Punjab Police Housing Corporation Limited Tender
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Punjab Police Housing Corporation Limited Tender
Eprocure
Opening Date13 Jun 2018
Closing Date26 Jun 2018
Tender AmountRefer Documents
Costs
EMD
₹ 3,12,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Summary
Construction of Prefabricated Barrack at Intelligence Hqrs.
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2018_DHA_17466_1Bid Award Id
ViewTender No
08/2018-19Tender Authority
Punjab Police Housing Corporation Limited ViewPurchaser Address
-Website
http://eproc.punjab.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Providing and fixing Gyp board wall cladding with rockwool insulation with GI section as base as per specifications.
13350
-
-
Stone / Tile Work
-
-
-
Floor Tiles : Providing and laying Floor Tiles of minimum thickness 8 mm of approved make and colour, laid to pattern as per drawing, set in rich cement mortar 1:4, min 20mm thick including cement slurry complete with oxalic acid wash. Joints to run continuous horizontally and vertically. Rate to include levelling of the existing floor if required. (The quoted rate should includes protecting the tile from polythence & POP covering as required .
-
-
-
600 x 600 mm ( Base cost Rs 72/- per sft ) Toilet area floors/Kitchen
2540
-
-
600 x 600 mm ( Base cost Rs 72/- per sft )Barrack Floor
5200
-
-
Wall tiles : Providing and fixing Wall tiles of approved shade over a base of 20mm thick cement plaster 1:3 (1 cement : 3 coarse sand) including laying tiles to approved pattern with grooves setting the tiles in cement slurry joints filled and finished with neat white antifungal grout as per requirement. Tile joints to have spaceers in between and to be finished with approved make tile grout in thickness as directed.
-
-
-
600 x 300 mm ( Base cost Rs 75/- per sft )
2000
-
-
Providing and fixing 19mm thick pre-polished Granite counters ,or fascias laid in 19mm thick bed of cement mortar 1:4 and jointed with cement slurry with pigment to match the shade of granite including rubbing mirror polishing, bevelling of edges etc complete at all levels having 300 mm jhalar . (allowing for necessary cutouts for fixing of wash basin, pipes, waste coupling etc.if & where required) Base Rate Rs 180/- per sft
100
-
-
False Ceiling
-
-
-
Gypsum Board Suspended Ceiling : P/F at all height false ceiling of 12.5 mm thick gypsum board including frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 22 mm and 37 mm at 1200 mm c/c to centre one flange fixed to the ceiling with dash fastner 12.5 mm dia x 40 mm long with 6 mm dia. bolts to the angle hangers of 25 x 25 x 0.55 mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45 mm x 15 mm x 0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick botton wedge of 80 mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450 mm centre to centre shall be fixed in a direction perpendicular to G.I channel with connecting clips made out of 2.64 mm dia. x 230 mm long G.I.wire at every junction including fixing the Lagyp gypsum board with ceiling section and perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre with 25 mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the Lagyp board with standard Lagyp easy joint compound (3 layer) , paper tapes, finisher amd two coats of primer suitable for gypsum board as per manufactures specification and also including the coat of making opening for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Architect & also including the cost of plastic emulsion paint with required finish of 2 or 3 coats as per satisfaction of engineer.
5500
-
-
Providing and fixing of false ceiling at all heights of 600x600x0.5mm/600x1200x0.5mm Metal Ceiling perforated tiles with Fleece Powder coated of 60 to 70 microne type OREO GI Laid in grid system.The frame work comprise of made of GI 120 GSM coating with minimum 0.3mm thickness main runner spaced at 1200mm centre to center securely fixed to the structural soffit by approved hangers at 1200mm maximum centres. Hangers (GI wire of 4mm dia) to be fixed by approved roof plug, level adjusters and screw etc. The last hanger at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees (with double stiching) to be interlocked between main runners at 600mm centres to form 1200x600mm modules. Cut across tees longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200mm cross tees. Perimeter trim to be wall angle secured to walls at 450mm maximum centres. Wall height of Cross toe 24mmx26mmx32mm and Main Runner 24mmx38mmx32mm complete in all respects as per specifications.
2510
-
-
Panelling And Cladding
-
-
-
Mirror Cladding : Providing & pasting 6 mm thk mirror on 12 mm thick BWP Ply including cutting , edge polish & pasting complete including GI/ hardwood frame work & 12 mm thick bison board cladding as & where required as per detail drawing .(Min size 5' x 4')
350
-
-
Doors / Shutters- Providing and fixing ISI Marked factory manufactured flush door shutter with vision panel non decorative type, core of block board construction with frame of Ist class hard wood and well matched Laminate both faces of shutter fixed in position including cost of chowkhat of hard wood as per architectural drawing and as approved by the Engineer-in-Charge before execution (including cost of fitting , cleats stops, wooden knobs & labour for fixing the fitting) complete in all respects.
-
-
-
DS (Single Leaf Solid Door) 900 mm wide & 2400 mm ht.
5
-
-
DS (Double Leaf Solid Door) 2000 mm wide & 2400 mm ht.
4
-
-
Single Leaf Door (1050 x 2400)
4
-
-
Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish .
1250
-
-
Applying pink primer on plastered /Gyp board (special quality) including prepration of surface knotting and stopping etc.
1250
-
-
Wall painting with plastic emulsion paint of approved brand and manufacturer to given an even shade (two coats).
1250
-
-
Storage
-
-
-
Full Height Storages : Providing & fixing Full Height Laminated storage as per drawing . The overall Structure made in 18mm thick MDF / Pre laminated board & back of storages with 6 mm thick MDF / pre laminated ply . Storages finished in 1 mm thick textured laminate from everywhere except outer back side of storages and also including all SS snap hinges, handles, locks etc & all necessary hardware as required. Shutter size varies between 375-450mm wide & 450 mm deep as required with reverse bull nose edge on top & bottom of shutter (for files, folders coats etc) with select shelves duly adjustable as required on metal stud supports with sleeves set in at intervals of every 375 mm height. PVC lipping on all edges with matching shade, including laminated skirting in approved shade with all hardware, magnetic catchers, tower bolts, etc complete as per detailed drawings. (Front elevation area to be measured)
600
-
-
Electrical Panel cabinet made with 18 mm MDF / Pre laminated ply, comprising of textured laminated carcass, shutters including air transfer grill of size 300 x 300 mm, hardware- 300mm high SS 'Ozone' pull handle, hinges, magnetic catchers .
64
-
-
Lockers : Providing and fixing cabinet made of 19mm water proof board and both side 1mm thick laminates on all visible faces of size 2'x7' equally divided in four partitions including joinery fitting complete in all respect including lockable shutter as per architectural drawing.
150
-
-
Slotted Angle Channel Rack : P/F MS Slotted angle channel rack of size 3'x7'x1'-6'' deep with five shelves of 14 gauge for storage in store room etc. complete made as per design with powder coated paint and as per directed by Architect .
15
-
-
Internal Signages
-
-
-
Toilet Signage: Providing and installing General office signages made out of 6 mm thick acrylic sheet with SS Stud, with vinyl slider on top, as desired. Complete with adhesive/ 3M double sided tape etc. (200 x 150 mm) (Base rate Rs 1800/-)
4
-
-
Luminous Fire extinguisher Signage: Providing and installing fire extinguisher signage at locations indiacted by the architect. Size signage to be 150mm X 75mm. (Base rate Rs 800/-)
4
-
-
Luminous Fire evacuation plans: Providing and installing, Luminous fire evacuation plans, as per architects layout, sandwitched in 4mm thk.acrylic panels and fixed with ss studs on to the location marked by th architect. (Base rate Rs 3200/-)
6
-
-
Push/ Pull signages for all doors (Base rate Rs 200/-)
12
-
-
Films & Graphics
-
-
-
Roller Blinds with 5% openness factor:- Supply & Installation of manually operated roller Blinds.HARDWARE; TOP TUBE : Made of extruded aluminium with 38 mm Dia. and wall thickness of 1.2 mm with spline adoptable to accommodate clutch of UNISOLIL/ACMEDA make.CLUTCH MECHANISM : Moulded plastic having self lubrication with Glass fibre reinforcement, having a minimum lifting capacity of 8 lbs weight capality - 8 lbs Head adoptability - 38 mm OPERATING CHAIN : PLASTIC / STEEL ball chain adoptable to the clutch pitch for smooth operation of blinds.LOCKING MEMBER : Plastic/ steel stop locks for limit setting adoptable to the steel chain.Bonding ( Fabric Tube ) : 30/36 mm wide double sided adhesive tape of 3M for strong holding capacity.SPRING BOOSTERS: provided as per the requirement Bottom Bar : aluminium extruded circular section with powder coated finish, having a Min. weight to be 365 gms / Rmt for a perfect fall of fabric to avoid warpage / floating. Ends are covered with end caps to give a perfect finish.FABRIC: - Screen fabric Roller Blinds WINFAB MAKE Composition: 30% polyester and 70% PVC.Openness factor - 5%, Weight 380 gms / sq mtr +/- 5%, thickness 0.53 mm +/-5%, Fire classification : NFPA NO.701-2004 TM#1,california administrative code Title 19 BS 5867 part 2 Type B. Width(mm) :183/250/300 Mesh/ IN : 52 * 48 Breaking strength: WARP = 1300 WEFT = 1200 Tear strength: WARP =20 WEFT = 20. color fastness : ISO 105 B02 grade B. Anti ultravoilet : 95%
480
-
-
TOILET CUBICLES
-
-
-
Size: 1110mm (L) X 1650mm (D) X 2400mm (H)
-
-
-
Providing and fixing of Compact laminate partitions & doors with the following specifications.
-
-
-
Intermediate Panel, Front Pilaster and Door:
-
-
-
Hardware and Fixing:
-
-
-
All pilasters are to be supported with Nylon (Polymide 6 with M12 treaded-rod inserted for stability) or Stainless Steel adjustable foot and anchored to the floor with SS screws.
-
-
-
The pilasters shall also be affixed with an aluminium door stopper incorporated with rubber strip to reduce noise effect.
-
-
-
The intermediate panels/dividers shall be mounted to the wall with thick aluminium U-channel section using S screws. The top rail of the system shall be 2mm thk,semi-round,heavy duty aluminium channel section fixed to the top of the pilasters with SS screws.
-
-
-
All aluminium channels will be anodized or epoxy coated.
-
-
-
Accessories :
-
-
-
Each cubicle will be provided with the following SS accessories -Door knob, Coat hook with rubber stopper, gravity or spring hinges and privacy thumb turn.
-
-
-
Thickness of Green Compact Laminate : 12mm thk
-
-
-
Colour of HPL boards - Green Design in single colour
-
-
-
Door size : 750 mm x 2300mm ( W x H )
-
-
-
Overall ht of cubicle : 2400 mm
-
-
-
Accessories :
-
-
-
a) Aluminium “U” Channel
-
-
-
b) Aluminium Door Stopper Channel
-
-
-
c) Aluminium H Section Top Rail with Wall Bracket
-
-
-
d) Nylon Coat Hook
-
-
-
e) Nylon Privacy Thumb turn c/w Occupancy Indicator
-
-
-
f) Nylon Door Knob
-
-
-
g)Nylon Hinges with Cover
-
-
-
h) Rubber Door Stopper Lining
-
-
-
i) S.S. Screws 304 G & P.V.C Wall Plugs
-
-
-
Make: Debo / Greenlam / Merino or eqv
12
-
-
HAND DRYER
-
-
-
Providing and fixing of Hand dryer of approved make with complete accessories, as per drawing and to complete satisfaction of the Engineer.
-
-
-
Make & Model : EH-22 ABS Moderate type Hand Dryer.(Euronics)/U-tec
2
-
-
Location : Hand Wash
-
-
-
LIQUID SOAP DISPENSER
-
-
-
Providing and fixing of Soap Dispenser of approved make with complete accessories, as per drawing and to complete satisfaction of the Engineer.
-
-
-
Location : Hand Wash Area
-
-
-
Series : ES 20 Table Top Soap Dispenser
-
-
-
Make : Euronics / Equivalent/U-tec
-
-
-
Location : Hand Wash
4
-
-
TISSUE PAPER HOLDER
-
-
-
Providing and fixing of Tissue paper Dispenser of approved make with complete accessories, as per drawing and to complete satisfaction of the Engineer.
-
-
-
Location : Hand Wash Area
-
-
-
Make & Model : EP02 S.Steel Paper Towel Dispenser
4
-
-
Location : Hand Wash
-
-
-
Supply & fixing of approved make starWhite Coloured Wall mounting constellation model European water closet 'P' trap outlet with 15 mm dia inlet Concealed cistern dual type to enable flushing pipe work concealed behind wall supporting CI / MS bracket with CP bolts and nuts, plastic seat cover of approved make & colour with rubber buffers, flap, CP hinges, CP bolts and nuts, all of approved make etc., complete.
-
-
-
Particular - B/R = Rs 8000 :- ARS-WHT- 39951
-
-
-
Wall mounted EWC
-
-
-
Concealed cistern
-
-
-
Control plate segment
-
-
-
Soft close seat cover
8
-
-
Supply & fixing of approved make C.P. health faucet 15 mm dia with stop valve, C.P flexible pipe, C.P. nozzle and hook etc., complete including C.P wall flange.
-
-
-
Particular/MakE:- ALD-565 (Jaquar)
-
-
-
Angular stop cock
-
-
-
Health Faucet
8
-
-
Supply and fixing of approved make starwhite Coloured wash basin with single lever basin mixer and brass nuts, 32 mm CP brass bottle trap of casted type, 40 mm OD PVC waste pipe class 3 ( 6 Kg/cm2 ) concealed in wall and taken upto the floor trap with necessary specials, 15 mm CP brass angular stop cock with wall flange with necessary fittings etc., complete.
-
-
-
Particular - B/R = Rs 4500
-
-
-
Code:-CNS-WHT-701 (Jaquar)
Under Counter Basin
-
-
-
Wash Basin: Counter top/under counter
-
-
-
Flexible tube
-
-
-
Bottle Trap
-
-
-
Waste Coupling:
-
-
-
Pair of Pillar Cock
-
-
-
Angular stop cock :
-
-
-
Basin faucet :
20
-
-
Providing, fixing, testing and commissioning of starwhite coloured urinal with Sensor including CP brass waste with dome type grating, CP cast brass bottle trap with extension piece and wall flanges complete.
-
-
-
Particular - B/R = 7500
-
-
-
Urinal : URS-WHT-13257
-
-
-
Urinal sensor :
-
-
-
Waste Coupling:
-
-
-
Bottle Trap:
9
-
-
Supplying, Installing, testing and commissioning of approved make 15mm CP shower unit comprising of CP 15mm dia Lever handled and Diverter button with CP spout,overhead shower set comprising of CP shower arm,rose etc.,complete with CP wallflanges. Flow rate - 6.55 LPM
-
-
-
Divertor / Shower Head / showe arm/Bath Spout: Make:-OHS-1999/OHS-CHR-1605
4
-
-
Supply, fixing and commissioning of Double bowl stainless steel sink with single Drain Board (Overall size 1550 x 510 mm) supported by C.I. / M.S. Brackets, C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chain rubber plug, including cutting and making good the wall / floors wherever required.
-
-
-
Particular - B/R = Rs 4000
-
-
-
SS sink :- SBSD 01
-
-
-
Sink Mixer : OPP-15173BPM
-
-
-
Bottle Trap : ALD-769L250x190
2
-
-
Supply, installation, testing and commissioning of storage type Water Heater of approved shade with copper container, glasswool insulation, stove enamlled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on inlet connection, 15 mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 5/8 kg/sqcm complete as required.cost should include all accessories as required for installation
-
-
-
a) Capacity 25 Litres
4
-
-
Make:- monza-ec
25 L Ivory GHWAMFSIV025 Havells / Jacquar
-
-
-
Supplying and fixing in position PVC floor trap of "P" trap for wet areas. Making proper connection with cement solvent joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position complete as required.
-
-
-
a) 110 mm inlet and 75 mm outlet.
16
-
-
b) 75 mm inlet and 75 mm outlet.
10
-
-
Supply & fixing of 5"X5" SS grating (heavy quality Chilly make cockroach trap) etc., complete. Make: Chilly
16
-
-
Supply & fixing of angle cock with wall flange etc., complete. Angular stop Cock: CON-053KN ( Jaquar)
55
-
-
Providing and fixing Frosted Glass urinal divider / partition (Jacquar Make)
7
-
-
CONCEALED IN WALL : providing and fixing chlorinated polyvinyl chloride ( CPVC ) pipes as per IS15778 ( ISI marked with the prior approval of EIC ) , having thermal stability for hot & cold water supply , including all CPVC plain & brass threaded fittings fixing the pipe with clamps at 1.00 m spacing including jointing of pipes & fittings , with one step CPVC solvent cement and testing of pipes complete as per direction of EIC.
-
-
-
CPVC SDR 11 pipe & fitting 16mm o/d
150
-
-
CPVC SDR 11 pipe & fitting 20 mm o/d
100
-
-
CPVC SDR 11 pipe & fitting 25 mm o/d
100
-
-
CPVC SDR 11 pipe & fitting 32 mm o/d
95
-
-
Providing ,stringing out SWR UPVC soil wase vent or antisponage pipes ISI marked as per ISI 13592 of approved make excluding lead jointing TYPE B
-
-
-
110 mm o/d pipe
250
-
-
Providing ,stringing out SWR UPVC soil wase vent or antisponage pipes specials ISI marked as per ISI 14735 of approved make excluding lead jointing i) 110 mm o/d pipe
-
-
-
single juction with door
35
-
-
Cowl
8
-
-
collar
35
-
-
p trap/ f trap
70
-
-
single y juction
35
-
-
double y juction
150
-
-
Providing and fixing in position PVC water storage tank tripple layer make as approved by the Engineer-in-Charge including hoisting and carriage complete with providing and fixing 15mm or 20mm i/d tanki nipple complete.
-
-
-
Tanks ( triple layer)
10000
-
-
Providing, fixing and jointing G.I. union coupling (of approved make with the approval EIC) as per IS 1879 in G.I. Pipe Lines. complete in all respects.
-
-
-
20 mm i/d G.I. Union
10
-
-
25 mm i/d G.I. Union
12
-
-
Providing, fixing and jointing ISI Marked Gun-Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on GI pipe lines laid in the ground or inside the buildings including all carriages complete.
-
-
-
20 mm i/d Gun-Metal peet valves (Heavy Pattern)
5
-
-
25 mm i/d Gun-Metal peet valves (Heavy Pattern)
8
-
-
Prefab huts
-
-
-
Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry/RCC in 15c.m. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres.
150
-
-
Earth filling under floors with surplus ordinary soil or soil containing gravel or kankar upto 40% excavated from foundation and taken only from outside the building plinth in 15cm layers including ramming, watering and consolidating lead upto 30 metres.
100
-
-
Disposal of surplus earth undressed available from excavation involving an average horizontal throw upto 2 (two) metres including loading and unloading complete in all respect as per direction of Engineer -in-charge upto a lead of 5 km.
25
-
-
Providing and laying sandy soil filling in 15cm layers including ramming, watering and consolidating lead upto 100 mtr. including the cost of carriage.
320
-
-
Cement concrete 1:5:10 with stone ballast 40 mm gauge in foundation and plinth using concrete mixer volumatric type.
40
-
-
Damp proof course 40mm thick of cement concrete 1:2:4 with 2 coats of bitumen 20/30 penetration at 1.65kg per sqm laid hot & sanded.
30
-
-
Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixture as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement, centring and shuttering in foundation and plinth.
15
-
-
Extra for using concrete mixer voluemetric type where not included in the rates.
40
-
-
Shuttering for faces of concrete foundation and foundation beams(vertical or battering).-
85
-
-
Cold twisted deformed (Ribbed/tor steel)bars fe-500 grade as per IS 1786-2008, for RCC works where not included in the complete rate of RCC including bending, binding & placing in position complete.(all dias of bars)
15
-
-
Base course of floor consisting of 100mm thick cement concrete 1:8:16 and 100mm sand filling.
760
-
-
First class burnt brick work laid in cement sand mortar 1:5 in foundation and plinth.
35
-
-
Providing and Fixing of Factory made UPVC approved colour CASEMENT (Openble) Door made of extruded Profile with wall thickness of 2.2mm(+ -0.2mm). Window Profile with hollow section with multi chamber, Frame (60mm X 55mm), Sash(60mmX102mm) T Profile(one vertical length between shutter.(60mm X 74mm). Glazing bead(34mmX20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. Making arrangement for fixing of hardware. EPDM gasket .1.2mm(+-0.2mm) thick, Galvanized steel frame(28mmX21.5mm), Sash (31mmX 27.5mm)T-Profile(27mmX17mm) to be inserted in required profile, Frame will be fixed to the wall with 8mm x100mm long fastners, 5mm thick glazing with approved make. Hardware: Casement Door handle made of Zinc Alloyed (approved colour powder coating), Corner striker, cylinder, Door transmission gear made of steel with multi point locking system with strikers. 3D hings of Zinc alloyed(white powder coating). And Door closer.
275
-
-
THREE TRACK SLIDING WINDOW.Providing and Fixing of Factory made UPVC approved colour Sliding window Three Track made of extruded Profile with wall thickness of 2.2mm(+ -0.2mm). Window Profile with hollow section with multi chamber, Frame (108mm X 45mm), Sliding Sash(39mmX75mm) Sliding Mesh Sash (25mm x58mm) Sliding Interlock(0ne vertical length in each Shutter) (45.5mm X 28mm) Glazing bead(20mmX18mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc. Making arrangement for fixing of hardware. EPDM gasket .1.2mm(+-0.2mm) thick, Galvanized steel frame(30mmX18mm) 2 nos, Sliding Sash (30mmX 18mm)and sliding mesh sash (26mmX10mm) to be inserted in required profile, Frame will be fixed to the wall with 8mm x100mm long fastners, 5mm thick glazing with approved make. Hardware: Sliding handle made of Zinc Alloyed (approved colour powder coating) with Transmission gear made of mild steel with multi point locking system./Touch lock, Steel roller system. Stainless steel wire, Drainage cap etc.
236
-
-
PREFAB STRUCTURE
-
-
-
Providing & Fixing in position M.S. hollow square / rectangular / round pipe structure made of different sizes as per structural drawing complete including cost of cutting, welding, grinding, painting and carriage to site complete fixed in position as per Architectural drawings and to the entire satisfaction of Engineer-in-charge.
320
-
-
Providing & Fixing of 50/84 mm PUF(polyurethane foam ) insulated thick Panel with 0.5mm Prepainted Galvanised Iron sheet both sides in 40±2 Kg Density. The PU panel shall be CFC( Chlorofluorocarbon)free and Zero Ozone depleting panel using N Pantane blowing agent & made out of continuous line running on uninterrupted power supply. Panel shall have pre coated GI sheet on both side of Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 240 mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per IS : 277 : 1992, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. The PPGI sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. The panels shall be vertically joined together by tongue and groove joints. The PU Foam shall be self-extinguishing, fire retardant type having minimum density of 40 Kg/Cu.mt (+, -2 Kgs).The centre to centre pitch of crest profile on top sheet should be between 250mm- 270mm to ensure proper water flow. The roof shall have a projection of minimum 300mm on all sides.
980
-
-
Providing & Fixing of 30/64 mm PUF(polyurethane foam ) insulated thick Panel with 0.5mm Prepainted Galvanised Iron sheet both sides in 40±2 Kg Density. The PU panel shall be CFC( Chlorofluorocarbon)free and Zero Ozone depleting panel using N Pantane blowing agent & made out of continuous line running on uninterrupted power supply. Panel shall have pre coated GI sheet on both side of Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 240 mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per IS : 277 : 1992, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. The PPGI sheet shall have plastic protective guard film of minimum 25 microns to avoid scratches during transportation. The panels shall be vertically joined together by tongue and groove joints. The PU Foam shall be self-extinguishing, fire retardant type having minimum density of 40 Kg/Cu.mt (+, -2 Kgs).The centre to centre pitch of crest profile on top sheet should be between 250mm- 270mm to ensure proper water flow. The roof shall have a projection of minimum 300mm on all sides.
1020
-
-
ELECTRICAL WORK
-
-
-
Wiring in PVC insulated copper conductor single core FR cable (ISI marked), 1100volts grade to be laid in existing PVC pipes/ casing & caping etc., complete with PVC Gang boxes (on surface) required for suitable number of ways, for electronic fan regulators (socket size), bell push, electronic buzzer, 3pin 6 Amp., 3pin 16/20 Amp. Sockets and 6 Amp./16/20Amp. Swithces (flush piano type accessories) etc. and including the cost of flush piano type switches/sockets, step type electronic fan regulator, copper wire and other petty material etc including the cost of painting as required:-
-
-
-
Wiring fan point without fan box in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade with step type electronic fan regulator.
30
-
-
Wiring light point in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade.
120
-
-
Wiring 3 pin 6 Amp. wall socket (Shuttered) point in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade complete with bonding to existing earth with PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade.
20
-
-
Wiring 3 Pin 6 Amp. Plug control comprising wall socket (shuttered) and switch including bonding to existing earth with PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq. mm, 1100volts grade complete.
50
-
-
S/E of Fittings:-
-
-
-
Supply & erection of of Decorative box type fitting, ceiling suspension type with CRCA housing, crompton make LTT8-20 or equivalent model of Philips /Wipro / Havells / EON/ legaro/ Halonix with 18/20 watt LED T8 tubular lamp, with aluminium housing, including making connections
15
-
-
Supply & erection of of Recessed/ Surface mounted slim LED Dounlighter 12 watt, in powder coated white finished housing, round/ square shaped, Crompton make, Cat. No. LSCSM/LSCRM-12W-CDL or equivalent model of Philips/ Wipro/ Havell's/ EON/ Legaro/ Halonix, including making connections.
30
-
-
Supply & erection of of Strapline linear LED fitting (25 watt per mtr) with extruded alumium housing complete with suitable driver as required complete with suspending hangers, if required, and making necessary connections, Legaro make, Cat. No. 50-S/ 50-R or equivalent model of Philips/ Crompton/ Wipro/ Havell's/ EON/ Halonix, including making connections.
22
-
-
Supply & erection of of decorative hanging lumonaire with high efficient COB in desired colour suitble for 14 watt LED direct fit lamp, Legaro make, Cat. No. LZTE 3030 or equivalent model of Philips/ Crompton/ Wipro/ Havell's/ EON/ Halonix, including making connections.
10
-
-
Supply & erection of of LED Spot Light with aluminium reflector, 7 watt, in powder coated white finished housing, round/ square shaped, Legaro make, Cat. No. LHR 6208 or equivalent model of Philips/ Crompton/ Wipro/ Havell's/ EON/ Halonix, including making connections.
20
-
-
S/E of Electric ceiling fans sweep Ortem/ Usha/ Crompton/ Havells make (Without regulator) capacitor type with double ball bearing, complete with 300mm down rod, canopies, shackles and suitable for operation on 230/240 volts 50 Hz single phase AC supply confirming to IS 374:1979 or 5 star rated, with latest ammendments including making connections and cost of petty material:
-
-
-
1200 mm sweep
30
-
-
Supply & erection of of heavy duty exhaust fans of following sizes propeller type (Crompton/ Khaitan/ Havell's make) complete with sheet metal impeller, mounting ring, MS arm, rubber cushion, totally enclosed motor epoxy powder coated, dynamically balanced blades suitable for operation on 220/240 volts single phase 50 cycles AC supply including making connections & cost of petty material.
-
-
-
300 mm sweep
5
-
-
380 mm sweep
4
-
-
Supply & erection of louver shutter for exhaust fans of following sizes, made of aluminium sheet with GI louvers, Cannon/ National make or as approved by Engineer in Charge.
-
-
-
300 mm sweep
5
-
-
380 mm sweep
4
-
-
Supply and erection of sheet metal double door distribution boards of suitable size and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles and bonding to existing earth etc.
-
-
-
Sheet metal double door T.P. & N. distribution board (dust protected) provided with bus bar, neutral link and din bar, suitable for incorporating FP/ TPN MCB's/ isolators for incoming and DP/ SP & N/ Single Pole MCB's/ RCBO/ RCCB's for outgoing 6 way each
2
-
-
Supply and erection of Miniature Circuit Breakers/ RCBO's/ RCCB's in the existing MCB distribution board as per PWD General Specifications 2010 including connections with suitable size of thimbles/lugs.
-
-
-
GROUP-B: (Havell's, HPL, ABB, Indo Asian & other brands approved by PWD)
-
-
-
Miniature circuit breaker single pole 6 to 32amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply
36
-
-
Miniature circuit breaker four pole 50, 63amp. (Breaking capacity 10kA, Curve-C) suitable for 240/ 415 volts 50cycles AC supply
2
-
-
PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:
-
-
-
Supply and erection of PVC insulated single core FR copper conductor cable ISI marked left bare in pipe or casing of suitable size excluding the cost of supply and erection of pipe or casing.
-
-
-
PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5 sq.mm, 1100volts grade.
1200
-
-
PVC insulated copper conductor single core FR cable (ISI marked) overall 2.5 sq.mm, 1100volts grade.
500
-
-
PVC insulated copper conductor single core FR cable (ISI marked) overall 6 sq.mm, 1100volts grade.
400
-
-
PVC insulated copper conductor single core FR cable (ISI marked) overall 10 sq.mm, 1100volts grade.
40
-
-
Supply & erection of PVC Casing & Caping for wiring purposes including inspection boxes etc., & other petty material:-
-
-
-
PVC casing & caping 25mm thick
200
-
-
Supply & erection of PVC pipes & HDPE pipes (fire retardant) for wiring purposes including bends, inspection boxes etc., where necessary including other petty material as per PWD General Specifications 2010:-
-
-
-
Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) On Surface
150
-
-
Heavy gauge PVC conduit pipe 32mm dia (On Surface)
75
-
-
Supply and erection of PVC flexible pipe complete without compression glands, locking arrangement, check-nuts as required :-
-
-
-
PVC flexible pipe 25mm dia.
300
-
-
PVC flexible pipe 32mm dia.
25
-
-
Earthing of Sheet metal/ iron clad Switches and metallic cases etc., with No. 7/14 S.W.G. (7/2.18mm dia.) G.I. wire in 20mm dia G.I. pipe partly recessed and partly on surface complete with 135cm long 50mm dia. G.I. earth pipe with G.I. reducing socket (50mm x 20mm) including erection of the same, 4 metre below ground level with necessary charcoal & salt mixture etc., up to 7 metre in length (including boring & refilling).
4
-
-
Earthing of metallic cases etc., with G.I. wire No. 7/14 S.W.G. (7/2.18mm dia.) in 20mm dia. G.I. pipe on surface including painting etc. (as additional length)
20
-
-
Supply and erection of double walled corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation (making necessary trench), placing the pipe in position and back filling with excavated soil etc. of the required size.
-
-
-
Double walled corrugated (DWC) HDPE pipe 50/ 38mm (outer/ inner dia.)
50
-
-
XLPE/ PVC INSULATED ARMOURED CABLES (LOOSE IN THE EXISTING TRENCH OR PIPE):
-
-
-
Supply & laying of aluminium conductor XLPE/ P.V.C. insulated armoured and served cable to be laid loose in the existing trench or pipe as per PWD General Specidications 2010:-
-
-
-
Aluminium conductor XLPE/ PVC insulated PVC sheathed armoured and served cable working voltage 1100volts grade 25sq.mm (3 ½ Core)
150
-
-
Supply and erection of sheet metal bus-bar chamber (factory fabricated) duly powder coated on existing surface with required no. of bus-bar strips of suitable length and cross-sectional area. Copper strips of suitable length and cross-sectional area should be tinned and mounted on DMC/ SMC moulds at sufficient distance enclosure made of M.S. sheet 1.6mm thick with hinged cover and lock, fitted with dust excluding gaskets and secured with sufficient no. of cadmium plated iron screws and of given overall dimensions and to be fixed with G.I. bolts and nuts/ rag bolts and nuts etc. complete with all accessories including connections with suitable size of thimbles, bonding to the existing earth and painting etc. as desired by the Engineer-in-charge at site.
-
-
-
Sheet metal bus bar chamber suitable for 100amp. 415 volts capacity with 4 tinned copper strip bus bars each of length 230mm and cross sectional area (25mm x 3.3mm) enclosure having over all dimensions (300mm x 345mm x 120mm) nominal
1
-
-
Supply and erection of MS perforated cable tray with DA gray paint on the existing surface with the help of MS angle iron support (to be painted with approved paint) of suitable size to be fixed with fastners/ nut & bolts etc. complete in all respect as desired by the Engineer-in-charge.
-
-
-
MS perforated cable tray size 150mm x 50mm x 50mm (2mm thick)
100
-
-
Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubicle type) in the existing Cubical Panel (conforms to IEC:60947-II) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD general specifications 2010 complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with sutiable size of Thimbles etc.
-
-
-
MCCB (Fixed Type Thermal and Magnetic Protection Make: L&T, ABB (T-MAX), Schneider (CVS), Seimens(3VT1/3VL))
-
-
-
100amp. 415 volts breaking capacity ≥25kA four pole fixed type thermal and magnetic setting MCCB unit
1
-
-
Supply & installation of Sheet Metal Enclosure for 4 pole MCCB, 100 Amp.
1
-
-
Supply & erection of MS Junction box Size 12"x6"x4" made of MS sheet 16 SWG duly painted, covered with bakelite sheet 3mm thick with help of brass screws and complete in all respects as desired by Engineer-in-charge.
2
-
-
Supply and erection of 20mm dia. heavy gauge welded conduit pipe (1.60mm thick) suspension rod for ceiling fan complete in all respect as desired by the Engineer-in-charge.
35
-
-
Supply and erection of 12mm dia M.S. fan hook, bolted/ welded with trusses, complete in all respect as desired by the Engineer-in-charge.
30
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements