Public Works Department Tender

Table for Advocates Supplying & Placing Modular table in completely knock down conditions with an overall size 1500mm X 610mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor

3 Seater Bench for Public Supplying & Placing three seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm.

Steel Stool with cushion Supplying & Placing Stool made of CRC pipe of 25 mm round pipe Seat: approx. diameter 38.5 cm, Height of back rest: approximately 28.5 cm Total height: approx. 75 – 87 cm, height adjustment of the seat: approx. 47 – 59 cm Height is freely adjustable, can be rotated through 360 ° Well-padded seat, easy to clean

Chairs for Advocates Supplying and placing visitor chair with ergonomic design for user comfort. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The same shall be upholstered with tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used of black integral polyurethane arm with metal insert completely joint with seat and back. The frame structure shall be cantilever support type made up of MS/CRCA powder coated round pipe of Dia. 25.4mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. The seat size shall be 460±10 mm(W) X 450±10 mm(D) and back size shall be 460±10 mm(W) X 400±10 mm(H) from seat. Seat height = 450±10 mm, Overall height shall be = 830±10 mm, Overall width - 555±10 mm, overall depth = 595±10 mm

13. Steel Dustbin Supplying and placing Open Perforated Dustbin 7’’x10’’ Diameter X Height Having Capacity 6 Ltr Stainless Steel

Table 5'6" with Side Table Supplying & Placing executive table with credenza and pedestal unit in completely knock down conditions with an overall size 1650mm X 900 mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall have the size 1650 mm X 850mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form edges and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. Credenza unit shall be supplied for storage purpose with an overall size 900mm X 450mm X 750mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 nos. of shutter operated with the assistance of sliding rail track and SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal.. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Judges Sofa 3 Seater Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 530±10 mm(D) X 1520±10 mm(W), seat height = 430±10 mm, overall width = 1800±10 mm, overall depth = 720±10 mm & overall height = 790±10 mm.

Visitor Chair Supplying & Placing Visitor Chair ergonomically designed for user comfort & shall have asthetically appealing design. The seat shall be made of 15mm thick hot pressed malaysian plywood with HR polyurethane foam 50mm thick having density 40kg/m³ upholstered with leatherite in black colour with 0.8mm thick and 535 GSM and the back shall be made of double layered moulded hot pressed Malaysian plywood (12+6)mm thick with HR polyurethane foam 30mm thick having density 32kg/m³ upholstered with leatherite in black colour with 0.8mm thick and 535 GSM. The frame shall be cantilever support made up of MS CRCA chrome plated round pipe of Dia 25.4mm with 2mm thick. The armrest shall be covered with wooden arm. There shall be PPCP shoe provided at the base to avoid scratches on the floor . The Seat size shall be 475±10mm(W) X 490±10mm(D) and back size shall be 470±10mm(H) from seat & overall height = 930±10mm.

Center Table Supplying & placing center table with an overall size 1200mm X 600mm X 450mm. The top of the table shall be made up of 8 mm Glass thick on Pre-laminated particle board of grade II of IS 12823. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS powder coated pipe frame having cross-section area 30mm X 30mm. The table under structure shall consist of MS/CRCA chrome plated round pipe having Dia. 28mm. There shall be PPCP shoe provided at the base to avoid scratches on the floor

Table for Judgement writer Supplying and placing executive table with an overall size 1500mm X 850mm X 750mm. The top shall be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius.. Fixed top supporting pedestal shall be supplied at one side of the table. The pedestal shall be made up of 18mm thick Board . It should have 2 nos. of drawer i.e. 1 box and 1 filing. It should be operated on ball bearing sliding channel and recessed plastic handle with centralized locking mechanism. The table shall be clad with modesty panel. It should be 18mm thick made up of Pre-laminated particle board.There shall be leveller provided at the bottom. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Almirah for Steno Supplying and placing steel almirah in perfectly upright and straight position. The overall size of the Almirah shall be 915mm (W) X 485mm (D) X 1980mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf & door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50-60µ

3 Seater Bench for Public Supplying & Placing three seater bench. The seat and back shall be made up of high quality cold rolled MS perforated sheet of 1.2mm thick, pressed and welded to form the shape. The seat and back electrostatically coated with epoxy powder and then cured under heat to allow it to form a skin. The armrest shall be made up of mild steel powder coated tube with 1.2mm thick. The base structure shall be supported by MS powder coated with 40-60µ (DFT). There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 440±10 mm(D) X 405±10 mm(H) from ground. Overall height shall be = 775±10 mm, overall depth = 710±10 mm & overall width = 1765±10 mm.