Technical Education And Industrial Training Department Tender

Models of Safety valve, blow off cock, steam stop valve, Feed check valve, economizer , One Metallic Cut Section Model of each component

Model of air compressor , Metallic Cut Section Model

Model of Lancashire Boiler , Metallic Cut Section with details

Model of Nestler Boiler , Metallic Cut Section with details

Demonstration Actual Cut Section Model of Two Stroke Single Cylinder Petrol Engine , Original dissected, two stroke single cylinder petrol engine of a scooter. Engine consisting of carburettor etc. Complete with all salient parts sectioned for study of the various components and their functions.

Model of Solex carburettor , Original carburettor duly sectioned and mounted on base.

Model of Amal carburettor , Original carburettor duly sectioned and mounted on base.

Model of Ignition System of an automobile , Model consists of a switch, ignition coil, distributor, three plugs with necessary connections and terminals for battery connections.

Model of Water Cooling System of an Automobile , Metallic Model showing various parts of water cooling system

Model of Lubrication System of I.C. Engine , Metallic Model showing various parts of Lubrication system

Four Stroke three Cylinder Petrol Engine Test Rig with Electrical Dynamometer , A Four stroke three cylinder petrol engine developing about 10.0 HP at 1500 RPM variable speed with standard accessories. Engine is provided with self-starter, battery, dynamo, lubrication oil filter, fuel pump, ignition coil, exhaust silencer, choke control and throttle control. switches for conducting Morse test, electrical dynamometer which is directly coupled. Electrical motor with a swinging frame and spring balance to measure the load. Fuel Measuring Arrangement with fuel tank, fuel piping, measurement of fuel consumption by a burette and a three way cock connecting tube. Air Intake and Exhaust Gas Measurement M.S. tank, mounted on iron stand, fitted with suitable orifice plate, manometer, temperature sensors for measuring air intake temperature and exhaust gas temperature. The entire temperature sensor measuring device and manometer are mounted on panel board. It also consists of ignition and starting switch, fuse unit pilot lamp, throttle control switch, choke control switch, and switch assembly for cutting off each cylinder for conducting Morse test.

Model of MPFI system , Metallic showing various parts of system

Model of CRDI system , Metallic showing various parts of system

Refrigeration Tool kit , Kit consists of cutting tools, bending tool, flaring tool , swaging tool & brazing tool for copper pipe

Ampere meter , Range 0 to 30 amp AC

Pressure gauge , Size 0 to 300 lb per sq Inch.

Compound gauge , 30 to 0 to 150 lb. 2.5 inch dial 1/8 inches HPT

Ring spanner set , 1/8 inch to 1/2 inch

Thermometer with Case , (Range 0 to 250 Degree Celcius)

Swaging tool set , 1/4 inch to 3/4 inch

Voltmeter , Range 0 to 300 V dial 2.5 inch

Valve Key , Size 1/4 inch , 3/16 inch and 5/16 inch, Double Sided

Ampere meter , Range 0 to 5 Amp.

Leak dedector to detect CFC and HFCs , Leak detector with probe minimum 14 inch long made up of stainless steel and hose, LED Display, Leak alarm and able to detect CFC HFCs

Thermostatic Switch, LP and HP Cut Out, Overload Protector, Filters, Strainers and filter driers , Thermostatic Switch, LP/HP Cut Out, Overload Protector, Filters, Strainers and filter drier fitted on board

Model of Refrigeration Cycle , Model of Refrigeration Cycle

Model of Window Air Conditioner , Actual cut section model of Refrigeration cycle mounted on stand

Refrigeration Cycle Testing Rig , Vapour Compression refrigeration cycle demonstration equipments Compressor and Condensor with Expansion Valves and Capillary Expansion variable load in evaporator

Digital Anemometer , Vane Type Anemometer with digital display

Gas Charging Kit , fitted with compressor with pipe line

Model of Open type Refrigerant Compressor , Actual cut section mounted on base