Public Works Department Tender
If you want to inquire about any e-tender the Punjab government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Punjab tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Punjab etender you're looking for. Read further to learn how to search and bid for etender Punjab.
Costs
EMD
₹ 5,03,000Document Cost
₹ 20,000Tender Fee
₹ 5,900
Summary
Construction Of Additional Two Storey Third Floor And Forth Floor Of Block-b In Dac Complex At Moga Punjab Electrical External Special Services 1 No Lift Epabx
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_CEPW_125555_1Bid Award Id
ViewTender No
Bid No.32 dt 29.08.2024Tender Authority
Public Works Department ViewPurchaser Address
-Website
http://https://pwdpunjab.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Supply, installation, testing and commissioning of 1 No. lift of 13 passengers machine room less.
Type and Capacity : Approximately 884 Kg, 13 Passengers Speed:1.0 Meter per second Type of drive: AC Variable Voltage Variable Frequency with 16-Bit Microprocessor. Motor: Permanent Magnet Gearless Machine to be hoisted on the top of guide rail within the elevator hoist way Travel: Approximately 15 meter________ Serving: _5 Floors _5 Stops _5 Openings _5 Levels (All on the same side) Hoist way Required: 2050mm (Wide) x 2500mm (Deep) Clear dimensions Headroom Height (HR): 5000 mm beyond finished floor level of last landing Pit Depth: 1600mm below the finish floor level of first landing Car Size Area: Minimum 2.06 square meter and Maximum 2.20 square meter Car Enclosure: Constructed out of stainless steel Scratch proof Finish (Vandal Proof).
Car Entrance: Center Opening Automatic Doors with vision panel (Upto 40% area should be visible by glass) of Stainless steel finish panel in Scratch Resistance/ Vandal proof with a clear opening of 900mm (wide) x 2000mm (high) Door operation: Automatic DC Door operation with adjustable door opening and closing timings Control: Simplex full selective collective control with and without attentdent Operation: Automatic Power Supply: 415 Volts, 3- phase, 50Hz Alternating Current Flooring: Floor Skid - Resistant as per standard Fan: Blower Fan in Car for ventilation with Auto cut off Lighting: LED for Car Lighting Indicators: LED Dot matrix / Digital 3 segement direction and position indicators in the car and at all landings Hand Rail: Stainless Steel round Hand rail not less than 600mm long at 900mm above floor level (Side LH,Side RH & Rear) Call Button Height: Call button (Outside the lift) placed at a height between 800mm-1meter from the floor level Control Panel Height: Control panel placed at a height between 800mm-1meter from the floor level Std. Govt. features.
-
-
-
... More
Other Features: 1. Battery operated emergency light with rechargeable battery 2. Battery operated emergency alarm with rechargeable battery 3. Adjustable Guide shoes 4. Micro movement LED based buttons 5. Door Open and Close buttons 6. Emergency Intercom provided inside the elevator 7. Emergency Intercom usable without the voice communication 8. Load weighing device with overload bypass feature and Overload function with Audio Visual Indication 9. Steel items, door frames sill angle's, fascia plates, spring buffers
10. Automatic phase reversal device and Phase Failure protection
11. Call registration 12. Audio & Video System installted in the lift indicating arrival at a floor 13. Manual break lever 14. Additional car gate lock 15. Automatic break testing infrared safety curten 16. Braille Buttons (Inside and outside) with Braille instructions for the communication system 17. Kick plate/Skirting 18. Lift anoucement system to announce floor level's in english language only and indication of door for entrance / exit is either Open or Close 19. Car Operating Panel 20. Car plateform constructed out of cold rolled grain oreinted formed sheets of steel 21. Phase two device fire man drive 22. Fire Man switch at main lobby 23. Car false ceiling in stainless steel 24. Pit ladder 25. Anti Nuisance car call protection 26. Door Nudging 27. Automated Resuce Device to bring the elevator to the nearest landing in case of power failure.
28. The provision of mirror on the wall of the lift car opposite the lift door not extend below 900mm from the lift floor to avoid confusing people with impaired sight.
29. The emergency communication system should be coupled with an induction loop system installed all around the lift. Telephone units, where provided, should have an inbuilt inductive coupler to assist persons using hearing aids.
1
2440473
2440473
... More
XLPE INSULATED UN-ARMOURED CABLES (LOOSE):-
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-
-
-
-
... More
Overall size 16sq.mm (4Core) Un-armoured (Loose)
80
10535
131.69
... More
XLPE INSULATED UN-ARMOURED CABLES (ON SURFACE):
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:-
-
-
-
... More
Overall size 16sq.mm (4Core) Un-armoured (On-Surface)
50
7572
151.44
... More
DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:
Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-
-
-
-
... More
Double walled corrugated (DWC) HDPE pipe 63/51 mm (outer/ inner dia.)
70
10914
155.92
... More
COPPER EARTHING (8 SWG COPPER EARTHING): Earthing with 8 SWG (4mm dia.) electrolytic copper wire thimbled (1No. copper thimble with suitable size steel bolt, washers & double nut) with 30cm x 60cm x 2mm thick copper plate (made cylindrical) burried below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the copper wire run through 20mm dia. G.I. pipe (A-Class) recessed in wall and in floor etc., up to suitable Length in metre (including bore Length). G.I. pipe 20mm dia. (A-class) of suitable Length should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-
-
-
-
... More
Earthing with 8 SWG (4mm dia.) copper wire thimbled with 30cm x 60cm x 2mm thick copper plate burried 10.50 metre (34.44 feet) below ground level (up to 14metre in Length) with G.I. pipe 20mm dia. (A-class), 9metre long
2
22288
11144.34
... More
Additional Length copper wire 8 S.W.G. (4mm dia.) in 20mm dia. G.I. pipe (On Surface)
80
26076
325.95
... More
MCCB's (MOULDED CASE CIRCUIT BREAKER):
Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubicle type) in the existing Cubical Panel (conforms to IEC:60947-II) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD General Specifications (Electrical Works) complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with sutiable size of Thimbles etc.
-
-
-
... More
MCCB Four Pole 40amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting
1
6626
6626.73
... More
MS SHEET ENCLOSURE FOR MCCB's:
Supply & Erection of indoor type MCCB enclosure of suitable size having provision for MCCB with extended rotary handle. The Enclosure shall be made from 14/16 SWG CRCA sheet, confirming to IS 8623/1977-82. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The Enclosure door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. The Enclosure will be wall mounting type having provision for cable entry from bottom/top with cable glands etc. The sheet metal is sprayed with corrosion resistant etch primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work:-
-
-
-
... More
MS Sheet Enclosure having provision for MCCB 40-160Amp.with extended rotary handle (Approx. Size 500mm x 300mm x 200mm)
1
3342
3342.12
... More
SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's:
Supply and erection of sheet metal Double Door Distribution Boards IP 43- IK09 metal door (dust protected) as per IS 8623-1&3, IEC 61439-1&3 suitable for flush mounting with fully insulated copper busbars, shrouded neutral bars, earth bars, cement spill protector, colorcoded interconnecting wire set, cable ties, blanking plates and circuit identifications label and of required no. of ways for mounting miniature circuit breakers/ RCBO's/ RCCB's in the distribution board (For SP&N distribution board with provision DP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings and for TP&N horizontal distribution board with provision TPN/ FP MCB's/ RCCB's/ RCBO's as incomer and SP MCB's as outgoings) as per PWD General specifications including connections with suitable size of thimbles and bonding to existing earth etc:-
-
-
-
... More
SP&N Double Door Distribution Board 8 way each
1
1416
1416.27
... More
Supply and erection of sheet metal Cable End Box (Make is same as MCB Distribution Board) mounting on the top or bottom of the MCB Distribution Board (Either Horizontal or Vertical) to keep loose wires & cables as per PWD General specifications including petty materials etc as required:-
-
-
-
... More
Cable End Box for SPN 8 Way
1
679
679.3
... More
MINIATURE CIRCUIT BREAKERS:
Supply and erection of Miniature Circuit Breaker MCB's for circuit protection against overload and short circuit current fault suitable for 240/ 415 volts 50cycles AC supply with breaking capacity of 10kA, Curve-C and low watt losses as per IS/IEC 60898-1, energy limitation class-3, true contact indication, label holder facility in the existing MCB distribution board as per PWD General Specifications including connections with suitable size of thimbles/lugs:-
-
-
-
... More
MCB Single Pole 6-32amp. (10kA, Curve-C)
6
1143
190.58
... More
MCB Double Pole 6-32amp. (10kA, Curve-C)
1
580
580.27
... More
Providing EPABX System:
-
-
-
... More
Supply, installtion, testing & commisioning of the Switching system of the EPABX should be designed with IP at the core allowing fully distributed IP solutions across data networks in 19” Rack Mountable,7 universal slots in single Node and should support card Analog Extension Card , Digital Extension Card , for the respective addition / expansion. Analog & Digital extensions can be increased in the steps of 8, 16 & 32 Ports.Analog Trunks , PRI, BRI Trunks, E1 & SIP Trunks . Single card/module should support 2 or more PRIs, It should support 100% IP or 100 % TDM or a hybrid of IP/TDM technologies. The system should support IP Communication Devices (wired and wireless) e.g. IP Phones (Hard and Soft phones), Mobile IP Phones, multimedia PCs, SIP phones, Video phones (Hard & soft), etc.1.3. The system should also support Legacy TDM communication devices (Digital and analog 2 Wire telephone instruments with or without caller-id (Both FSK and DTMF), Fax, modems, ISDN phones etc. 1.6. The proposed system should support direct SIP integration with Microsoft Lync 2013 including following. Vendor should provide proper document towards certification with Microsoft Lync 2013 integration.1.16. The system should support at least 228 analog extensions in a single node and up to 600 analog Extensions in multiples nodes,at least 400 Digital Phones in a single node and 600 digital phones in multiple node,support at least 600 SIP extensions in a single node,Support 600 DECT/SIP DECT phones.support at least 224 DECT base stations and over 4000 SIP-DECT Base stations.should support minimum 56 Analog Trunks ,56 ISDN BRI trunks,14 PRI Trunks.Fax over IP with T.38 Interface and should support minimum 140 channels.240 SIP access channels.1.26. The system should have in-built Auto Attendant and 2 Port Voice Mail, Direct Inward System Access (DISA), Direct Outward System Access (DOSA) & Music On Hold (MOH). The system should be communication server should be on Leaders of Gartner Magic Quadrant. The OEM should be present globally minimum 70-75 countries. EPABX/Server, Digital Phone, IP Phone, cloud server must be from same OEM. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 15 years experience with same OEM & have already maintained services minimum 18-20 EPABX system in Punjab region. complete in all respect as per satisfaction of the Engineer in charge of the work.
1
159744
159744
... More
Supply, installtion, testing & commisioning of card 08 PNT Line (backup Lines) complete in all respect as per satisfaction of the Engineer in charge of the work.
1
41013
41013
... More
Supply, installtion, testing & commisioning of card 32 Analog Extensions complete in all respect as per satisfaction of the Engineer in charge of the work.
2
139492
69746
... More
Supply Installation Testing and Commissioning of the Sip Extension with its license for IP telephones complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.
10
39390
3939
... More
Supply Installation Testing and Commissioning of SIP Phone Up to 2 lines on dedicated line keys with LEDs 3 programmable keys that come pre-programmed and labeled with default values (Callers, Redial and Transfer) 4-way navigation with Select/OK key Dedicated function keys, including Transfer, Callers List, Hold, Redial, Goodbye, Options, 2 volume keys, Mute (with LED) and Speaker (with LED) Audio and Codecs,Hi-Q Audio . (HAC) handset,Full-duplex quality speakerphone,Wideband handset and speakerphone, Codecs: G.711 μ-law / A-law, G.729, G.722, AMR*, AMR-WB(G.722.2)*, G.726, iLBC, BV16, BV32, L16,Echo cancellation,Comfort noise utilization, Packet loss, concealment, Monochrome LCD ,2.75” 128x48 pixel graphical displa LED for call and message waiting indication,Security User and administrator level passwords for login Encryption of configuration files, HTTPS configuration downloaded and web managementPhone lock with PIN, Digest Authentication,Transport Layer Security (TLS), Secure Real-Time Protocol (SRTP),XML API Capabilities,RTP Streaming Control, CTI applications Dual 10/100 Mbps Ethernet ports with hardware based Ethernet switch Manual or Dynamic Host Configuration Protocol (DHCP) IP address setup Support of multiple DHCP options: 2, 12, 42, 43, 60, 66, 77, 120, 132, 159, 160 Time and date synchronization using SNTP, Quality of Service support – IEEE 802.1 p/Q VLAN and priority tagging, Type of Service (TOS), and Differentiated Services Codae Point Integrated HTTP/HTTPS server for web administration and maintenance including a built-in troubleshooting sectionMass deployment via central provisioning of user configuration files – TFTP, FTP, HTTP, HTTPSTR-069 support,PoE Class 1 Level “V” energy efficiency rated power adapters available complete in all respects as approved and desired by the Engineer-in-charge at site.
2
17516
8758
... More
Supply Installation Testing and Commissioning & Laying of Cat 6 Cable in existing conduit Category 6 Unshielded Twisted Pair 23 AWG:305mtr. ,4 pair 100W cable shall be compliant with ANSI/TIA/EIA-568-C.2 Additional Transmission Performance Specifications for 4-pair 100W Category 6Cabling. Tested upto 600 MHZ; Construction: 4 twisted pairs separated by internal X shaped, 4 channel, polymer spine / full separator. Half shall not be accepted.Sheath : FRPVC/LSZH,Outer Diameter 6.1 mm nominal;Temperature Range -20° to +60°C.Manufacturer should have ISO 9001:2008 Certification for Quality Management System.Manufacturer should have ISO 14001:2004 Certification for Environmental Management System.All UTP and Its Components should be from same OEM. complete in all respects as approved and desired by the Engineer-in-charge at site.
300
15000
50
... More
Supply Installation Testing and Commissioning of L2+ Managed Industrial Grade POE Switch 10 Ports Gigabit Managed Industrial Grade POE Switch , 8 10/100/1000 Base- TX portand 2 Gigabit SFP slotand 1console port Network Protocols: Support , IEEE802.3, IEEE802.3u, IEEE802.3z , IEEE802.3ab , IEEE802.3x , IEEE802.1d , IEEE802.1w , support IP camera should Working temperature:-40～75℃ Storage temperature:-40～85℃, Relative Humidity : 5%~95% (no condensation), Shell : IP30 protectgrade, metal shell Installation : DIN- Railor Wallmounts, MTBF : 300,000 hours, Support L2+ Switching features including 802.1Q VLAN, Mirroring, Portisolation, IGMP Snooping, DHCP Snooping, LLDP, IP Source Guard, ARP inspection, ACL setc. Support spanning tree STP(802.1D) and RSTP(802.1W).802.1s(MSTP) way exchange time 50ms Jumbo frames support upto 9.6 Kkilobytes Support enhanced managemen through WEB,CLI, TELNET, SSH, SNMP Ethernet port support 10/100/1000 Mself-adaption.Bandwidth: 24Gbps, Packet Buffer Memory: 4M Packet Forwarding Rate:1488000 pps /port Address Table : 8K complete in all respects as approved and desired by the Engineer-in-charge at site.
1
45138
45138
... More
Supply Installation Testing and Commissioning of Analog phone with caller id and hand free facility complete in all respects as approved and desired by the Engineer-in-charge at site.
64
87744
1371
... More
Supply Installation Testing and Commissioning of 20 Pair DB with Original Krone Module lock & key facility complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.
4
49512
12378
... More
Supply Installation Testing and Commissioning of 100 Pair MDF with Krone for EPBAX side with Original Krone Module lock & key facility complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.
1
43516
43516
... More
Supply, Installation Testing and commissioning of unarmoured 2 Pair 0.5 sq. mm copper conductor PVC insulated Cable for Telephones in existing Conduit complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.
800
25600
32
... More
Supply, Installation Testing and commissioning of armoured 20 Pair 0.5mm ABC conductor PVC insulated FRLS Cable for Telephones in existing Conduit complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.
300
99300
331
... More
Supply, Installation, Testing & Commissioning of 1 KVA UPS with Input power factor - 0.99, Output power factor - 0.8, OVCD inbuilt , DC V 36v, Efficiency : Above 90% complete in all respects as approved and desired by the Engineer in-charge at site.
1
13597
13597
... More
RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES):
Supply and erection of TV socket, Telephone socket and Networking socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module), covered with Frame Plate and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-
-
-
-
... More
Wiring Telephone socket point RJ11 (one module)
64
22735
355.24
... More
PVC, HDPE PIPES & PVC FLEXIBLE PIPES:
Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-
-
-
-
... More
Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
700
49560
70.8
... More
Providing Networking System along with allied accessories:
-
-
-
... More
Supply, Installation and Comissioning of Distribution Switch with minimum usable 24 10/100/1000BASE-T ports, 2 10GBASE-T ports , 4 10G SFP+ ports L3 Stackable Managed Switch with Redundant Power Supply Support.1 x RJ45 console port, RJ-45 port for out-of band-management port for accessing the CLI of the switch and USB port. 168 Gbps Switching capacity or higher or non-blocking architecture. 64 Bytes packet forwarding rate should be 125 Mpps or higher. Switch MAC table should be at least 16K or higher. Physical Stacking up to 9 units per stack. Stacking bandwidth up to 80G and up to 32 devices per virtual stack. Should have 802.1D STP, 802.1w RSTP and 802.1s MSTP Spanning Tree Protocol and ERPS as per standard ITU-T G.8032. BPDU Filter, BPDU restriction, Root restrction. Loopback detection (LBD). IGMP Snooping v1/V2/V3 & IGMP groups 1K or more IGMP groups and require support for IGMP Snooping Fast Leave. MLD Snooping v1/v2 & MLD group 1K or more and require support for MLD Snooping Querier. 16 L3 IP interfaces and IPv4/IPv6 Loopback interface. IPv6 Neighbor Discovery (ND). VRRPv3, Equal-Cost Multi-Path (ECMP) and UDP helper. Static route for both IPv4 and IPv6, OSPFv1, v2 & v3, RIP V1/V2/ng. Should have Policy-based Route (PBR). IEEE 802.1Q VLAN with different type of VLAN like Port based, Voice VLAN, Private, Double (Q-In-Q), Multicast VLAN (ISM VLAN for IPv4/IPv6), 802.1v Protocol VLAN ,VLAN Trunking. should have per-port broadcast, multicast, and unicast storm control to prevents faulty end stations from degrading overall systems performance. port security to secures the access port based on MAC address. Require prevention of DoS attacks, which include Land, Blat, TCP Null Scan, TCP Xmas Scan, TCP SYNFIN, Ping of Death Attack and TCP Tiny Fragment attack. DHCP snooping and DHCP server screening, DHCP server. 802.1X port based and 802.1X host based access control, Identity-driven Policy (VLAN, ACL or QoS) Assignment. RADIUS and TACACS+ authentication. Authentication database failover. QoS (quality of service) IEEE 802.1P for traffic prioritization. 8 queues per port. Different type of QoS priority like Strict Priority Queue and Weighted Round Robin, Strict + WRR, Congestion control using Weighted Random Early Detection (WRED) or WTD. Remark 802.1p priority, Remark ToS/DSCP and Rate limiting in Policy map. Support at least 2K ingress & 512 egress access control entries. ACL based on MAC, IPv4 and IPv6, TCP/UDP port number, User-defined packet contentm, CPU Interface Filtering. Able to manage trough Web-GUI, Fully functional CLI interface and Telnet. Should have multiple Image and configuration support to reduced down time for the switches. sFlow for monitoring traffic in data networks, SNMP v1, v2c, v3 and SNMP Traps and RMON. Support for DHCP Client support for IPv4/IPv6, DHCP server, DHCP Relay and DNS client. Should have SNTP/NTP protocol for time synchronization. CDP/UDLD, Link Layer Discovery Protocol (LLDP) and LLDP-MED.. CDP/UDLD, Link Layer Discovery Protocol (LLDP) and LLDP-MED. Operating temperature should be 0 to 50 ˚C. Switch should be EMI Certificates FCC, CE and Safety Certifications cUL/UL, CB. All Switches, Wireless and its Networkiing Components from Same OEM. OEM Should be International certification for the ISO 45001 Health and Safety Management System, Information Security Management System: ISO 27001, ISO 9001 Quality Management System, ISO 14001 Environmental Management System, and ISO 14064-1 Greenhouse Gas Inventory Standards. OEM should have Indian based operation at least for a period of 20+ years and should have an Annual Turnover of Rs. 500 Crores and above in any of last three consecutive Audited Financial years. (To ensure only principal networking companies participate having strong Product , Support and Service.) complete in all respect as per satisfaction of the Engineer in charge of the work.
4
537580
134395
... More
Supply, Installation and Comissioning of CAT 6 Cable should be Unshielded twisted pair cabling system, TIA / EIA 568-C.2 Category 6 Cabling system.Conductors should be 23 AWG solid bare copper.Netowork support should be ultrahigh speed data networks such as Gigabit Ethernet (1000 Base-T and 1000 Base-TX) and beyond.Cable Should be ETL/UL Certificates are mandatory.Frequency tested up to should be 600 MHz minimum.Impedance should be 100 Ohms + / - 15 ohms.Box Packing shoud be 305M.Should be 25-year systems warranty; Warranty to cover Bandwidth of the specified and installed cabling system, and the installation costs. Site certificate Should be issued by OEM.Should be RoHS compliant. complete in all respect as per satisfaction of the Engineer in charge of the work.
900
45000
50
... More
Supply, Installation and Comissioning of Patch Panel should be made of cold rolled steel.Should conform to TIA / EIA 568-C.2 Component Compliant.Should terminate 24 UTP CAT 6 (4 pair) Cables.Should confirm to EIA/TIA 568A wiring Pattern.Each port Should be features the spring-loaded shutter.Should be prevents incomplete mating Should be protects from dust and contaminants.Should be Front and rear port labelling as well as panel identification label.Should be Integral cable management shelf ensures bend radius compliance.Operating Life should be minimum 750 insertion cycles.Should be RoHS compliant.complete in all respect as per satisfaction of the Engineer in charge of the work.
4
32716
8179
... More
Supply, Installation and Comissioning of Patch Cord 1 Mtr Patch cord Should be 4 Pairs 24 AWG copper cables.The Outer Jacket should be Low Smoke Zero Halogen.24 AWG stranded bare copper.Operating temperature range should be -20°C to 60°C.Should minimum comply with proposed ANSI/TIA/EIA-568-C.2.Should be verified by ETL (ETL certificate to be enclosed with the Bid)UL listed (UL certificate to be provided along with the Bid)Should Have cross separator.Standard length should be available 0.5M to 10M.Should be RoHS compliant. complete in all respect as per satisfaction of the Engineer in charge of the work.
96
17568
183
... More
Supply, Installation and Comissioning of atch Cord 2 Mtr. Patch cord Should be 4 Pairs 24 AWG copper cables.The Outer Jacket should be Low Smoke Zero Halogen.24 AWG stranded bare copper.Operating temperature range should be -20°C to 60°C.Should minimum comply with proposed ANSI/TIA/EIA-568-C.2.Should be verified by ETL (ETL certificate to be enclosed with the Bid)UL listed (UL certificate to be provided along with the Bid)Should Have cross separator.Standard length should be available 0.5M to 10M.Should be RoHS compliant complete in all respect as per satisfaction of the Engineer in charge of the work.
78
16224
208
... More
Supply, Installation, Testing and Commissioning of 42U Network Rack Enclosure Frame-600X800-STEEL with accessories like fan, pdu, cable manager etc. Supply of 42 U Enclosure Frame-800X1000-STEEL, Caster Wheels Set of 4 (2 with Brakes & 2 without Brakes),Adjustable Levellers set of 4, Glass Door-800-42U, Metal Door-800-42U-Vented, Side Panels-1000-27U-Vented, Mounting Hardware-(Pack of 20), FHU with 4 FAN 360CFM, Vertical Power Distribution Unit with 12 x 5/15 sockets Round Pin, 230 Volts AC, 32 Amp with Plug, Vertical Cable Manager-42U-Loop, Horz. Cable Manager-1U-Loop, Conforms to DIN 41494 OR equivalent ISO Standards, Adjustable 19” equipment mounting verticals provide the better mounting flexibility maximizing the usable mounting space, Depth adjustable mounting slots, Top and bottom Panel with ventilation and cable entry facility, Provision to mount the cooling fans on the top panel, Powder coated finish with pretreatment process meeting all industry standards, Grounding and Bonding Options can be provided, 100% assured compatibility with all equipment conforming to DIN 41494. General industrial standard for equipment, Conforms to DIN 41494 or equivalent standard, Welded Frame, Lockable Toughened Glass Door, Metal Vented Door Steel, DIN Standard 10mm Sq. Slots / Direct M6 Tap, 19” Mounting angles made of formed steel Powder Coated, Welded to Frame, Vented and Field Cable entry exit cut outs complete in all respect as per satisfaction of the Engineer in charge of the work.
1
11706
11706
... More
Supply, Installation, Testing and Commissioning of Wall Mount 15U x 600 W x 600 D ,Front Glass Door (tinted,Toughened) with Lock & Key, 2 pairs of 19" Mounting Rails with U-Marking , Welded Side Walls, Min Accessories : 1U Cable Manager (1), Hardware Packet (1 Pkt), 6 Socket 5 Amp. Power Distribution Unit (1 No), Roof Mounted Fan Unit / 90 CFM /230V AC.as per DIN 41494 Standards complete in all respect as per satisfaction of the Engineer in charge of the work.
2
105846
52923
... More
Supply, Installation, Testing & Commissioning of 1 KVA UPS with Input power factor - 0.99, Output power factor - 0.8, OVCD inbuilt , DC V 36v, Efficiency : Above 90% complete in all respects as approved and desired by the Engineer in-charge at site.
2
27194
13597
... More
RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES):
Supply and erection of TV socket, Telephone socket and Networking socket points in powder coated/anodized concealed metal boxes recessed in wall required for suitable number of modules (Modular accessories) for having TV sockets, Telephone sockets RJ11 & Networking socket RJ45 (one module),covered with Frame Plate and other petty material etc., including the cost of above material, cutting and filling up of chases (with finishing the surface):-
-
-
-
... More
Wiring Networking socket point RJ45 (one module)
78
35991
461.43
... More
PVC, HDPE PIPES & PVC FLEXIBLE PIPES:
Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-
-
-
-
... More
Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
800
56640
70.8
... More
Providing CCTV System:
-
-
-
... More
Supply, erection, testing & commissioning of IP indoor Camera Image Sensor 1/2.8" Starvis Back-illuminated CMOS Sensor Resolution 2MP 1080 P Effective Pixels 1945(H)*1097 (V) Compression H.264/H.264+/H.265/H.265+/ JPEG/AVI /MJPEGTV System PAL/NTSC Electronic Shutter Time Auto: PAL 1/25-1/10000 Sec; NTSC 1/30-1/10000 Sec Minimun Illumination 0.005Lux S/N Ratio≥52dB Scanning System Progressive Video Output Network Reset Button Optional Focus Length 2.7-13.5mm Motor Zoom Focus Control Auto Lens Type Auto Pixels 2MP Infrared LED No, Support Warm light LED 4000 K, up to 30m Infrared Distance IR Status Auto Control IR Power On Smart, Manual & Timed mode Ethernet RJ-45 (10/100Base-T) Protocol TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP ,PP PoE, NTP, SMTP, UDP, SNMP ON VIF Support ON VIF 19.12(Profile S/T/G)P2P YES, Support QR Code POE Optional, Support IEEE 802.3 af Video Delay 0.3S (Within the Lan) Main Stream 12304*1296@25fps, Main Stream 21920*1080@30fps, Main Stream 31280*720@30fps, Sub Stream 11280*720@30fps 720*480@30fps Sub Stream 2352*288@30fps Tri Stream1280*720@30fps 720*480@30fps 352*288@30fps IE Brower IE8-11, Google Chrome, Firefox , Mac Safari Smart Phone iPhone, iPad, Android, Android Pad Intelligent Analysis Face Detection, Intrusion Detetion, Line Cross Detetion, Loiter Detetion, People Gather Detecion, motion detection based on human detection Day/Night Color/ B&W (IR-CUT )Image Config Saturation /Brightness/Contrast /Sharpness, Mirror, 3D NR , White Balance, FLK (Flicker Control), Video Tampering, HLC, Distortion Full Stat light Corridor Pattern Defog Mode ROIBLC WDR HDR: 120dB Motion Detection Support Privacy Masking 3 Rectangular Zone Recording Mode NVR/CMS/ Web Audio Optional 1 Built-in MIC Alarm Optional 1 Channel Input / Ouput SD Card Slot Optional Internal, Support Max 512GB RS485 Housing Metal ,IP67 , Contactor shall off load the work to OEM & have its own registered office in Punjab for sale & support of product. Camera & NVR should be from same OEM. IR Cut Filter Operation Temperature-20℃ ~ +60℃ RH95% Max Storage Temperature-20℃ ~ +60℃ RH95% Max Power Source DC12V±10%, 1000mA Dimension￠128 x 108(H)mm. Camera Should be BIS certified. Awared company must have minimum 5 years work experiance in networking & CCTV. Also have completed the similar amount of awarded job.complete in all respect as per satisfaction of the Engineer in charge of the work.
10
231250
23125
... More
Supply, erection, testing & commissioning of 5MP Outdoor Face Detection IP Network Camera Image Sensor 1/2.8" Starvis Back-illuminated CMOS sensor Resolution 5MP Effective Pixels 2616 (H)*1964 (V) Compression H.264/ H.264+/ H.265/ H.265+/ JPEG/ AVI /MJPEG TV System PAL/NTSC Electronic Shutter Time Auto: PAL 1/25-1/10000 Sec; NTSC 1/30-1/10000 Sec Minimun Illumination 0.01Lux S/N Ratio ≥52dB Scanning System Progressive Video Output Network Reset Button Optional Lens Focus Length 2.7-13.5mm Motor Zoom Focus Control Auto Lens Type Auto Pixels 4MP Night Vision Infrared LED No, Support Warm light LED 4000K, up to 40m IR Status Auto Control IR Power OnSmart, Manual & Timed mode Network Ethernet RJ-45 (10/100Base-T)Protocol TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP ,PPPoE, NTP, SMTP, UDP, SNMP ONVIF Support ONVIF 19.12 (Profile S/T/G)P2P YES, Support QR Code POE support, Support IEEE 802.3af Video Delay 0.3S (Within the Lan) Main Stream 12592*1944@30fp Main Stream 22560*1440@30fp Main Stream 31920*1080 @30fps 1280*720@30fps Sub Stream 11280*720@30fps720*480@30fps Sub Stream 2352*288@30fps Tri Stream 1280*720@30fps 720*480@30fps 352*288@ 30fps IE Brower IE8-11, Google Chrome, Firefox , Mac Safari Smart Phone iPhone, iPad, Android, Android Pad AI Function Intelligent Analysis Face Detection, Intrusion Detetion, Line Cross Detetion, Loiter Detetion, People Gather Detecion, motion detection based on human detection Day/Night Color/ B&W (IR-CUT ) Image Config Saturation/Brightness/Contrast /Sharpness, Mirror, 3D NR , White Balance, FLK (Flicker Control), IP camera should be compatible with network video recorder Video Tampering, HLC, Distortion Full Color Corridor Pattern Defog Mode ROIBLC WDR HDR: 120dB Motion Detection Privacy Masking 3 Rectangular Zone Recording Mode NVR/CMS/Web Interface Audio Optional 1 Built-in MIC Alarm Optional 1 Channel Input/Ouput SD card Support Max 512GB Housing Metal, IP67 Contactor shall off load the work to OEM & have its own registered office in Punjab for sale & support of product. Camera & NVR should be from same OEM. IR Cut Filter Operation Temperature-20℃ ~ +60℃ RH95% Max Storage Temperature-20℃ ~ +60℃ RH95% Max Power Source DC12V±10%, 1000 m A Dimension 268(W) x 95(H) x 88(D)mm. Camera Should be BIS certified. Awared company must have minimum 5 years work experiance in networking & CCTV. Also have completed the similar amount of awarded job. complete in all respect as per satisfaction of the Engineer in charge of the work.
1
24978
24978
... More
Supply, erection, testing & commissioning of PoE Spliliter 12 volt, 1 Amp, IP66 For High Voltage Protection complete in all respect as per satisfaction of the Engineer in charge of the work.
11
15037
1367
... More
Supply, erection, testing & commissioning of NVR shall have 16-channel video input. NVR shall be Embedded Linux. NVR shall support the following bandwidth - Incoming 112 Mbps and outgoing 96 Mbps. NVR shall support Video Output: HDMI (1 1024*768, 1280*720, 1280*1024, 1440*900, 1920*1080, 3840*2160/EDID), VGA (1024*768, 1280*720, 1280*1024, 1440*900, 1920*1080). NVR shall offer the following recording resolution streams Video Resolution: 8MP, 5MP, 3MP, 2MP(1080P), 1.3MP(960P), and 1.0MP(720P). NVR shall support Motion Detection. NVR shall support 4 zones of Privacy Mask. NVR shall offer intelligent analysis functions powered including Human and Vehicle Detection, Perimeter Intrusion Detection, Line Crossing Detection, Stationary Object Detection, Crossing Counting, Heat Map, Crowd Density Detection, Rare Sound detection (gunshot/baby crying/dog barking), Face Detection. NVR shall support G.711A/G.711U Audio compression. NVR shall integrate Audio input 1 CH RCA port. Video Recording and Playback. NVR shall have 2HDDs Slots. NVR shall support a 1-30fps Video Frame Rate. NVR shall have Record Mode: schedule, event-based - motion, I/O, PIR. NVR shall offer 16 CH max sync playback. NVR shall be able to playback according to different types, including Playback Mode Instant playback, Local video, and local image. NVR shall support Record Search Time, calendar, channel search, and event search, (ANR, regular video, motion detection video, alarm video, intelligent detection video). NVR shall support the following Video Playback: Start, stop, normal play, back play, frame-by-frame forward, full screen, Fast forward / backward (2x, 4x, 8x,16x), Slow forward (1/2x, 1/4x, 1/8x,1/16x), Add custom/Default Tag, digital zoom, video clip, sub-stream/main-stream, playback video bar, scale of 30 mins to 24 hrs. Storage and Backup. NVR shall offer USB mobile hard disk, U disk, and network backup Methods. NVR Should support FTP for uploading alarm video. NVR shall ANR Support Smart IPC (with SD card) ANR. Function. NVR shall support the following protocols: IPv4, IPv6, TCP/IP, HTTP, HTTPS, DDNS, RTMP, SMTP(SSL), SNMP, DHCP, PPPoE, UPnP, NTP, P2P, FTP, IP filter. NVR shall support ONVIF Profile S Support. NVR shall support ONVIF/RTSP/HTTP/HTTPS/RTMP port customized. NVR shall support Mobile Surveillance Support Apple, Android & Internet Explorer Support IE, Chrome, Firefox, and Safari. NVR shall have Digital Zoom support. NVR shall have IPC timing Manual/auto/timing/reconnect timing. Approved makes bosch, mountxross, axis, pelco shall support the following Event Actions: pre and post-recording, Sending an email, showing a message, sending an email, FTP upload video or screenshot, Cloud upload video or screenshot, full screen, voice prompts, Alarm output trigger, PTZ linkage. NVR Should support a combination of different events for effective alarm trigger and response. NVR Shall have exception alarms on event type of no space on disk, disk error, and video loss. NVR Shall be able to configure covert on camera by which recording is happening, but the live view is restricted. Network Detection monitoring, Utilization of total and used bandwidth, IP filter with blacklist and whitelist. NVR makes bosch, mountxross, axis, pelco Shall support video cover privacy mask both on live and recording up to 4 areas. NVR shall have User Management User add, delete, modify, permission management, and support. NVR Shall be able to trigger PTZ presets on any camera AI event. NVR shall support Security Mode authorized username and password, HTTPS with a password, and RTSP Validation. NVR should Manage IPC Support IPC centralized management, including IPC parameter configuration, information export and import, real-time information acquisition and upgrade. NVR shall have Statistics of events for face recognition, vehicle & and human, cross count, and heat map. Network Interface. NVR shall integrate 1 X RJ45 10M/100M/1000M adaptive Ethernet port. NVR shall integrate 1* RS485,& USB2.0*1(front) USB3.0*1+USB2.0*1(rear). General. The power consumption shall be 12V/2A and power Consumption ≤12W (Without HDD). Operation Temp./ Humidity -10°C ~ 55°C/10%-90% complete in all respects as approved and desired by the Engineer-in-charge at site.
1
46264
46264
... More
Supply, erection, testing & commissioning of L2+ Managed Industrial Grade POE Switch 10 Ports Gigabit Managed Industrial Grade POE Switch , 8 10/100/1000 Base- TX portand 2 Gigabit SFP slotand 1console port Network Protocols: Support , IEEE802.3, IEEE802.3u, IEEE802.3z , IEEE802.3ab , IEEE802.3x , IEEE802.1d , IEEE802.1w , support IP camera should Working temperature:-40～75℃ Storage temperature:-40～85℃, Relative Humidity : 5%~95% (no condensation), Shell : IP30 protectgrade, metal shell Installation : DIN- Railor Wallmounts, MTBF : 300,000 hours , Support L2+ Switching features including 802.1Q VLAN, Mirroring, Portisolation, IGMP Snooping, DHCP Snooping, LLDP, IP Source Guard, ARP inspection, ACL setc. Support spanning tree STP(802.1D) and RSTP(802.1W).802.1s(MSTP) way exchange time 50ms Jumbo frames support upto 9.6 Kkilobytes Support enhanced managemen through WEB,CLI, TELNET, SSH, SNMP Ethernet port support 10/100/1000 Mself-adaption.Bandwidth: 24Gbps, Packet Buffer Memory: 4M Packet Forwarding Rate:1488000 pps /port Address Table : 8K complete in all respects as approved and desired by the Engineer-in-charge at site.
1
45138
45138
... More
Supply, erection, testing & commissioning of Access Switch 24 10/100/1000BASE-T PoE and 4 100/1000 Mbps GbE/SFP combo ports, IEEE 802.3az Energy Efficient Ethernet (EEE),IEEE 802.3x Flow Control, IEEE 802.3af/at compliance (for PoE ports),9K Jumbo frame,256 Multicast Groups,802.1W RSTP, 802.1s MSTP, IGMP Snooping, Loopback Detection, 802.3ad Link Aggregation, Auto Surveillance VLAN, 802.1p Quality of Service with 8 queues per port,Supports 4 IP interfaces,Min 124 static route entries, Min 768 ACL Rules, SSH, TLS,DoS attack prevention, 802.1X Port-based Access Control, Port Security, Cable diagnostics, Dual image, Dual configuration, NMS Bundled along with Switch,OEM Should be present in Gartner Magic Quadrant from past 5 Years complete in all respects as approved and desired by the Engineer-in-charge at site.
1
50282
50282
... More
Supply, erection, testing & commissioning of Wall Mount 9U Rack ,Front Glass Door (tinted,Toughened) with Lock & Key,2 pairs of 19" Mounting Rails with U-Marking,Welded Side Walls With Metal Logo,1U Cable Manager (1), Hardware Packet (1 Pkt),6 Socket 5 Amp. Power Distribution Unit (1 No),Roof Mounted Fan Unit / 90 CFM /230V AC (1 No) complete in all respects as approved and desired by the Engineer in-charge at site Make DLink/Netrack/Mountxross complete in all respects as approved and desired by the Engineer in-charge at site.
2
18070
9035
... More
Supply, erection, testing & commissioning of HDD Formatted capacity 6 TB, Data transfer rate (max) Buffer to host Host to/from drive (sustained) 6 Gb/s 171 MB/s, Cache (MB) 64, Rotational speed (RPM) IntelliPower, Load/unload cycles4 300,000, Non-recoverable read errors per bits read 1 in 1014,Operating (2 ms, read/write) 30,Operating (2 ms, read) 65, Non-operating (2 ms) 250,Average power requirements (W) Read/Write 5.90, Idle 4.90, Standby and Sleep 0.40 complete in all respects as approved and desired by the Engineer in-charge at site.
1
22082
22082
... More
Supply, erection, testing & commissioning of Display : 50 inch, 4K (3,840 x 2,160), Direct LED, Professional Display with 4K Processor, Native Contrast ratio 5,000:1 or higher, Response time 12 ms or lower, Brightness 400 cd/m² or higher, 24/7, Portrait/Tilt functionality, HDMI Auto wake up, HTML5 platform, 16GB On Board Storage, HDMI*4 with HDCP 2.3 / RS232 / USB / RJ45 / Wi-Fi Direct / 20W Speakers / Android OS or similar, Viewing angle 178 degree, Apple AirPlay & Chromecast.complete in all respects as approved and desired by the Engineer-in-charge at site.
1
82027
82027
... More
Supply, Installation, Testing & Commissioning of Category 6 UTP, 4 Pair This cable well exceeds the requirements of TIA/EIA-568-C.2 and IEC/ISO 11801. Construction: 4 twisted pairs separated by cross separator, 4 channel, polymer spine / full separator. Half shall not be accepted, Operates at bandwidth of 250 MHz, Conductor Solid Bare Electronic Grade Copper. Inner jacket should be PVC and outer should be PE, suitable for direct burial. Insulation: Polyethylene, Attenuation ( 36 db/100m), Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR., Nominal Outer Diameter of Cable should be 9.70 mm and Conductor Diameter 0.56 mm (23 AWG), Cable should support operating Temperature from -20° to +60°C, Cable should come with printed sequential Length Counter on each meter, Cable support Conductor Resistance 93.5 OHMS/1000MTR@20 Degree, Mutual Capacitance of cable should be 5.6nF/100m, Max Resistance Unbalance of cable should be 5% Max, Capacitance Unbalance of cable should max 330pF/100m, Cable support Delay Skew: 45nS, Operating Voltage: 72V and NVP: 69%, Shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 250MHz.complete in all respects as approved and desired by the Engineer in-charge at site.
450
22500
50
... More
Supply, Installation, Testing & Commissioning of 6 Mtr HDMI Cable for NVR, UL Listed complete in all respects as approved and desired by the Engineer in-charge at site.
1
1714
1714
... More
Supply, Installation, Testing & Commissioning of 1 KVA UPS with Input power factor - 0.99, Output power factor - 0.8, OVCD inbuilt , DC V 36v, Efficiency : Above 90% complete in all respects as approved and desired by the Engineer in-charge at site.
2
27194
13597
... More
PVC, HDPE PIPES & PVC FLEXIBLE PIPES:
Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-
-
-
-
... More
Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
350
24780
70.8
... More
Providing Fire Detection/ Emergency Evacuation & PA System:
-
-
-
... More
FIRE PANELS & ANNUNCIATORS:
-
-
-
... More
Supply, installation, testing & Commissioning of Microprocessor based 1-Loop True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event , 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 300 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature will offer Redundant CPU. Four access levels, flash EPROM, Panel should be capable to work 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall support with Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on same peer-to-peer Network and 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. The panel shall be capable of self programing without any dependancy on dongle or programming software. Quoted rate shall include supply of necessary software & hardware for progamming the panel with all necessary licence. Panel shall have Modbus/ Bacnet over IP protocol for future integration with BMS. However, for present arrangement FA system will be standalone with 24x7 monitoring. The panel shall be capable for remote accessibility on a mobile app through cloud platform/solution. Designed to meet UL864, 10th The solution should be from single OEM. OEM should have manufacturing facility in India. OEM Should have presence in India from last 15 year. OEM should have own toll free number for service & support of product. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 2 trained OEM certified engineers & distributor have its own registered office in Punjab.complete in all respects as approved and desired by the Engineer in-charge at site.
1
264684
264684
... More
Supply, installation, testing & Commissioning of Inbuilt automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition with the charging capacity of 200AH with Emergency evacuation Control Panel & Digital Voice command system with Battery Dress Panel. The solution should be from single OEM. OEM should have manufacturing facility in India. OEM Should have presence in India from last 15 year. OEM should have own toll free number for service & support of product. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 2 trained OEM certified engineers & distributor have its own registered office in Punjab complete in all respects as approved and desired by the Engineer in-charge at site.
1
51709
51709
... More
Supply, installation, testing & Commissioning of Paging Microphone compatible with Emergency evacuation Control Panel Project specific OEM authorization required for executing agency complete in all respects as approved and desired by the Engineer in-charge at site.
1
26276
26276
... More
Supply, installation, testing & Commissioning of Addressable Smoke/Multi-criteria Photo-Thermal Detector and base with sensitivity range of 0.5 to 4.0% obs/ft.The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. Designed to meet UL268, 7th Edition complete in all respects as approved and desired by the Engineer in-charge at site.
88
346632
3939
... More
Supply, installation, testing & Commissioning of Reponse Indicator for up side of ceiling complete in all respects as approved and desired by the Engineer in-charge at site.
10
7730
773
... More
Supply, installation, testing & Commissioning of Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device complete in all respects as approved and desired by the Engineer in-charge at site.
6
25776
4296
... More
Supply, installation, testing & Commissioning of Addressable Fire Fighter's Telephone Jack for two way communication between Remote Fire Fighter & Fire Command Center. Each Telephone jack should have separate address. complete in all respects as approved and desired by the Engineer in-charge at site.
6
16512
2752
... More
Supply, installation, testing & Commissioning of Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center. complete in all respects as approved and desired by the Engineer in-charge at site.
1
10621
10621
... More
Supply, installation, testing & Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes/ Telephone Jack. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance complete in all respects as approved and desired by the Engineer in-charge at site.
13
57629
4433
... More
Supply, installation, testing & Commissioning of Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance. The solution should be from single OEM. OEM should have manufacturing facility in India. OEM Should have presence in India from last 15 year. OEM should have own toll free number for service & support of product. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 2 trained OEM certified engineers & distributor have its own registered office in Punjab complete in all respects as approved and desired by the Engineer in-charge at site.
1
4433
4433
... More
Supply, installation, testing & Commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.The solution should be from single OEM. OEM should have manufacturing facility in India. OEM Should have presence in India from last 15 year. OEM should have own toll free number for service & support of product. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 2 trained OEM certified engineers & distributor have its own registered office in Punjab complete in all respects as approved and desired by the Engineer in-charge at site.
6
22212
3702
... More
Supply, installation, testing & Commissioning of Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.The solution should be from single OEM. OEM should have manufacturing facility in India. OEM Should have presence in India from last 15 year. OEM should have own toll free number for service & support of product. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 2 trained OEM certified engineers & distributor have its own registered office in Punjab complete in all respects as approved and desired by the Engineer in-charge at site.
1
4611
4611
... More
Supply, installation, testing & Commissioning of Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed.The solution should be from single OEM. OEM should have manufacturing facility in India. OEM Should have presence in India from last 15 year. OEM should have own toll free number for service & support of product. Contactor shall off load the work to specialized agency having direct distributorship from OEM & distributor will have minimum 2 trained OEM certified engineers & distributor have its own registered office in Punjab complete in all respects as approved and desired by the Engineer in-charge at site.
7
36785
5255
... More
Supply,installation, testing & Commissioning of Digital Audio Amplifier with cabinet & Amp power supply. Amplifier shall be capable of N:N/N:1 configuration and shall be dual channel capable of processing Two of 8 audio channels and a total of 100 W at 70.7 VRMS output along with necessary enclosures with local FFT Raiser. The Digital Audio Amplifier shall be fully monitored for fault and alarm reporting. The proposed Digital Audio Amplifiers shall (be Wall/Panel Mounted) not be rail mounted / dependant on Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of Amplifier operation. The Amplifiers shall be distributed across the building/floor to manage the sound attenuation problem & for the best sound intelligibility. All amplifiers shall provide back up of minimum 5 hours using secondary power source(battery power/UPS power). .Executing agency should have project name specified OEM authorization on the time of supply and also have a minimum two OEM certified engineer for commissioning & programming complete in all respects as approved and desired by the Engineer in-charge at site.
1
168689
168689
... More
Supply,installation, testing & Commissioning of Integrated 8 channel Digital Voice Evacuation System Controller capable of broadcasting Evacuation Messages on the same peer-to-peer Network and 2 ways Communication capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. Products not having this feature must provide dedicated CPU for DVC. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. The panel shall be capable of self programming without any dependency on dongle or programming software. Quoted rate shall include supply of necessary software & hardware for programming the panel with all necessary licence. Panel shall have Modbus/ Bacnet over IP protocol for future integration with BMS. However, for the present arrangement the FA system will be standalone with 24x7 monitoring. The panel shall be capable of remote accessibility on a mobile app through cloud platform/solution. Designed to meet UL864, 10th Edition. .Executing agency should have project name specified OEM authorization on the time of supply and also have a minimum two OEM certified engineer for commissioning & programming complete in all respects as approved and desired by the Engineer in-charge at site.
1
264155
264155
... More
Supply, installation, testing & Commissioning of 2W Multi-Tap (0.25W; 0.5W; 1W; 2W), Ceiling/Wall Mount Speakers. The speakers shall be of the same make as that of the Control Panel & Amplifiers. They shall be compatible with supplied Amplifiers and shall work on 70.7Vrms. UL Listed. Project specific OEM authorization required for executing agency complete in all respects as approved and desired by the Engineer in-charge at site.
96
253056
2636
... More
Supply, installation, testing & Commissioning of Back box for speaker as per site requirement complete in all respects as approved and desired by the Engineer in-charge at site.
96
111072
1157
... More
Supply, installation, testing & Commissioning of fire resistance cable (Colour Red) (at 950° C for 180 minutes) of BS6387/BS7846 Fire Proof Cable, 2C X 1.5 sqmm, BS6387 & BS7846, annealed stranded copper conductor, mica fire resistant tape, XLPE insulated, low smoke & zero halogen (LSZH) bedding, galvanized steel wire armour, low smoke & zero halogen (LSZH) red outer sheath. 600/1000 volts. Fire resistant to IEC 331 & BS7846 F2/BS6387 & CWZ. Acid gas emission to BS EN 50267 (IEC60754), smoke emission to BS EN 50268 (IEC61034) and flame propagation to BS EN 50265, BS EN 50266 (IEC 60332-3) complete in all respects as approved and desired by the Engineer in-charge at site.
500
110000
220
... More
Supply, installation, testing & Commissioning of Online UPS 1 kva 800 Watts Tower UPS with 1 hour battery backup. Operating Temperature Range 0 to 40 Degree @ 100% Load @ 50 Degree with 50% Load,Storage Temperature -15°C~60°C, Relative Humidity 0-95% No condensates, Acoustic Noise 40 dBA @ 1 Meter, Cooling Forced air cooling by the internal fans, Input Socket IEC C13, Output Socket IEC C14, No of output sockets 3 No's, Rated Input Voltage 208/220/230/240 Vac, Maximum working input voltage range 160 to 300 Vac @ 100% Load, 100 to 300 Vac @ 50% Load, Input Power Factor 0.99, Input THDi% 5%, Generator Set Yes 1.5 x UPS Capacity, Rated kVA 1000 VA, Rated kW 800 Watts, Load type Resistive load/ lagging load/ non-linear load/ transformer load/ lighting load, Load power factor range 0.5~1 lagging, Load Crest Ratio 3:1, Online Efficiency 88%, Rated Battery Voltage 36 Vdc, Battery Type VRLA (Valve Regulated Lead Acid Battery), 12VDC, Battery backup Back UP : 936VAH, Maximum charging current 10 Amps, ECO Mode Available, Communication (Independent SCI) Available, Intelligent Card slot (Independent SCI) Available, OVCD Available, EPO Function Available, Intelligent Fans Speed control Available, Auto restart function Available, Cold start Available complete in all respects as approved and desired by the Engineer in-charge at site.
1
35962
35962
... More
PVC INSULATED PVC SHEATHED FR ROUND FLEXIBLE COPPER CONDUCTOR CABLE:
Supply and erection of PVC insulated PVC sheathed FR (2Core) round flexible wire with copper conductor cable (ISI marked) confirm to IS:694/1990 left bare in pipe or on surface with cleats of suitable size complete in all respect as desired by the Engineer-in-charge:-
-
-
-
... More
Overall size 1.5sq.mm (48/0.20mm), 2Core
600
28758
47.93
... More
HEAVY GUAGE WELDED CONDUIT PIPES:
Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:-
-
-
-
... More
Heavy gauge welded conduit pipe 25mm dia. (ISI marked 1.60mm thick) Flushed
450
63409
140.91
... More
PVC, HDPE PIPES & PVC FLEXIBLE PIPES:
Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:-
-
-
-
... More
Heavy gauge PVC conduit pipe 25mm dia. (ISI marked) Flushed
550
38940
70.8
... More
Providing Silent Diesel Generating Sets: 1No. 200KVA DG Set with AMF Panel
-
-
-
... More
Supply, Erection, Testing and Commissioning of Silent (Sound Proof) Diesel Generator Set 200 KVA /160KW with AMF Control Panel .It should be air cooled/water cooled naturally aspirated/ turbo charged/ turbo charged after cool (As per manufacturer standard).
ENGINE: The Diesel engine developing 250 BHP (Approx.) for giving a power rating as per ISO 8528- Part-1 ( With CPCB Norms-IV as amended upto date) in KVA at the load terminals of alternator at 1500 rpm at actual site conditions. The engine shall confirm to IS 10000/ ISO 3046/ BS: 649/ BS 5514 amended up to date have dynamically balanced Fly wheel, air cleaner (dry/ oil bath type) as per manufacturer standard. A mechanical/ electronic governor of TYPE A1 AND A2 to maintain engine speed at all conditions of load, daily fuel service tank of minimum 8 hours running capacity as per manufacturer standard, Dry exhaust manifold with suitable exhaust residential grade silencer to reduce the noise level.suitable self-starter for 12 V/ 24 V DC ,battery charging alternator unit and voltage regulator, Lubrication oil cooler,Lubrication oil filters with replaceable elements.
ENGINE CONTROL PANEL: Engine control panel fitted and having digital display i.e Start/stop key switch/push button, Battery charging indication,Engine Hours indications, Over speed indication, High water temperature indication, Lubricant oil pressure indication,) RPM indication and MCCB (Fixed Thermal and Adjustable Thermal protection) of suitable rating for outgoing supply. ALTERNATOR: The alternator should be designed as per (IS4722 and IEC:34 ) standard. Rated Power Factor : 0.8 (lag), Rated voltage : 230/415 volt, SPDP (Screen Protected Drip Proof), Degree of protection: IP-23, Ventilation : Self ventilated air cooled Alternator should have 40 degree maximum class H insulation, Automatic voltage regulator unit should be provided as per standard practice of manufacturer. Its voltage dip shall not exceed more than 20% of the rated voltage at any step load or transient load as per ISO 8528 (Part-1). Its efficiency at full load 0.8 power factor, 10% overload one hour in every 12 hrs of continuous use.
-
-
-
... More
ACOUSTIC ENCLOSURE: The enclosure shall be fabricated out the CRCA sheet of thickness not less than 1.6 mm on the outside cover with inside cover having not less than 0.6 mm thick perforated powder coated CRCA sheet. It should be IP54 Suitable for outdoor installation exposed to weather conditions, noise level up to 75 dB (A). All sheet metal parts should be processed through 7-tank pre treatment process and batteries accommodated in the battery rack .The acoustic lining should be made up of high quality insulation material i.e. Rockwool / glass/ mineral wool / PU foam of appropriate thickness & density for sound absorption.The inside of enclosure should be provided with at least one no. 28 W-T5 fluorescent tube light/ LED 10Watt luminaries controlled by a 5A switch for adequate lighting during servicing etc.with 2 year warranty from the date of installation. complete in all respect as desired by engineer at site:
AMF PANEL: AMF panel shall be fabricated out of 1.6 mm sheet steel, totally enclosed, dust, damp and vermin proof wall mounted/ free standing floor mounted type with IP-53 degree of protection & front operated, composite meter for digital display, HRC fuses of suitable rating. MCCB (Microprocessor based release) /ACB (Overcuurent/ overload, shorcircuit, instantenous, earth fault protection) should be used. Battery charger complete with voltage regulator, Voltmeter and Ammeter for charging the battery from external mains. This will be in addition to the battery charging alternator or dynamo fitted on the engine.All the components in the control panel shall be properly mounted, duly wired and labeled. Suitable terminals are to be provided for panel incoming and outgoing connections. System opeartion facility provided shall afford the following operational requirements. Necessary instruments and accessories such as voltmeter, power factor meter, KW meter, KWH meter, Ammeter, Frequency meter,battery charger.
MCCB 4 Pole 400A 35kA microprocessor based release: 2Nos.
Power Contactor 4 pole, AC-3 duty of suitable rating : 2 Nos. Digital Multifunction Meter to show, KW, KWH, KVAH, P.F. and frequency, CL-1, etc:1 No.
"R, Y, B' LED indicating lamps & "ON / OFF" LED indicating lamps
Over Voltage relay & Under Voltage relay
Battery charger (with trickle and boost charging): 1 Set.
8 window Alarm annunciator with separate hooter, accept, reset and rest push button:1No.
The model of engine will be decided by the Engineer in Charge. The Generator set should be installed at site on the suitable size existing plinth of RCC as per specifacation DG set as per satisfacation of the Engineer- in-Charge at site. The model of engine will be decided by the Engineer in Charge.
1
2760448
2760448
... More
INDOOR LT CABLES, CABLE TRAY & DWC PIPE:
-
-
-
... More
XLPE INSULATED UN-ARMOURED CABLES (LOOSE):-
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-
-
-
-
... More
Overall size 300sq.mm (3½ Core) Un-armoured (Loose) 1Run from DG Set 200KVA to AMF Panel
150
203259
1355.06
... More
PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:
Supply and erection of XLPE/ PVC insulated PVC sheathed (10 core) unarmoured copper conductor cable (ISI marked) confirm to IS:7098 (PART-I), 1988 loose in the existing trench or pipe with suitable size of copper thimbles/ lugs complete in all respect as desired by the Engineer-in-charge:- (From DG Set to AMF Panel)
-
-
-
... More
Overall size 2.5sq.mm (10 Core)
150
53001
353.34
... More
DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:
Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-
-
-
-
... More
Double walled corrugated (DWC) HDPE pipe 63/51 mm (outer/ inner dia.)
130
20269
155.92
... More
Double Walled Corrugated HDPE Pipe 90/76mm (Outer/ Inner dia.)
20
3982
199.11
... More
Double Walled Corrugated HDPE Pipe 160/ 136mm (Outer/ Inner dia.)
130
44372
341.33
... More
COPPER EARTHING
-
-
-
... More
COPPER EARTHING (Upto 14 metre in Length):-
iii- Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:- (Body earthing & Neutral Earthing)
-
-
-
... More
Earthing with 25mm x 3mm Copper Tape (upto 14Metre in Length) (Body earthing & Neutral Earthing: 4Nos. for DG Set 200KVA)
4
81284
20321.17
... More
Additional Length 25mm x 3mm thick Copper Tape
60
38229
637.16
... More
Providing 11 KV Compact Sub Station 500KVA For DAC Building:
-
-
-
... More
VACUUM CIRCUIT BREAKER:
-
-
-
... More
Supply, Erection, Testing and Commisioning of 11kV, 3Phase, 50Hz, Indoor metal clad, floor mounted, ‘Horizontal draw out’ type VCB (Vacuum Circuit Breaker) switch board unit 630 Amp. which includes 630/800 Amp. Vacuum Circuit Breaker for Incoming/ Out going feeder with Electrolytic Copper bus bars of suitable rating, Horizontal Isolation type as per IEC 62271-100-200. The Switchgear panels shall be sheet steel construction with ALUZINC not less than 2.5mm thickness for load bearing sections and not less than 2mm thickness for non-load bearing, dust, moisture and vermin proof to provide a degree of protection IP-4X in accordance with IS:13947. VCBs are type tested according to International Standards IEC-62271 at renowned laboratories. They are compact, safe and reliable. The Panels shall be tested for IAC level of 25kA/1 Sec. No. of operations of Vacuum interrupter bottles for better performance (i) At rated current: 10,000 operation (ii) No. of short circuit dead operation at rated short circuit current: 100 opeartion
-
-
-
... More
VCB parameters are as below: (a). Rated Voltage: 12kV
(b). Rated short circuit breaking current withstand : Min. 25kA for 3sec.
(c). Rated insulation voltage lightning (Impulse withstand) : At 75kV Peak
(d). Rated insulation voltage( Power frequency withstand) : Min. 28kV
(e). Rated operating sequence : O-0.3 sec - CO - 3 min-CO
(f). Spring charging mechanism : Manually as well as motor operated (230V, AC, 50Hz)
(g). Operation type: Manually and electrically open (Electrical-230V, AC,50Hz) (h). Earthing Switch : Mechanically interlocked device to prevent personnel from getting electric shock during breaker maintenance. VCB incorporating mechanical as well as electrical ON/OFF indiaction "OFF" push button, test/ serviceposition limit switches, with minimum 6NO+6NC breaker auxiliary contacts in service position, Manual charging of breaker should be done without opening the front door.
-
-
-
... More
Incomer shall consist of:
(a). Cast Resin CT's 11kV : 600-300/1-1A, Core1: Class1, 10VA for 3phase, Core2: 5P10, 10VA
(b). Cast Resin PT's 11kV : PT Ratio 11kV/√3 / 110V/√3 / 110V/√3, Class 1, Class 0.5 Burden 50VA
(c). Protections : Numerical instantaneous IDMTL mimic dispaly relay (230V, AC, 50Hz) : U/V, O/V, E/F, O/C, S/C & TCS with RS 485 Modbus protocol for communication & drawout type
(d). Master Trip/ Anti pumping relay
(e). Digital Voltmeter : Range 0-12kV with necessary voltmeter with built in selector switch & suitable for 230V AC 96x96 sq.mm dial with shrouded terminal.
(f). Digital Ammeter : Applicable Range with necessary ammeter with built in selector switch & suitable for 230V AC 96x96 sq.mm dial with shrouded terminal.
(g). Multi-function meter with suitable communication to Central Software dta control & SCADA system, Converter having facility of real time data monitoring, historical trend and web dashboard
(h). Necessary AC supply, healthy indication lamp & switch, TNC (Trip, Neutral & Close) breaker control switch with indicating arrangement, Local/ remote selector switch for breaker open/close operations
All the relays shall belong to a common platform and shall be of single make with Electro-mechanical type relays in draw-out casing. PCB shall be with conformal coating to withstand heavily polluted environments.
-
-
-
... More
Outgoing shall consist of:
(a). Cast Resin CT's 11kV : 600-300/1-1A, Core1: Class1, 10VA for 3phase, Core2: 5P10, 10VA (b). Protections : Numerical instantaneous IDMTL mimic dispaly relay : E/F, O/C, S/C & TCS with RS485 Modbus protocol for communication & drawout type for line feeder protection
(c). Master Trip/ Anti pumping relay
(d). Transformer Protection : 3 elements auxiliary relay (230V, AC, 50Hz) for transformer fault, Alarm for Buchholz, winding temperature & oil temperature (e). Digital Ammeter : Applicable Range with necessary ammeter with built in selector switch & suitable for 110V AC 96x96 sq.mm dial with shroded terminal
(f). Multi-function meter with suitable communication to Central Software dta control & SCADA system, Converter having facility of real time data monitoring, historical trend and web dashboard
(g). Necessary AC supply, healthy indication lamp & switch, TNC (Trip, Neutral & Close) breaker control switch with indicating arrangement, Local/ remote selector switch for breaker open/close operations
All the relays shall belong to a common platform and shall be of single make with Electro-mechanical type relays in draw-out casing. PCB shall be with conformal coating to withstand heavily polluted environments:-
-
-
-
... More
11kV, 3Phase, 50Hz, Indoor metal clad, floor mounted, ‘Horizontal draw out’ type VCB (Vacuum Circuit Breaker) Switch board unit 630 Amp. which includes 1 No. 630 /800Amp. Vacuum Circuit Breaker as Incomer, 2Nos. Vacuum Circuit Breaker as Out going feeder with in built power packs interconnected with Electrolytic Copper bus bars of suitable rating (2Nos. 800 KVA Transformer).
1
1600902
1600902
... More
COMPACT SUB STATION 500KVA: (1No. For DAC Building: )
-
-
-
... More
Supply, Erection, Testing and Commisioning of HT 11kV Package Substations is completely self-contained Solution for power distribution that includes Pre fabricated outdoor duty enclosure, high voltage switchgear, distribution transformer, low voltage panel and accessories such as power factor improvement equipment, control and protection equipments, all providing a cost effective. The complete unit shall be installed on a substation plint (base) as outdoor substation. Package substation shall have the following equipments: 11kV Switchgear: 11 kV, 3 Phase, SF6 compact switchgear panel with 11kV Load break switches controls incoming-outgoing feeder cables of 11kV ring main distribution system and Vacuum circuit breaker (VCB) as protection to the transformer.
The Load break switch, Vacuum circuit breaker, Bus bars should be mounted inside a sealed robotically welded stainless steel tank enclosure. The operating mechanism of switches and breakers shall be outside the SF6 tank and accesible from front. The tank should be filled with SF6 gas at an adequate pressure. The degree of protection for gas tank should be IP67.
-
-
-
... More
There shall be provision for filling the SF6 gas at site. Stainless steel gas tank shall confirm to the sealed pressure system and ensure the gas leakage to 0.1% per year as per IEC 60298. The Panels shall be tested for IAC level of min. 21kA/1 Sec. No. of operations of Vacuum interrupter bottles for better performance (i) At rated current: 10,000 operation (ii) No. of short circuit dead operation at rated short circuit current: 40 opeartion. Load break switch parameters are as below:
(a). 11kV, 3Phase HT manually operated Load break switches 630Amp., copper busbars with integral earth switch having ON/OFF/EARTHED indiaction, live cable indiaction cable termination bushing suitable for 300sq mm XLPE cable.
(b). Type: Load breaking and fault making in SF6 tank
(c). Fault making capacity : 52.5kAp
(d). Operating Mechanism: Operating handle with ON, OFF, Earth positions with arrangement for padlocking in each position
-
-
-
... More
VCB parameters are as below: (a). Rated Voltage/ PF withstand/ Impulse withstand: 11kV/28kV/52.5kVp
(b). Rated short circuit breaking current withstand : Min. 21kA for 3sec.
(c). Operating mechanism: Trip free & free handle type mechanically operated indication & pad locking
(d). Cast Resin CT's 11kV : 600-300/1-1A, Core1: Class1, 10VA for 3phase, Core2: 5P10, 10VA (e). Digital Ammeter : Applicable Range with necessary ammeter with built in selector switch & suitable for 110V AC 96x96 sq.mm dial with shrouded terminal.
(f). Protections : Numerical instantaneous IDMTL mimic dispaly relay : E/F, O/C, S/C & TCS with RS485 Modbus protocol for communication & drawout type (g). Master Trip/ Anti pumping relay
(h). Transformer Protection :3 elements auxiliary relay (230V, AC, 50Hz) for transformer fault, Alarm for Buchholz, winding temperature & oil temperature
-
-
-
... More
Transformer:
11KV/433V Distribution Transformer, Three Phase 50 Hz, Oil Immersed, Naturally Cooled ONAN, Core type Double wound with copper conductor conforming to IS:1180 (As amended upto date) Level-2 with all latest amendments, vector group Dyn11 suitable for packaged substation housed in a enclosure with corrugated tank arrangement hermeatically sealed. Transformer parameters are as follows:
(a). Off Circuit Tap changer: +5% to -10% off circuit tapping in steps of 2.5%. (b). Permissible Temp. Rise of Oil: 40°C
(c). Permissible Temp. Rise of Winding 45°C
(d). Magnetic Core: Prime grade of M4 or better (e). System Highest Voltage :- 12kV at the HV side (f). Terminations: Cable Box on HV & LV Side
(g). Insulation Level: ● H.V. Power Frequency (KV rms) : 28 kV ● H.V. Impulse withstand voltage (KV peak): 75 kVp
-
-
-
... More
Enclosure for PSS:
Outdoor type enclousre shall be made of 2mm thickness of galvanised sheet steel tropicalised to meet indian weather conditions including all the partition sheets and doors. The enclosure shall be corrugated type wall design for better heat dissipation, provinding robust construction and enclousre should have IP54 degree of protection for HT & LT switchgear compartment & IP 23 protection for transformer compartment. the base of the enclosure shall be of 4mm thickness hot dip galavanized sheet steel to ensure rigidity for easy transport & installation. The entire package substation shall be factory assemble & factory fitted. Each compartment should be provided with the door and pad locking arrangement. The unit shall be tested for internal arc fault test to the tune atlest 20kA for 1 second as per latest IEC 62271-202.
Interconnection & Earthing:
Interconnection between HT switchgear & transformer using screened covered aluminium XLPE single core cable & interconnection between transformer & LT switchgear using aluminium busbars with copper flexibles. Internal earthing connections by 50x 6mm G.I strips.
-
-
-
... More
LT switchgear: The LV compartment with Degree of protection-IP54 designed for a 50 degree C ambient temperature. The panel is modular, dead front, freestanding, floor mounted and comprises the following equipment
(a). LT switchgear with 433V suitable ampere rating Aluminium busbars with 100% neutral
(b). 1 No. MCCB/ ACB FP microprocessor based for O/C, S/C & Integrated E/F release type for incomer according to the KVA rating of the transformer
Metering compartment:
(a). 1 No.Digital multi functional meter class1.0
APFC Panel:
(a). Capacitor Banks shall be suitable for operation at 440V Three phases. The type of capacitor banks shall be self healing MPP type Heavy duty as per IS: 13340-1993 and shall be housed in sheet steel container to ensure the explosion free design. The external discharge resistors shall also be provided. Capacitor Banks shall be suitable for Overloading as 115% for Over Current and 110% for Over Voltage. The Watt Loss shall not be less than 0.5w/kVAr. The Relay shall be of 12 stages to improve the power factor at least 0.98. The relay shall be microprocessor based with self diagnostic and setting including C/K ratio.
-
-
-
... More
Package Substation 11kV HT Switchgear with 2 way RMU (RRL), consisting of 2 Nos. manually operated Load Break Switch 630 Amp., 1 No. manually operated VCB 630 Amp., 11KV/433V, 500kVA ONAN type transformer
LT PANEL: Air Circuit Breaker Four Pole, 800amp., 415volts (Electrical Draw-Out Type) of suitable ampere rating at 415V, 50Hz, 4 Pole Electrical draw-out type with inbuilt microprocessor based trip sytem with thermal memory, zone selective interlocking, pre trip alarm, individual fault indicating LED, O/C, S/C, Instantaneous & E/F internal protection, Impulse withstand voltage 12kV, rated insulation voltage 1000V, rated operational voltage 690V, fully rated neutral, protection against overload & shortcircuit with setting at 50%-100%-OFF, suitability for isolation as per IEC 60947-2. The ACB should be capable for recording 20 fault history, LCD Display of current & voltage, Icu = Ics = Icw (1 Sec.) = 50kA with no derating upto 50 degree celcius on the existing industrial panel (With terminal adapter on load and line side of breaker)
APFC PANEL: 1 No. MCCB TP Pole 400A Ics= 50kA Thermal magnetic with Double break mechanism. Intelligent APFC Relay with 160 kVAr MPP Heavy duty Capacitor with suitable rating of contactors & Short ckt. protection device for each banking.
1
3965197
3965197
... More
INDOOR MAIN LT PANELS : 1NO. FOR MAIN DAC BUILDING
-
-
-
... More
Designing, Supply, Erection, Testing & commissioning of indoor TTA LT Panel enclosure (dust, vermin and interchangeable modules with facilites for extensions or reduction as per the space or requirments). The Panel shall be suitable for operation at 415+6% Volts, 50HZ, 3 phase 4 wire & earth system. The assembly manufacture should be ISO approved and CPRI tested for short circuit of (minimum 50kA) as well as IP degree of protection (IP44).
Fabrication: Panel shall be made from 14/16 SWG CRCA sheet, conforming to IS:8623. The fabrication should be such that all the member i.e. vertical/horizontal should be detachable type i.e. total bolted. In case of any changes required at site should be possible then and their self without any cutting or welding. The fabrication of the panel in 3B construction fully compartmentalized type i.e. bus bar channel as well as the cable chamber should be totally isolated from the feeder chamber. Where the crossing of the wire or bus link should have proper rubber gourmets or non-hygroscopic material. No live part should be in visible condition. The base channel will be made out of 75mm x 40mm x 5mm rolled channel. "The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The panel door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. Minimum depth 400mm / wide 300 mm for busbar/ Cable ally at the front of the panel. The panel will be free standing floor mounting type having provision for cable entry from bottom/top with cable glands etc.
-
-
-
... More
Painting: The sheet metal is sprayed with corrosion resistant etch Primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work. Busbars: The panel shall be provided with TPN copper busbar of suitable size according to the size of MCCB's. All Busbar will be air insulated with codified in Red, Yellow, Blue & Black as per standard for cable termination with the help of extended busbar only with proper adjustable cable supports. The main busbar would be supported upon non-hygroscopic SMC/DMC supports.
Metering: The panel shall be completed with digital metering unit (with selector switches, voltmeter & ammeter) epoxy insulator, gasket, PVC sleeves, CT's & L.E.D. type indicator etc. Manufacturer of Panel should be CPRI Approved (Approval not older then 5 years) & ISO certified (Manufacturer workshop as per ISO 9001: 2015 standard). The Concerned contactor shall be approved the detailed drawing of panel with complete specification from the Engineer in charge at site.
Detail of capacities of ACB/MCCB's to be installed in the cubical panel Enclosure (including the cost of MCCB's+E.R.H.) as per following.
-
-
-
... More
Incomer:
■ Air circuit-breaker of suitable ampere rating at 415V, 50Hz, 4 Pole Electrical draw-out type with inbuilt microprocessor based trip sytem with thermal memory, zone selective interlocking, pre trip alarm, individual fault indicating LED, O/C, S/C, Instantaneous & E/F internal protection, Impulse withstand voltage 12kV, rated insulation voltage 1000V, rated operational voltage 690V, fully rated neutral, protection against overload & shortcircuit with setting at 50%-100%-OFF, suitability for isolation as per IEC 60947-2. The ACB should be capable for recording 10 fault history, LCD Display of current & voltage, Icu = Ics = Icw (1 Sec.) = 50kA with no derating upto 50 degree celcius on the existing industrial panel (With terminal adapter on load and line side of breaker), including bonding to the existing earth and making necessary connections with suitable size of thimbles as required by the Engineer-in-Charge at site and as per PWD General Specifications
Air Circuit Breaker Four Pole, 800amp., 415volts (Electrical Draw-Out Type) = 1No .
Outgoings-1: ■ On Load Change Over Switch Four Pole 400amp., 415volts = 1No.
■ MCCB 400A, 415V breaking capacity ≥36kA 4P microprocessor based adjustable thermal and magnetic protection = 1No.
Outgoings-2: ■ MCCB 630A, 415V breaking capacity ≥36kA 4P microprocessor based adjustable thermal and magnetic protection = 1Nos.
■ MCCB 400A, 415V breaking capacity ≥36kA 4P microprocessor based adjustable thermal and magnetic protection = 2Nos.
■ MCCB 250A, 415V breaking capacity ≥36kA 4P microprocessor based adjustable thermal and magnetic protection = 1Nos.
■ MCCB 63amp. 415 volts breaking capacity ≥25kA four pole fixed magnetic & adjustable thermalsetting MCCB unit = 3Nos. ■ MCB 63amp., 10KA, Four Pole unit = 3Nos. ■ All Incomers & Out going With Extendable Rotary Handle with adjustable depth complete as per schematic diagram attached & Satisfaction of the Engineer in charge at site.
Enclosure: Panel Size: As per Norms
1
893100
893100
... More
HT CABLE, END TERMINATION KITS & CONTROL CABLE FOR TRANSFOMER:
-
-
-
... More
XLPE INSULATED HT ARMOURED CABLES (UNDERGROUND):
Supply & laying of Circular Aluminium Conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FR PVC inner sheathed, galvanized steel strip armoured and overall FR PVC sheathed cable confirming to IS:7098 (Part-2), 2011 working voltage 11KV(E) grade to be laid 1.50 meter below ground level including excavation, sand cushioning, covering with sand & First class bricks and back filling the trench etc., of the required size:-
-
-
-
... More
HT Cable Overall size 35sq.mm (3Core) (From Metering Room to Substation Room 1+2 VCB & VCB to 500KVA Transformer)
100
86102
861.02
... More
XLPE INSULATED HT ARMOURED CABLES (LOOSE):
Supply & laying of Circular Aluminium Conductor screened with extruded semiconducting compound, XLPE insulated, insulation screened with extruded semiconducting combination in combination with copper tape (0.3KA for 1sec.) cores laid up, FR PVC inner sheathed, galvanized steel strip armoured and overall FR PVC sheathed cable confirming to IS:7098 (Part-2), 2011 working voltage 11KV(E) grade to be laid 1.50 meter below ground level including excavation, sand cushioning, covering with sand & First class bricks and back filling the trench etc., of the required size:- (From Metering Room to VCB & VCB to 2Nos. Transformers in Substation Room)
-
-
-
... More
HT Cable Overall size 35sq.mm (3Core)
20
10313
515.68
... More
S/E of Heat shrinkable cable end termination/ Straight through joint kit for 11 KVA /6.6 KV (E) XLPE Cables as approved & desired by Enginer in charge:-
-
-
-
... More
Heat Shrinkable End Termination for cable size 35 sq. mm, 3Core (Indoor Type)
6
16645
2774.29
... More
Heat Shrinkable End Termination for cable size 35 sq. mm, 3Core (Outdoor Type)
2
6545
3272.8
... More
PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:
Supply and erection of XLPE/ PVC insulated PVC sheathed (10 core) unarmoured copper conductor cable (ISI marked) confirm to IS:7098 (PART-I), 1988 loose in the existing trench or pipe with suitable size of copper thimbles/ lugs complete in all respect as desired by the Engineer-in-charge:- (From Substation VCB to Transformers 500KVA)
-
-
-
... More
Overall size 2.5sq.mm (10 Core)
100
35334
353.34
... More
INDOOR LT CABLES, CABLE TRAY & DWC PIPE:
-
-
-
... More
XLPE INSULATED UN-ARMOURED CABLES (LOOSE):-
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-
-
-
-
... More
Overall size 16sq.mm (4Core) Un-armoured (Loose)
200
26338
131.69
... More
Overall size 120sq.mm (3½ Core) Un-armoured (Loose)
200
117202
586.01
... More
Overall size 240sq.mm (3½ Core) Un-armoured (Loose)
150
167112
1114.08
... More
Overall size 300sq.mm (3½ Core) Un-armoured (Loose)
150
203259
1355.06
... More
Overall size 400sq.mm (3½ Core) Un-armoured (Loose)
100
168955
1689.55
... More
DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES:
Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-
-
-
-
... More
Double walled corrugated (DWC) HDPE pipe 63/51 mm (outer/ inner dia.)
200
31184
155.92
... More
Double Walled Corrugated HDPE Pipe 90/76mm (Outer/ Inner dia.)
180
35839
199.11
... More
Double walled corrugated (DWC) HDPE pipe120/103.50mm (outer/ inner dia.)
20
5815
290.77
... More
Double Walled Corrugated HDPE Pipe 160/ 136mm (Outer/ Inner dia.)
150
51199
341.33
... More
Double Walled Corrugated HDPE Pipe 180/152mm (Outer/ Inner dia.)
80
34133
426.67
... More
CABLE TRAY:
Supply and erection of MS perforated cable tray (MS Sheet thickness 2mm) with DA gray paint on the existing surface with the help of MS angle iron support (to be painted with approved paint) of size 50mm x 50mm x 6mm thick to be fixed with fastners/ nut & bolts etc., complete in all respect as desired by the Engineer-in-charge and as per PWD General Specifications:-
-
-
-
... More
Cable Tray Size 300mm x 50mm x 50mm (2mm thick)
20
29114
1455.73
... More
S/E of LT Cast Resin type/ Heat Shrinkable Termination Kit for Outdoor/ Indoor supply of 1.1 KV grade PVC/XLPE cable as desired by the Engineer in charge of the site:-
-
-
-
... More
Heat Shrinkable Outdoor/ Indoor End Termination Kit for Cable Size 3½/4 Core 400-630sq.mm
4
11986
2996.58
... More
Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-
-
-
-
... More
Brass Gland for Aluminium cable 2/3/4 Core size 16sq.mm
10
1302
130.21
... More
Brass Gland for Aluminium cable 2/3/3½/4 Core size 70sq.mm
4
763
190.89
... More
Brass Gland for Aluminium cable 3/3½/4 Core size 95-120sq.mm
8
2012
251.58
... More
Brass Gland for Aluminium cable 3/3½/4 Core size 240sq.mm
8
3600
450.06
... More
Brass Gland for Aluminium cable 3/3½/4 Core size 400sq.mm
10
6396
639.69
... More
Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-
-
-
-
... More
Aluminium thimble cable Core size 10 -16sq.mm
20
295
14.75
... More
Aluminium thimble cable Core size 25 -35sq.mm
10
179
17.91
... More
Aluminium thimble cable Core size 50sq.mm
10
284
28.44
... More
Aluminium thimble cable Core size 70sq.mm
10
316
31.61
... More
Aluminium thimble cable Core size 95sq.mm
10
368
36.87
... More
Aluminium thimble cable Core size 120sq.mm
10
453
45.3
... More
Aluminium thimble cable Core size 185sq.mm
10
653
65.32
... More
Aluminium thimble cable Core size 240sq.mm
20
2107
105.35
... More
Aluminium thimble cable Core size 400sq.mm
20
3308
165.4
... More
COPPER EARTHING
-
-
-
... More
COPPER EARTHING (Upto 14 metre in Length):-
iii- Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 10.50 metre (34.44 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 14metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 9metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-
-
-
-
... More
Earthing with 20mm x 3mm Copper Tape (upto 14Metre in Length)
4
74653
18663.38
... More
Earthing with 25mm x 3mm Copper Tape (upto 14Metre in Length)
2
40642
20321.17
... More
COPPER EARTHING (Upto 23 metre in Length):
Earthing with electrolytic Copper Tape rivetted (with 5Nos. copper rivets)/Steel Nut & bolts (with 4Nos. 32mm long, 8mm thick with washer and double nut) to 30cm x 120cm x 2mm thick copper plate (made cylindrical) burried 19.50 metre (63.96 feet) below ground level in the hole of excavation having bore dia. 125mm and surrounded by salt & charcoal dust mixture (20 kg.) including fixing the Copper Tape recessed in wall and in floor etc., up to 23metre in Length (including bore Length). G.I. pipe 20mm dia. (A-class), 18metre long should be laid in the hole of excavation 1 feet below ground level and having GI Reducer 50mm x 20mm with PVC Cap (For pouring water) fixed on the top level of the pipe. 300mm x 300mm x 300mm deep haudi of First class bricks finished with 1:4 cement plaster and haudi covered with cast iron lid having size 300mm x 300mm (Heavy) around the hole of excavation:-
-
-
-
... More
Earthing with 25mm x 5mm Copper Tape (upto 23Metre in Length)
8
303970
37996.37
... More
Additional Length 20mm x 3mm thick Copper Tape
80
41415
517.69
... More
Additional Length 25mm x 3mm thick Copper Tape
40
25486
637.16
... More
Additional Length 25mm x 5mm thick Copper Tape
160
166368
1039.8
... More
INDOOR LT PANELS:
-
-
-
... More
LT PANELS & MCCB's (MOULDED CASE CIRCUIT BREAKERS):
Designing, Supply, Erection, Testing & commissioning of indoor Type LT cubical panel enclosure (dust, vermin and interchangeable modules with facilites for extensions or reduction as per the space or requirments). The Panel shall be suitable for operation at 415+6% Volts, 50HZ, 3 phase 4 wire & earth system. The assembly manufacturer should be ISO approved and CPRI tested for short circuit of (minimum 50kA) as well as IP degree of protection (IP 54/55).
Fabrication: Panel shall be made from 14/16 SWG CRCA sheet, conforming to IS 8623/1977-82. The sheet metal used for the fabrication of control panel will be 2mm for load bearing member’s door and fittings plates etc. the partitions and other non load bearing members will be fabricated out of 1.6mm sheet, the sheet will be of mild steel CRCA type. The base channel will be made out of 75 x 40 x 5mm rolled channel. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The panel door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. Minimum depth 400mm / wide 300 mm for busbar/ Cable ally at the front of the panel. The panel will be free standing floor mounting type having provision for cable entry from bottom/top with cable glands etc. The fabrication should be such that all the member i.e. vertical/horizontal should be detachable type i.e. total bolted. In case of any changes required at site. it should be possible then and their self without any cutting or welding. The fabrication of the panel in 3B construction fully compartmentalized type i.e. bus bar chamber as well as the cable chamber should be totally isolated from the feeder chamber. Where there crossing of the wire or bus links. It should have proper rubber gourmets or non-hygroscopic material. No live part should be in visible condition.
Painting: The sheet metal is sprayed with corrosion resistant etch Primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work .
-
-
-
... More
Busbars: The panel shall be provided with TPN aluminium busbar of suitable size according to the size of MCCB's. Busbar shall be of high conductivity (53% to 58%) E91-E Grade aluminium (1A/Sq.mm). All Busbar will be air insulated with codified in Red, Yellow, Blue & Black as per standard for cable termination with the help of extended busbar only with proper adjustable cable supports. The main busbar would be supported upon non-hygroscopic SMC/DMC supports. Metering: The panel shall be completed with digital metering unit (with selector switches, voltmeter & ammeter) epoxy insulator, gasket, PVC sleeves, CT's & L.E.D. type indicator etc. Manufacturer of Panel should be CPRI Approved (Approval not older then 5 years) & ISO certified (Manufacturer workshop as per ISO 9001: 2015 standard) The Concerned contractor shall be approved the detailed drawing of panel with complete specification from the Engineer in charge at site.
Detail of capacities of MCCB's to be installed in the cubical panel Enclosure (Excluding the cost of MCCB's) as per following:-
-
-
-
... More
SUB LT PANEL (NORMAL):
-
-
-
... More
LT Panel enclosure having space for 1No. Incomer MCCB 630Amp. and 6Nos. outgoing MCCB's 40amp. to 250amp. (Option: MCCB 200-250amp.= 2Nos. and MCCB's 40-100amp.= 4Nos.) according to the requirement at site (Approx. size 1475 x 1800 x 400mm) (DETAIL SEE IN PANEL INVENTORY)
1
115898
115898.12
... More
SUB LT PANEL (EMERGENCY):
-
-
-
... More
LT Panel enclosure having space for 1No. Incomer MCCB 400Amp. and 8Nos. outgoing MCCB's 40amp. to 160amp. according to the requirement at site (Approx. size 1750 x 1750 x 400mm) (DETAIL SEE IN PANEL INVENTORY)
1
128637
128637.3
... More
SAFETY EQUIPMENTS:
-
-
-
... More
Providing and fixing H.T. danger notice plate of 250 mm x 200mm, made of mild steel at least 2mm thick and vitreous enamelled white on both sides and with inscription in single red colour on front side as required.
10
1390
139
... More
Providing and fixing M.V. danger notice plate of 200 mm x 150mm, made of mild steel at least 2mm thick and vitreous enamelled white on both sides and with inscription in single red colour on front side as required.
10
960
96
... More
Providing and fixing of Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878-1976 and cylinder fully charged of 4.5 Kg capacity.
10
69440
6944
... More
Supply and fixing of foam fire extinguishers, Portable ABC type 6Kg capacity hanged on wall with bracket component as required.
10
34620
3462
... More
Providing Advance Lightning Protection System:
-
-
-
... More
Supply, erection, testing & commisioning of Early Streamer Emission (ESE) type Lightning Protection Complete with Lightning Air Terminal. The System should be corrosion resistant stainless steel chrome body capable of working in hazardous atmosphere and protecting against direct Lightning point as well conducting /diverting it to earth completely after tracing the Lightning in advance. As per NF C 17-102:2011 the air terminal should be tested for Lightning impulse current (10/350 micro sec) =100 KA and for local certification the air terminal should be tested for switching impulse current of 40 KA (8/20 micro sec) as per CPRI with 5 positive and 5 negative impulse. The ESE Terminals shall offer a protection radius of 79mtr., Level-1 High Protection and preferably to be mounted on roof top and center of the building / blocks with the highly insulated polyplastic adaptor with the Mast. (Its working principle evolves from local electrostatic field that develops naturally around the system as a thunderstorm begins to gather. In the event of descending lightning, an inbuilt triggering device generates high tension pulses at the conductor tip, causing a ‘corona effect’.) Protection radius of 79Mtr at level 1 & 107 Mtr at level 4
1
85933
85933
... More
Supply and fixing of GI Mast 5 mtr. height along with suitable base plate for mounting the terminal along with highly insulated adopter to mount ESE Air Terminal with the Mast.The Adapter shall have suitable Metal connector /Connecting point in such a way the top portion shall be electrically connected to the central tip of the ESE terminal and bottom portion connected to the down conducto, stray wires along with support shall be securely fixed with base plate and gauge wires where ever required.
1
11572
11572
... More
Supply and installation of Lightning Strike Counter (6 digit display) of non-resettable (electromechanical) type which allows the automatic counting of the strikes received by the lightning protection system. This information is used to enhance lightning protection security & increase the effectiveness of inspection & maintenance procedures. It should be in IP-65 enclosure with minimum sensitivity of 1KA and maximum capacity 100KA. No external power source is required. It should be installed always 2 mtrs. above the ground level.
1
11479
11479
... More
Supply & erection of test Link of non-corroding, weather proof, water proof polycarbonate IP 65/55 enclosure including providing of 2 Nos. of insulated supports with suitable holes prefitted nuts & bolts to fix the down conductor & earth wire. The transparent cover fitted at approximately 500-1000mm from ground level shall be provided on each down conductor.
1
2687
2687
... More
Supply, installation & testing of chemical earthing (Maintenance Free Earthing) system with UL approved copper bonded rod and exothermically welded copper busbar both tested by CPRI at 50kA Fault Current. A copper bonded steel rod shall have 3000 mm length and 17.2 mm dia. with copper coating thickness of minimum 250 microns. Along with earth enhancement compound tested by ROHS complying IEC 62561-7 in a sealed bag of minimum 50 kg (25 kg Bag x 2). A copper clad steel solid ground wire of 8 mm dia. for interconnecting earth pits. Each earth pit shall be covered with heavy duty weather proof environment friendly polyplastic earth pit chamber. The grounding minerals should not be pollute the ground water. The grounding minerals shall be tested & certified for the resistivity of less than 0.12 ohm-mtr.
3
32262
10754
... More
Cost of pole foundation with earth work in excavation in foundations trenches etc. 0.25 meter below ground level, Cement Concrete 1:4:8 with stone ballast, Reinforced cement concrete M-20,Cold twisted deformed (Ribbed/tor Steel Bar) Bars Fe 500 grade as per IS 1786-2008 complete in all respect as desired by engineer in charge.
4
11609
2902.48
... More
PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:
Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-
-
-
-
... More
Overall size 70sq.mm (Un-sheathed) (Conductor connected the air terminal to earthing)
150
120178
801.19
... More
Providing Flood Lighting:
-
-
-
... More
PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:
Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-
-
-
-
... More
Overall size 1.5sq.mm (Un-sheathed)
100
2465
24.65
... More
XLPE INSULATED UN-ARMOURED CABLES (LOOSE):-
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications:-
-
-
-
... More
Overall size 16sq.mm (4Core) Un-armoured (Loose) (MAIN LT PANEL TO CUBICAL PEDESTAL)
100
13169
131.69
... More
XLPE INSULATED UN-ARMOURED CABLES (ON SURFACE):
Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed Un-armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid (On Surface) as per PWD General Specifications:- (For Flood Lights)
-
-
-
... More
Overall size 10sq.mm (3Core) Un-armoured (On-Surface)
300
32394
107.98
... More
DOUBLE WALLED CORRUGATED (DWC) HDPE PIPES: Supply and erection of Double Walled Corrugated (DWC) HDPE pipe to be laid 1mtr. below ground level including excavation placing the pipe in position and back filling with excavated soil etc. of the required size:-
-
-
-
... More
Double walled corrugated (DWC) HDPE pipe 63/51mm (outer/ inner dia.)
80
12473
155.92
... More
SHEET METAL CUBICAL PEDESTAL, TOWER STRUCTURES, HT & LT LINE ITEMS, MS CHANNELS, BRASS GLANDS, ALUMINIUM & COPPER THIMBLES:
-
-
-
... More
Supply and erection of M.S. Channel bracket made from 100mm x 50mm of length 600mm and height 600mm with M.S. angle iron 40mm x 40mm x 5mm for installing metal halide flood light fitting on it. Bracket should be fixed/ welded with the existing pipe of cover shed. The bracket should be painted with one coat of primer and two coats of approved paint. (For Flood Lights on Parapet wall)
12
16035
1336.26
... More
Supply and erection of SMC Junction Box (Glass Fibre reinforced polyester sheet moulding compound) confirm to IS:14772 (Recessed/ On surface), robustly constructed, safe & shock proof, rust & tamper proof of suitable inner & outer dimensions with ± 10% tolerance in size & hinged water tight cover with locking arrangement having 1No. terminal strip with 4Nos. terminals & 1No. Single pole MCB of required capacity fixed on din bar (Din Bar Provision for 2Nos. MCB's) complete in all respect as approved and desired by the Engineer In-Charge at site:-
-
-
-
... More
SMC Junction Box (Glass Fibre reinforced polyester sheet moulding compound) confirm to IS:14772, inner dimensions 200mm x 140mm x 95mm with hinged water tight cover with locking arrangement (For Flood Lights on Parapet wall).
12
10164
847.01
... More
GALVANIZED IRON PIPES AND G.I. EARTHING:
Earthing with G.I. wire/ rope in G.I. pipe partly recessed and partly on surface complete with 150cm long 50mm dia. G.I. earth pipe (Cutting threads and 36 Nos. holes, 1cm dia. to make a mesh around the GI Pipe) with G.I. reducing socket including erection of the same, 4.50 metre (14.76 feet) below ground level with 20Kg. charcoal & salt mixture etc., up to 8 metre in length (including boring & refilling).
(For Cubical Pedestal)
-
-
-
... More
Earthing with 8 S.W.G. (4mm dia.) G.I. wire in 15mm dia G.I. pipe with G.I. reducing socket 50mm x 15mm (upto 8Metre in length)
2
6631
3315.89
... More
Additional length G.I. wire 8 S.W.G. (4mm dia.) in 15mm dia. G.I. pipe (On Surface)
10
1843
184.36
... More
Supply and erection of heavy duty brass single compression gland for cable end termination duly complete with checknuts etc. including making necessary connections:-
-
-
-
... More
Brass Gland for Aluminium cable 2/3/4 Core size 10sq.mm
30
3147
104.93
... More
Supply and erection of heavy duty aluminium thimbles/lugs for cable end termination duly crimped including making necessary connections completely:-
-
-
-
... More
Aluminium thimble cable Core size 10 -16sq.mm
40
590
14.75
... More
SHEET METAL CUBICAL PEDESTAL, TOWER STRUCTURES, HT & LT LINE ITEMS, MS CHANNELS, BRASS GLANDS, ALUMINIUM & COPPER THIMBLES:
CUBICAL PEDESTAL: Supply and erection of Sheet metal cubical pedestal made from 50mmx50mmx6mm thick MS angle iron frame with 5 sides welded & covered with MS sheet 2mm thick & front side hinged with 4" hinges & locking system with single/ double door openable placed on MS strip of size 12.5mm x 2.5mm thick welded with MS sheet, 4Nos. legs of 50mmx50mmx6mm thick MS angle iron each of 600mm long with MS sheet 100mmx100mmx6mm thick at the bottom end of the legs. Front door welded x-sectionally with MS flat 25mmx5mm. The front side with MS sheet each 75mm wide & a bend of 75mm width outwards & inwards on all sides with tappered top 200mm high and pedestal with 4 Nos. supporting members each of MS flat 50mmx6mm thick according to cubical size duly welded & complete pedestal to be painted with 1 coat of red oxide & 2 coats of paint & bonding to the existing earth. The Pedestal platform should be filled with 1:2:4 cement concrete mixture and erected 150mm high from the top of the cement concrete platform. The job is to be completed as approved by Engineer-in-charge:-
-
-
-
... More
Cubical Size 900mm high, 600mm wide and 350mm deep with platform dimensions 700mm x 450mm x 450mm
1
12641
12641.37
... More
MCCB's (MOULDED CASE CIRCUIT BREAKER):
Supply and erection of Moulded Case Circuit Breaker (Panel mounting Cubicle type) in the existing Cubical Panel (conforms to IEC:60947-II) having Ics=100% Icu, 100% neutral with spreader links and relevant PWD General Specifications (Electrical Works) complete with G.I. Bolts, Nuts & Connection on both sides of MCCB with sutiable size of Thimbles etc.
-
-
-
... More
MCCB Four Pole 40amp., 415volts, ≥25kA Fixed Magnetic and Adjustable Thermal Setting
1
6626
6626.73
... More
MS SHEET ENCLOSURE FOR MCCB's:
Supply & Erection of indoor type MCCB enclosure of suitable size having provision for MCCB with extended rotary handle. The Enclosure shall be made from 14/16 SWG CRCA sheet, confirming to IS 8623/1977-82. The door should be double folded without edge and the gasket should be ‘S’ type puffed neutral rubber gasket for long life. The hinges of the door should be bolted type with double hole arrangement. The Enclosure door lock should be quick openable type spring loaded. There should not be any special tool or key to open the lock. The Enclosure will be wall mounting type having provision for cable entry from bottom/top with cable glands etc. The sheet metal is sprayed with corrosion resistant etch primer. The finishing treatment shall be applicable with air drying paint (7/9 tank Powder coated process should present in company pemises) after necessary putty work:-
-
-
-
... More
MS Sheet Enclosure having provision for MCCB 40-160Amp.with extended rotary handle (Approx. Size 500mm x 300mm x 200mm)
1
3342
3342.12
... More
TIMER:- Supply and erection of Switch S/E of Microprocessor Based Street Light Controller with digital time switch daily programmed with stand by lithium battery with back up of 6 years with min. time between 2 switching operations is 1 minute, three pole power contactors 40A. with coil voltage 220-230V AC with 1 no. aux. contact NO, MCB 2 pole 40amp. (C-Curve, 10kA) & power wiring with single core PVC insulated FR cable 10 sq. mm and control wiring with PVC insulated FR cable 1 sq. mm, 1 no. two position selector switch to bypass timer and other accessories & petty material (din rail, 4 pole bakelite terminal strip 63A/ 440V AC, required nut bolts) should be fixed on bakelite sheet 6mm thick to be mounted in a IP54 surface/ flush mounting powder coated sheet metal (1.60mm thick) cabinet having size 450mm x 600mm x 150mm to switch ‘ON’ all the 3 phases & switch ‘OFF’ 3 phases pre-fixed timings complete in all respect as per satisfaction of Engineer-in-charge:-
-
-
-
... More
Street Light Controller (For Three Single Phase Circuits) with 3 Nos. Three Pole Power Contactors 40A, 1 no. aux. contactor 6 amp. (2NO+2NC) with coil voltage 220V AC, 3 Nos. MCB 2 Pole 40amp. (C-Curve,10kA) & petty material (Din rail, 2 Nos. 4 pole bakelite terminal strip 63A/ 440V AC, required nut bolts)
1
15361
15361.08
... More
Supply and erection of LED Flood Light 120 watt, AC supply voltage 140-270 volts, 50Hz ± 3% (including BIS Certified potted single diver with screen or laser printing logo LED driver) with pressure die cast or extruded aluminium housing with control gear (IP 66 protection), THD10%, CRI minimum 70, High power LED (with wattage 1 to 5 watt) with mandatory secondary lenses, toughened glass fitting, 4 KV SPD within driver and 10KV external SPD, Min IK07, efficacy of LED fixture minimum 120 lumens per watt, 5 year warranty including their drivers complete in all respects as approved and desired by the Engineer in-charge at site. LED Fittings as per specifications approved by Hon'ble Technical Advisor to Punjab Govt. vide Letter ION No: AT/2021/GL/1410-1422 Dated: 06.05.2021. Besides this the lighting fixtures manufacturers should have in house NABL accredited lab.
12
122940
10245
... More
Supply and erection of LED Post top 40/35 Watt with IP 65 protection (including LED driver) having efficacy of LED fixture more than 100 lumens per watt and operating voltage between 140 to 270 volt, input AC frequency 50 Hz ± 3 % complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.The certification and Specifications of the LED Fitting's should be as approved by O/o Advisor (Techlical), Govt of Punjab vide Letter no.AT/2021/GL/1410-1422 Dated 06/05/2021
2
14038
7019
... More
Providing Solar Power Generation System:
-
-
-
... More
Grid interactive PV System Solar Power Plant of 95KWp:
-
-
-
... More
Supply, Installation, testing & Commissioing of Grid interactive PV System Solar Power Plant (i.e connected to utility grid) of Minimum capacity including required quantities of SPV modules (High power density Monocrytalline based single module of capacity +400 watt) formed into arrays, their mounting arrangement, Power conditioning units (i.e String Solar Inverter with 2Nos. GI Chemical earthing with suitable size GI strip upto string inverter and AC & DC distribution panel), required DC & AC distribution panels with surge protection units, cabling from terrace to main distribution board through Cable tray, Bi Directional Energy Meter, Provision of Lightening Arrestor & 2 Nos. GI chemical earthing with suitable size GI strip upto Lightning arrestor, Hot dip galvanized MS Mounting Structures (1No. GI Chemical earthing with suitable size GI strip upto mounting structure) should be designed to withstand the speed for the wind Zone of the location (150 Km/hr-170 Km/hr) Complete in all respect with transportaion, fabrication, labour & Civil Work etc. Features :- 1. Solar PV Module warranty 25 Years & certified under IS/IEC 61730 I & II IS/IEC 61701 & IS/EC 14286
2. Power Conditioning unit (string solar inverter) & certified under IEC/EN 62109-1, IEC/EN 62109-2, EN 61000-6-2, EN 61000-6-3, IEC 61683, EN 50530, IEC 60068-2-1, 2, 14, 30, EN 60529
3. Structure 25 Years service life with AMC & certified under IS 2062 2011
4. Complete Plant insurance for the period of 5 Years (Excluding Theft of the Material)
5. Annual Maintenance contract for the period of 5 Years
Conditions:
# The Plant will be installed as per MNRE and GOI guidelines and specifications. (Detail of material as per Annexure-I attached)
#The work will got done from approved MNRE (Misitry of New and Renewable Energy)/ PEDA (Punjab Energy Development Agency) contractor
#The capacity of solar power plant my increase or decrees as availability of site it can also be totally removed from executive end
The Rate are inclusive of all taxes including GST
95
5363985
56463
... More
Supply and erection of BLDC 5-Star rating AC Ceiling Fan 1200mm (48") regulator operated as per technical specifications: Sweep size: 1200mm, No. of Blades:3, Down Rod Length: 26cm, Motor type: BLDC, Star rating: 5-Star, Blade design: Ribbed blades, Blade finish: Powder coated, Rated speed: 350 revolutions per minute, Air delievery: 220 m/min., Power consumption: 26-28W, Rated frequency: 50Hz, Rated Voltage: 220-240 V, Net Contents: 1N Fan motor with PCB controller, 1N safety wire, 1N conopy set, 2N AAAbatteries (1.5V), 1N down rod, 1N instruction manual, 1N set of 3N fan blades, 1N shackle assembly & Guarantee: 2years etc., including erection & testing of ceiling fan having connection with PVC insulated PVC sheathed two single core copper conductor (FR) cable 0.75 sq. mm complete in all respects as per satisfcation of the Engineer in-charge at site.
166
609386
3671
... More
OCCUPANCY SENSORS:
-
-
-
... More
Supply and erection of Ceiling mounted Occupancy based PIR sensor (360 degree)with installation height 2.5mts ,8.5 Amps resistive load, Detection dia 8M,time delay - 5s to 59 mins , Light level threshold - 5 to 1275 Lux ,IP - 20,Sensitivity Adjustment, Walk LED test, with additional options like walkthrough, daylight set point, vacancy .
8
59104
7388
... More
SUSPENSION RODS FOR CEILING FANS:
-
-
-
... More
HEAVY GUAGE WELDED CONDUIT PIPES:
Supply & erection of Heavy guage welded conduit pipe (ISI marked) as per IS:9537:Part-II for wiring purposes including bends, junction boxes, Steel hooks, GI saddle clamps and other petty materials etc., where necessary including painting as per PWD General Specifications:-
-
-
-
... More
Supply & erection of 19/20mm dia. M.S. conduit pipe (1.6mm thick), white painted suspension rod for ceiling fan.
67
8823
131.69
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements