Public Works Department Tender

Making 50 mm x 50 mm furrows Making 50 mm x 50 mm furrows 45 degree to the centre line of road and at one metre interval in the existing bituminous wearing coarse including sweeping and disposal of excavated material within 1000 meters lead complete as per technical clause 404 of MORT&H specifications.

Brick on End Edging Providing and laying of brick on end edging 6.83 cm wide, 11.11cm long and 22.86 high half brick deep including excavation, refilling and disposal of surplus earth up to 50 mtr complete as per Punjab PWD specifications.

Relaying of recovered material obtained from dismantled road material obtained from road crust compacting with vibratory roller to achieve the desired density, complete as per MORD technical specifications

Construction of granular sub-base by providing material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per MORD technical specifications

Water Bound Macadam Grading I (without screening for low volume Roads/undersigned Providing, laying, spreading and compacting stone aggregates of Grading I to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications

Water Bound Macadam Grading II (without screening for low volume Roads/undersigned Roads Providing, laying, spreading and compacting stone aggregates of Grading II to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheeled roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density complete as per technical specifications

Surface dressing Providing and laying surface dressing in single coat using crushed stone aggregates of specified size on a layer of bituminous binder VG-10 @ 1kg per sqm laid on prepared surface after cleaning the road surface and rolling with 8-10 tonne smooth wheeled steel roller complete as per technical clause 509 of MORT&H specifications.

Tack coat with Bitumen VG-10 Bulk Providing and applying tack coat with penetration grade bitumen VG- 10 using bitumen pressure distributor @ of 0.40 kg per sqm on the prepared bituminous surface/granular surface treated with prime coat after cleaning the surface complete as per technical clause 503 of MORT&H specifications

Open - graded premix Providing, laying and compaction of open - graded premix surfacing of 20 mm thickness consisting of crushed stone aggregates of specified grading premixed in a Continuous type hot mix plant with bituminous binder VG-10 @ 1.46kg per sqm, laid with Paver Finisher Mechanical and rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades complete as per technical clause 510 of MORT&H specifications

Seal coat Providing and laying of premix sand seal coat premixed in Continuous type hot mix plant using specified fine aggregates and penetration grade bitumen VG-10 @ 0.68kg per sqm, laid to the specified levels, grade and cross fall complete as per technical clause 511 of MORT&H specifications

Earth work undressed with a combined lead upto 2 meters including breaking of cloads and extra for laying earth/fly ash as per specification for compacation in 20 cm layers and dressing properly to desired site requirement. (No extra allownace of wetness, slush or numus dal are payable)

Road marking with hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 0.25kg per sqm area as per IRC:35 1997 complete as per technical clause 803 of MORT&H specifications as per CSR 24.57

Supplying and fixing of single mould twin shank reflective road studs made out of poly carbonate/ABS moulded body and reflective panels with micro prismatic lens or Glass Beeds capable of providing total internal reflection of the light entering the lens face with retro reflectance and chromaticity values shall be as given in the detailed specifications and the product shall conform to ASTM D4280. The raised pavement marker shall also meet all the testing conditions of ASTM D4280 and fixed to the road surface using the adhesive. Two cylindrical Polymer Shanks of not less than 20 mm diameter and not less than 30 mm length shall be molded in the RPM body. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280. The marker shall withstand flexural strength of 909 kgf force in accordance with ASTM D4280. Marker lenses shall be moulded of Polycarbonate or methyl methecrylate conforming to ASTM D788. The supplier shall provide a 2 years warranty for satisfactory field performance as per clause 804.7.3 of MORT&H 5th revision specifications. as per CSR 24.63

Construction of Hume Pipe Culvertas per design and drawing provided by Engineer-in-charge. Complete in all respect as per PWD specifications.

Videography of Proposed/Execute site of work of Link Roads before & after completion of work two times (stilling & video Job Work)

(-) D/d Credit of old useful serviceable materials like Brick Bats & Bricks which obtained from Dismantling of existing brick edging:-

(i) Brick Bat

(ii) Bricks

Add extra cost of Cutlural Cess @ 1% on Total cost as items mentioned above