps and width adjustable up to 20mm. The mechanism of chair shall have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket shall made of Aluminium diecast piece connecting back with mechanism.The chair shall be provided with pneumatic height adjustment (Minimum of BIFMA standard Class 3) which shall have stroke of 9.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The indicative size of the pedestal shall be 66.0 +/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. indicative Overall dimensions of Chair shall be, Width of Chair - 76.0cm, Depth of Chair - 76.0 cm as measured from pedestal below. Height from ground - min 100.0 to max 109.0 cm. Seat height - min 45.0cm to max 54.0cm. Dimensions tolerance / variations shall be within +/- 1 cm. MESH FABRIC: Mesh Fabric shall be 100% Polyester weighing not less than Weight: 370 GSM, having abrasion value of over 50000, fastness to colour greater than 4, fastness to rubbing 4 or better(BS 1006 (1990). SEAT FABRIC: Seat Fabric shall be 100% Polyester weighing not less than Weight: 257GSM, having abrasion of over 36000, fastness to colour greater than 4.5, fastness to rubbing 4 or better(BS 1006 (1990). POLYURETHANE FOAM: 45kg/m3 or higher density foam in seat as per manufacturer's specifications. ARMREST ASSEMBLY: The armrest assembly shall be per manufacturer’s specifications having armrest structure in polished aluminium with 2 directional ( height and depth) adjustable PU arm tops. The products should be as per BIFMA standards, all complete as per specicitions, tender drawings, Reference images, approved samples/shop drawings and direction of Engineer - In - Charge. Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and fixing of modular storage made of 18mm thick three layer pre-laminated particle board of grade II Type III of IS 12823 designation PLB 23 of approve decorative color laminate in swede/matt finish on front. Opennable /swing door storage with hindges, ss finish handels and Front multi purpose lock , adjustable shlef for keep file according to user comfortability . Distributed load capacity of shelf should be 35kg . complete storage made of 18mm thick prelaminated particle board. .Complete storage shall be have knock down system . all fat edges duly sealed with 0.8/1/2mm thick machine pasted PVC beading. The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II should meet long time loadbending , screw - withdrawl strength and moudulus rupture and modulus of elasticity bending test as per IS 2380 (Part 4 ,Part 13 and Part 14). complete as per the approved sample/image/ shop drawing by supplier and as per the direction of Architect & Engineer-In-Charge. Size (L)750x(W)450x(H)1200 Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and fixing of modular table with work top made of 36mm thickness pre-laminated particle board of grade II Type III of IS 12823 of approve decorative color laminate on front and back side with white balancing laminate. lower part of the top will be encased with aluminium section edging 25x10x1.5mm with front three layer design below the work top on edges .Pre-laminated particle board of grade II Type III of IS 12823 Modesty panel shall be 18mm thick prelam particle board (PLPB) clad with decorative laminate on both side , edges shall be sealed with pvc edge beading. Complete table having knock down system on kd fittings. Table shall have one hydraulic deskport with provision of power point, voice & data. etc (L)1800x(W)750x(H)750 Drawer Unit :- Darwer unit below the table top. 2 file drawer and 1 box drawer. The drawer front, back and side panels are made out of 18mm pre-laminated particle board(PLPB) , edges dully sealed with pvc edge beading . The drawers boxes are mounted on rollers slides to enable smooth operation of the drawer . Drawer runs on soft closing telescopic channel The pedestal will have central locking mechanism and handels. (W)500 X (D)450 X (H)600. SIDE TABLE:- Side storage cabinet carcass & drawer unit , top made of 25mm thick and rest body like shelves , back and shutters shall be made up of 18mm thick Pre-laminated particle board of grade II Type III of IS 12823 . Side unit top made of 18mm thick with pvc edge beading on edges. Work top shall be supported on side unit and Fixed drawer unit. (L)1050x(W)450x(H)650 BACK UNIT:- Top made of 25mm thick and rest body made of 18mm thick three layer pre-laminated particle board of grade II Type III of IS 12823 of approve decorative color laminate on front. Storage will have swing shutters on soft closing hinges with locking system ,adjustable shlef in storage for keep file according to user, all panels shall be of 18mm thick prelam particle board of grade II Type III of IS 12823 of 18mm thickness , edges dully sealed with pvc edge beading . Complete knock down system . Storage with lock and handels. (L)1800x(W)450x(H)650 . The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II should meet long time loadbending , screw - withdrawl strength and moudulus rupture and modulus of elasticity bending test as per IS 2380 (Part 4 ,Part 13 and Part 14). complete as per the approved sample/image/ shop drawing by supplier and as per the direction of Architect & Engineer-In-Charge. Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and fixing of modular table with work top made of 25mm thickness prelam particle board of interior grade II Type III as per IS 12823:1990 with flat edges, work top clad with decorativie laminate on front as per standard and back side with white balancing .Flat edges duly sealed with 2mm thick machine pasted PVC beading . Worktop supported by 25mm thick gable and 18mm thick modesty panel made of prelam particle board of interior grade II Type III as per IS 12823:1990 with flat edges, Meeting table with 2 nos metal brush flaper with metal tray made of CRCA steel 1.2mm thick for wire managment and switich/socket mounting provison. Verticl cable riser made of CRCA steel 1.2mm thick for provision of moving wires from floor to flaper. all CRCA steel components / parts pcowder coated of 50-60 micron. The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II should meet long time loadbending , screw - withdrawl strength and moudulus rupture and modulus of elasticity bending test as per IS 2380 (Part 4 ,Part 13 and Part 14). size of 3000X1200X750 Complete as per the approved sample/image/ shop drawing by supplier and as per the direction of Architect & Engineer-In-Charge. Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and fixing of modular table with work top made of 25mm thick pre-laminated particle board of interior grade II as per IS 12823:1990 with flat edges, work top clad with decorative laminate on front as per standard and back side with white balancing .Flat edges duly sealed with 2mm thick machine pasted PVC beading .Table shall have four legs made of welded prime quality CRCA steel , Triangular ERW tubular frame of 53X53X75mm size and of 1.6m thick, leg have level adjuster PVC shoes with plastic color shoes cap, both leg jointed by 75x30x15mm die casted jointer through rectangular tubular pipe of 40x20mm size and 1.6mm thickness. Table with hydraulic desk port with provision of 6 amp three pin power point, voice, data for cat 6 wire , USB , HDMI and VGA point. All CRCA steel components / parts powder coated of 50-60 micron Side table unit with work top made of 25mm thick pre-laminated particle board of interior grade II as per IS 12823:1990 with flat edges, work top clad with decorative laminate on front as per standard and back side with white balancing .Flat edges duly sealed with 2mm thick machine pasted PVC beading. The top should be fixed on bottom drawers storage with 4 nos. 40mm dia. SS Tube pipes as/ref. image. storage cabinet carcass , shelves , back and shutters shall be made up of 18mm thick Pre-laminated particle board of grade II as per IS 12823 , , it should have 3 drawer with soft closing telescopic channel for sooth operation of drawers. inner box all drawers shall be made of 18mm thick , shutter with lock and handle all drawer and shutter have 4'' brush finish branded handle , drawer lock with front lock systems. All CRCA steel components / parts powder coated of 50-60 micron. The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II should meet long time loadbending , screw - withdrawl strength and moudulus rupture and modulus of elasticity bending test as per IS 2380 (Part 4 ,Part 13 and Part 14). complete as per the approved sample/image/ shop drawing by supplier and as per the direction of Architect & Engineer-In-Charge. size of (L)1800x(W)750x(H)750 Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing & Placing center table with first class solid teak wood frame with 10mm thick beveled edge toughened glass top & 20mm thick veneered ply bottomcompartment to be provided. Polishing and Varnishing – General Holes and indentations on surface shall be filled with putty made of whiting and linseed oil. The pad shall be moistened with polish and rubbed hard on the surface applying the polish sparingly but uniformly and completely over the entire surface. Another coat shall be applied in the same way after the first coat has dried sufficiently. Finishing coats shall be sprayed on the surface in 2 coats or as required till the satisfied result, using melamine polish of approved make. Application of extra coats shall not charged extra.complete as per the approved The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II should meet long time loadbending , screw - withdrawl strength and moudulus rupture and modulus of elasticity bending test as per IS 2380 (Part 4 ,Part 13 and Part 14). complete as per the approved sample/image/ shop drawing by supplier and as per the direction of Architect & Engineer-In-Charge. Size of (L)900x(W)900x(H)450 Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and placing ergonomical, comfortable and aesthetically design high back chairs. The seat size shall be 500mm (W) x 500mm (D) and the back size shall be mm 500(W) x 750mm (H) (Seat to back height). The seat and back shall be made of hot pressed moulded double layered plywood 16mm thk and Urethane foam upholstered (Foam density 40kg/m3) with Synthetic leather tapestry. The back shall be Urethane foam upholstered (Foam density 32kg/m3) with Leather tapestry. The armrests are made of CRC pipe 50mm X 15mm X 1.6mm chrome plated and cushion with foam and Synthetic leather tapestry. The mechanism shall be 360 degree revolving Torsion bar with single point locking and tension arragment. The pneumatic height adjustment shall have an adjustment of 65mm BIFMA Standard class 3. The pedestals shall be made of HR steel 1.2mm thk, chrome plated fitted with 5 nos. twin wheel castors. The pedestal dia shall be 65+/-0.5cm and the pitch centre dia shall be 75+/-1cm (with castors). The twin wheel castors shall be injection moulded in black nylon. Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and placing single seater sofa, inner frame, basic structure made of Marandi hard wood and commercial ply frame with upholstery 40kg/m3 ,130mm thick of foam in seat and 32kg/m3 ,90 mm thick of foam in back , Back foam Leatherette tapestry with 1+/-.1 mm thick and arms are made of Hard wood and commercial plywood and upholstered with foam 32kg / m3 and support with base frame & legs which are made of SS 202 grade, Pipe dia 30mm X 30mm X 1.5 thk chrome finish with PVC shoe. Complete as per the approved sample/image/ shop drawing and as per the direction of Architect & Engineer-In-Charge. size (L)800x(W)750x(H)800 Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Providing and placing three seater sofa, inner frame, basic structure made of Marandi hard wood and commercial ply frame with upholstery 40kg/m3 ,130mm thick of foam in seat and 32kg/m3 ,90 mm thick of foam in back , Back foam Leatherette tapestry with 1+/-.1 mm thick and arms are made of Hard wood and commercial plywood and upholstered with foam 32kg / m3 andsupport with base frame & legs which are made of SS 202 grade, Pipe dia 30mm X 30mm X 1.5 thk chrome finish with PVC shoe. Complete as per the approved sample/image/ shop drawing and as per the direction of Architect & Engineer-In-Charge. Make-GEEKEN, INDO INNOVATIONS, GODREJ INTERIO, ERGO TOUCH, AMARDEEP DESIGNS

Supply & Installation of Heavy Duty Shelving System of 3900mm w x 1000mm d x 2000mm h made of high strength mild steel. 3 loading levels with 1 tn load per level. Powder coated finish of approved colours complete as per design, drawing and as directed by in charge

supply and installation of mobistak mobile storage system on site including roll-pull out art panels storage carriage units size of 3.0 m length, 450mm width, 3m height. mode of tubular steel with welded heavy-duty braided 8 gauge wire mesh 2"x2" powder coated finish of approved colors including S.S huks, anchoring to the floor complete as per design, drawing and as directed by incharge.

supply and installation of mobistak mobile storage system on site including roll-pull out art panels storage carriage units size of 3.0 m length, 450mm width, 3m height. mode of tubular steel with welded heavy-duty braided 8 gauge wire mesh 2"x2" powder coated finish of approved colors including S.S huks, anchoring to the floor complete as per design, drawing and as directed by incharge.

supply and installation of mobistak mobile storage system on site including roll-pull out art panels storage carriage units size of 3.0 m length, 450mm width, 3m height. mode of tubular steel with welded heavy-duty braided 8 gauge wire mesh 2"x2" powder coated finish of approved colors including S.S huks, anchoring to the floor complete as per design, drawing and as directed by incharge.

Supply and installing Mobistack system with boltless units mounted on mobiles undercarriage with specially designed roll formed powder coated 14 bend panels of 1300 mm Length, hooked to powder coated uprights of 6 bend profile via adjustable shelf clips with front box cladding on drive handle side, rear box cladding , inner side plain cladding , end back plain cladding , 5 drawer of rack size(4' 4-1/2"Wx 2' 10"D x 6' 10.8"H) and drawers. Mobistak sides and backs are fully cladded with, uprights and panels of 1mm thk. System is provided with high strength high precision modular under carriage with cast iron wheels which runs on the rail. Drive unit is connected to undercarriage via sprocket and chain assembly. System is tested with 30,000 cycles equivalent to 10 years of operations . System is provided with load carrying capacity of 150kg/panel , wherein each panel is 1 mm thick with additional support of one stiffener per panel fitted below panel. System is embedded with special stability features , such as anti-tipping and anti-toppling mechanism. System is provided with special lock knob arrangement or operator safety . System enables minimum noise level while operations i.e within industrial norms of 70db . Rectangular rails with tapered plates are provided for ease of movement inside the aisle.

Sourcing of Licensed Digital Images on Jaipur and Rajasthan from public and private museums/institutions/individuals and authorised third-party image platforms as per the approved digital image sourcing list from engineer-in-charge/museum design consultant. Image sourcing expert to Identify, shortlist, liasise, coordinate for acquring image license from different organisations, (on payments by the main bidder), the licensed image would be sourced in the approved image size, of at least A3 size (0.42mt height/width, proportional width/height) in a minimum of 250 dpi for fine art printing. System work for each sourced digital image including colour correction, image cut out, creation of print-ready file, layout work for printing as per requirement. Maximum qty. of Images to be sourced: 700, payment as per actual no. of images procured as per approved list. Image sourcing platform: Alamy, Getty Image, British Library, Victoria & Albert Museum and other International and Indian private and public institutions as required. (Payment Shall be made only for displayed images)

Archival Printing of Sourced Archival Images Digital Fine Art Printing on imported museum quality acid free cotton rag/bamboo rag fine art paper with resistance to aging to least 30 years, as per approval of engineer-in-charge/museum design consultant. Thickness: 290-310 gsm or more Colour: White/Natural white Paper Make: Hahnemühle/GDS/Fotospeed Type of Paper Sizes: 1. 0.21 m x 0.297 m, approx. qty: 120 2. 0.297 m x 0.42 m, approx. qty: 45 3. 0.3 m x 0.3, approx. qty: 10 The final delivery and installation as per satisfaction of engineer in charge/museum design consultant. The printing to be done by certified studio/dealer for digital fine art paper and printing on approved paper.

Providing and Fixing Mounting and Framing with Wooden Box Frame Frame : Imported Box frame in imported art frame wood with thickness of 35-40mm and front of 9-15mm front width, matt finish, white/black colour as per required. Profile section and thickness to change as required structurally as per the size of required. Barrier board at the back. Mount board: Window cut mounting as per requirement of 2D art exhibits, with a 3-inch mount on all sides as per requirement. Back mount hinged to front window mount. Mount boards are with white solid core, where the front is white / off-white / black / any other colour, corresponding to the wall colour of the gallery or as specified by museum design consultant, with a minimum thickness of 1.35mm. Museum Art Glass: 1% or lesser reflectivity of glass and minimum of 70% UV protection. Approx. Size and Qty/Each 1. 30x22 in, approx. qty: 50 2. 22x15 in, approx. qty: 50 3. 16x13 in, approx. qty: 50 Glass Make: Groglass (Art glass)/Truvue Archival Mountboard Make: Peterboro/Colour Mount/CRESCENT The final delivery and installation as per satisfaction of engineer in charge/museum design consultant

Providing and Fixing Mounting and Framing with Mount Board of White Solid Core with Aluminium Frame Frame: Nielsen (Germany) Aluminium Frame (25.4 mm Height x 4.8mm width ), White/Black matt finish as required. Profile section and thickness to change as required structurally as per the size of required. Barrier board at the back. Mount board: Window cut mounting as per requirement of 2D art exhibits, with a 3 inch mount on all sides as per requirement. Back mount hinged to front window mount. Mount boards are with white solid core, where the front is either white or off-white or cream, or any other colour including black, with a minimum thickness of 1.35mm. Aluminium frame or moulding thickness of 25mm and 4-10mm front width, with same company's hardware and hanging hardware in Matt Black or White colour as required. Museum Art Glass: 1% or lesser reflectivity of glass and more than 70% UV protection. Approx. Size and Qty/Each 1. 30x22 in, approx. qty: 50 2. 22x15 in, approx. qty: 50 3. 16x13 in, approx. qty: 50 Glass Make: Groglass (Art glass)/Truvue Mountboard Make: Peterboro/Colour Mount/CRESCENT The cost includes a team from the framer for verification of object size in Jaipur, including travel, lodging and boarding. Cost of shifting mounting and framing equpment at project site in Jaipur. The final delivery as per satisfaction of engineer in charge/museum design consultant.

Providing and Fixing Mounting and Framing with Mount Board of Black Solid Core with Aluminium Frame Frame: Nielsen (Germany) Aluminium Frame (25.4 mm Height x 4.8mm width), black matt finish. Aluminium frame or moulding thickness of 25mm and 4-10mm front width, with same co. hardware and hanging hardware in Matt Black or White colour as required. Profile section and thickness to change as required structurally as per the size of required. Barrier board at the back. Mount board: Window cut mounting as per requirement of 2D art exhibits, with a 3 inch mount on all sides as per requirement. Back mount hinged to front window mount. Mount boards are with black solid core, where the front is black of Museum grade quality and the back is Mount board with white solid core, with a minimum thickness of 1.35mm. Museum Art Glass: 1% or lesser reflectivity of glass and more than 70% UV protection. Approx. Size and Qty/Each 1. 30x22 in, approx. qty: 50 2. 22x15 in, approx. qty: 50 3. 16x13 in, approx. qty: 50 Glass Make: Groglass (Art glass)/Truvue Mountboard Make: Peterboro/Colour Mount/CRESCENT The final delivery and installation as per satisfaction of engineer in charge/museum design consultant. The cost includes a team from the framer for verification of object size in Jaipur, including travel, lodging and boarding. Cost of shifting mounting and framing equpment at project site in Jaipur.

Providing and Fixing Large Frames with aluminium framing and museum art glass for large exhibits and for multiple small exhibits mounted together in one frame. Frame: Nielsen (Germany) Aluminium Frame (54 mm Height x 22mm width ) Black matt Finish. Mounting and Framing with Aluminium frame. Mount board: Window cut mounting as per requirement of art exhibits. Back mount hinged to front window mount. Mount boards are with white solid core, where the front is white / off-white / black / any other colour as per requirement, with a minimum thickness of 1.35mm. Barrier board at the back. Museum Art Glass: 1% or lesser reflectivity of glass and 70% or more UV protection. Size: approx. 90x120cms/each (largely 10-15 sft area) Glass Make: Groglass (Art glass)/Truvue Mountboard Make: Peterboro/Colour Mount/CRESCENT The cost includes a team from the framer for verification of object size in Jaipur, including travel, lodging and boarding. Cost of shifting mounting and framing equpment at project site in Jaipur. The final delivery and installation as per satisfaction of engineer in charge/museum design consultant.

Digital Print Supplying and installation of UV Digital Colour Printing on ACP with PU coating. Printing on with text, image and illustration as per final design. Images in four colour CMYK ink on panels, with Text. PU coating on entire panel surface. The final delivery and installation as per satisfaction of engineer in charge/museum design consultant. Content development, illustrations, 2D, 3D graphics for all printed display surfaces/large image blow up, captions etc. in the museum. The creation of graphics includes layout design, typography, test files, colour schemes. The final delivery as per satisfaction of engineer in charge/museum design consultant.

Images in four colour CMYK ink on panels, with Text in single colour black.

Images in four colour CMYK ink on panels, with Text in single colour white

Main Title Signage- Mild Steel Metal Lettering on West Building Facade (MT-01) Providing and fixing of polyurethane coated matte finished 2mm thk MS laser cut Letters writes, ‘Rajasthan Heritage Museum” in two languages (English and in Hindi) on main building facade with dowels carefully anchored into the building façade with appropriate grouting made to the wall and finishing appropriate to the extreme weather of Rajasthan; internal support to be made with powder coated 25mm x 25mm x 3mm MS hollow box sections. Provision to have with an 8mm wide LED strip light of at least 10-12W/meter or 450 lumens per foot (1500 lumens per meter) encased inside an high quality aluminium body bend to make the shape of the letters.Waterproof strip shuold be silicone injected and silicone covered.Ideal for outdoor usage with an IP68 rating ; 2800K, 3000K,4000K. To be installed after demo at site ,To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Long Title Signage- Signage on the East Facade (MT-02) Providing and fixing of polyurethane coated through and through laser cut 2mm thk MS sheet with the design approved by the Museum design Consultant/ Engineer in charge; to be made with 25mm x 25mm 3mm thk powder coated MS hollow box sections as support frame at the back. Provision to have back lighting to be provided with appropriate LED Modules (with IP65 rating or higher) and a diffuser. The housing need to be welded to the Metal frame and sealed all edges to prevent rainwater seeping inside the light housing. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production. Lighting cost to be included in this cost.

Inauguration Plaque Providing and fixing of Innaugural stone plaque; to be made in 1200mm x 600mm x 20mm thk carefully selected spotless first grade white makrana marble with 4mm deep inlay of the texts and graphics (as approved by the museum design consultant/ Engineer in charge)in deep blue stone and other stone as per design. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Entrance Long ACP Signages (AP-01) Providing and fixing of 3mm thk (0.35mm sheet thickness) ACP Entrance signages with graphics print as the Entrance signage for the entry corridor. To be mounted onto 12mm thk exteriour grade anti termite treated plywood fixed to 50x50x3mm aluminium box sections spaced @600mm c/c to make a framework fixed onto the wall. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Multiple Purpose Corian Signages for the gallery Providing and fixing of 12mm Corian signages with 4mm thk Corian inlay for multiple typologies of signage throughout the building. To be mounted onto 12mm thk exteriour grade anti termite treated plywood fixed to 50x50x3mm aluminium box sections spaced @600mm c/c to make a framework fixed onto the wall. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.

Captions Providing and fixing of artwork captions made in combination of paper for printing the caption, acrylic as cover and plywood as the mounting surface. Caption narration printed on to 130 gsm imported acid free paper as per selection and protected/ covered with 2mm thk bent (as per drawing) clear acrylic sheet from brands like trueVUE or equivalent. To be mounted on 8mm thk exterior grade plywood from makes like century ply or greenply or equivalent with slide-in provision made for the paper and acrylic to house neatly. The plywood housing to be fixed to the wall/ display panel (WP)/ horizontal display panel (WPH) as per the requirement. To be completed as per approved drawing, design, sample and direction of the engineer-in-charge/ architect. Contractor/ Vendor should have to prepare one sample and only after getting it approved from the Engineer in charge/ Architect, they should start the actual production.