Panjab University Tender

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(Ref DSR 13.80)

Demolishing brick work manually / by mechincal means including stacking of serviceable material and disposal of unserviceable material with in 50 metres lead as per direction of Engineer In -Charge

In Cement Mortar

Providing and fixing aluminium work for doors, windows , ventilators and partions with extruded built up standard tubular sections / appropriate z sections and other sections of approved make conforming to IS :733 and IS :1285, fixed with rawl plugs and screws or with fixing clips , or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with requried PVC/ neoprene felt etc. Aluminium snap b;eading for glazing / panelling C.P. brass / stainless steel screws , all complete as per architctural drawings and the direcstsions of Engineer-in -charge. (Glazing and panelling to be paid for separtely):(Ref DSR 21.1)

For fixed portion.(Ref DSR 21.1.1)

Powder coated aluminium (minimum thickness of powder coating 50 micron) 10 Gauge(Ref DSR 21.1.1.2)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).(Ref DSR 21.1.2)

Powder coated aluminium (minimum thickness of powder coating 50 micron) 10 guage.(Ref DSR 21.1.2.2)

Providing and laying Vitrified tiles of 600X600mm in size, with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in Flooring, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints.(Ref N.S.)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge.(Ref N.S.)

With float glass panes of 5mm thickness.

Providing and fixing 5mm thick bakelite sheet of approved brand by engineer-in-charge at site. The sheet is to be used in panelling work for aluminium door/winow/shutter and partition fixed in position with C.P. brass screw or EPDM gasket etc. Complete in all respect to the entire satisfaction of the engineer-in-charge.(Ref N.S.)

Providing & fixing powder coated aluminium handle of size 300mm long to be fixed with necessary screws and hardware. (Ref N.S.)

Providing and fixing Hydraulic door closer with logo printed along with necessary fittings. Complete in all respect to the entire satisfaction of the engineer in charge.(Ref N.S.)

Supply & FIxing of Modular Workstation back to back Overall size: 1150 mm L X 600mm D x 1200mm Ht.The workstations in the tile based modular partition system(fire retardant) of overall thickness 60mm. The frame shall comprise of vertical uprights and horizontal channel as knock down or welded structure. The vertical uprights and horizontal channel shall be made from 0.8mm thick CRCA sheet. The metal frame shall be power coated in Grey/Ivory/Black color after giving anticorrosion treatment. Level adjuster to be provided at the bottom of the verticals supports. Note: In back to back sitting arrangement vertical upright shall be common for two seats. Metal Raceway Two metal raceway shall be provided below the working top keeping an appropriate distance for electrical and internet wires respectively. Raceway shall be made of 1mm thick CRCA sheet or aluminum extrusion. Necessary cut out for switches, sockets and internet port shall be provided on raceway."

Frame Joinery: - The frame shall be joined to each other with the help of galvanized nut and bolts. Work Top: - Work top shall be made of 18 mm thick water proof and fire-retardant High Pressure Laminate/Compact Laminate. Working height of the work top shall be 750mm. Gable end: Gable end or support below the working top shall be made out of 40 x 40 x 1.2mm thick CRCA pipe. TILES 1. Metal Tiles: The matel tile shall consist of 1mm thick metal tiles made of CRCA sheet duly power coated. 2. Pin Up Board: 12mm thick particle board shall be provided on vertical panel i.e above work top for pin up board.(Ref N.S.)

Supply & Fixing of Modular Workstation without partition Overall size: 1150 mm L X 600mm D x 1200mm Ht The workstations shall tile based modular partition(Fire Retardant) system of overall thickness 60mm. The frame shall comprise of vertical uprights and horizontal channel as knock down or welded structure. The vertical uprights and horizontal channel shall be made from 0.8mm thick CRCA sheet. The metal frame shall be power coated in Grey/Ivory/Black color after giving anticorrosion treatment. Level adjuster to be provided at the bottom of the verticals supports. Note: In back to back sitting arrangement vertical upright shall be single. Metal Raceway. Two metal raceway shall be provided below the working top keeping appropriate distance for electrical and internet wires respectively. Raceway shall be made of 1mm thick CRCA sheet or aluminum extrusion. Necessary cut out for switches, sockets and internet port shall be provided on raceway. Frame Joinery: - The frame shall be joined to each other with the help of galvanized nut and bolts.

Work Top: - Work top shall be made of 18 mm thick water proof and fire-retardant High Pressure Laminate/Compact Laminate. Working height of the work top shall be 750mm. Gable end: Gable end or support below the working top shall be made out of 40 x 40 x 1.2mm thick CRCA pipe. TILES 1. Metal Tiles: It shall consist of 1mm thick metal tiles made of CRCA sheet duly power coated. 2. Pin Up Board: 12mm thick particle board shall be provided on vertical panel i.e above work top for pin up board.(Ref N.S.)

Supply & Fixing Office Table with Side Table Overall size: 1500mm L x 750mmD x 750mm Ht Top of the table shall be made out 18 mm thick water proof and fire-retardant High Pressure Laminate/Compact Laminate. Frame and leg of the table shall be made out of 50 x 25 x 1.2 mm thick CRCA pipe and modesty front panel shall be made out of 1 mm thick CRCA sheet and 600mm high. Sides of the tables shall be provided with MS CRCA sheet C- channel of size 670mm Ht x 110mm wide x 25mm depth to be made out of 1mm CRCA sheet and shall have design of square perforations. SIDE TABLE Overall size: 900mm L x 450mmD x 725mm Ht Top of side table shall be made out of 18 mm thick water proof and fire resistance High Pressure Laminate/Compact Laminate. Top frame of the side table shall be made out of c-channel of size 25x 60 x 25 mms to be made of 1.2mm thick CRCA sheet. Provided with storage cabinet having one drawer and below it a swing door. Storage cabinet shall be of size 645mm Ht x 300mm L x 450mmD. Drawer and swing door shall be lockable. Modesty panel or back shall be made of 1mm thick CRCA sheet. The welding wherever is required to be carried out with Resistance welding (Mig Welding). The complete body undergoes degreasing, derusting, phosphating & passivation before being powder coated and baked in oven at a temperature of 200oC. The Surface is to be finished with Fire Retardant Paint.(Ref N.S)

Supply & Fixing Modular Low Height Partition of tile based Fire Retardant modular partition system of overall thickness 60mm for office cabin. The frame shall comprise of vertical uprights and horizontal channel as knock down or welded structure. The vertical uprights and horizontal channel shall be made from 0.8mm thick CRCA sheet. The metal frame shall be power coated in Grey/Ivory/Black color after giving anticorrosion treatment. Level adjuster to be provided at the bottom of the partitions. Metal Raceway Two metal raceway shall be provided below the working top keeping an appropriate distance for electrical and internet wires respectively. Raceway shall be made of 1mm thick CRCA sheet or aluminum extrusion. Necessary cut out for switches, sockets and internet port shall be provided on raceway. Frame Joinery: - The frame shall be joined to each other with the help of galvanized nut and bolts.

TILES 1. Metal Tiles: It shall consist of 1mm thick metal tiles made of CRCA sheet duly power coated. 2. Pin Up Board: particle board shall be provided on vertical panel i.e above work top for pin up board/paper shall stick to the surface with the help of Pins. Cutting and bending of the CRCA sheet to be done in CNC machines to ensure the quality of end product. All the metal components of the workstations shall be made with Dies, Zigs and Fixtures so as to achieve precision and a complete interchangeability of components. The welding wherever is required to be carried out with Resistance welding (Mig Welding). The complete body undergoes degreasing, derusting, phosphating & passivation before being powder coated and baked in oven at a temperature of 200oC. The Surface is to be finished with fire retartdant paint.(Ref N.S.)

Supply & Fixing 3-DRAWER PEDESTAL UNIT IN CRCA SHEET CONSTRUCTION(with fire retardent paint) Overall Size: 400mm (L) x 520mm (D) x 690mm (Ht) The body and drawers of the pedestal unit is made of 0.8mm thick CRCA sheet and drawers’ front facia is made of 1 mm thick CRCA sheet. Provided with two small drawers and one big drawer. Two upper drawers’ size: 430mm L x 320mm B x 150mm Depth. Big drawer size: 430mm L x 320mm B x 265mm Depth All drawers move on telescopic channels. All drawers are provided with PVC insert handles. All drawers are lockable with single key. Provided with nylon level adjusters.Cutting and bending of the CRCA sheet to be done in CNC machines to ensure the quality of end product. The pedestal unit is to be made with Dies, Zigs and Fixtures so as to achieve precision and a complete interchangeability of components. The welding wherever is required to be carried out with Resistance welding (Mig Welding). The complete body undergoes degreasing, derusting, phosphating & passivation before being powder coated and baked in oven at a temperature of 200oC. The Surface is to be finished with Fire Retardant Paint.(Ref N.S.)

Supply & Fixing of Metal Key Board Trey(with fire retardent paint) shall be made out of 0.8mm thick CRCA sheet and moves on telescopic channels. The Surface is to be finished with Fire Retardant Paint.(Ref N.S.)

Supply & Fixing of Metal CPU Trolly (with fire retardent paint) shall be made out of 0.8mm thick CRCA sheet and to be provided with 4 nos 30 dia nylon casters, two are lockable. The Surface is to be finished with Fire Retardant Paint. (Ref N.S.)

Supply & Fixing of File Storage Cabinet Overall size: 1200mm Ht x 750mmL x 450mmD Body of the storage cabinet shall be made out of 0.8mm thick CRCA sheet and doors to be made of 1mm thick CRCA sheet. Provided with two adjustable shelves thus making three storage compartments. Doors shall be fixed with the help of steel hinges. Doors are lockable. The complete body undergoes degreasing, derusting, phosphating & passivation before being powder coated and baked in oven at a temperature of 200oC. The Surface is to be finished with Fire Retardant paint.(Ref N.S.)

Supply & Fixing Back Side Low Height Storage Cabinet.Top of the side cabinet shall be made of 18 mm thick water proof and fire-retardant .High Pressure Laminate/Compact Laminate. Edges of working top nicely polished or painted. Body of back side storage cabinet shall be made out of 0.8mm thick CRCA sheet and doors to be made of 1mm thick CRCA sheet. Provided with one fixed shelf thus making two storage compartments. Doors shall be fixed with the help of steel hinges. Doors are lockable. The surface is to be finished with fire retardant paint and bottom to be Provided with nylon level adjusters.

Overall size: 1500mm L x 450mmD x 750mmHt(Ref N.S.)

Workstation Revolving Chairs Seat width: 465mm Seat depth: 480mm Back Height : 440mm Back width: 450mm Chair seat(shall have 11mm thick ply) and back(shall have 11mm thick ply) shall be made of PU molded foam upholstered with high quality (fire retardant) fabric. Seat and back shall be provided with PP outer back cover. Chair shall have back tilt mechanism. Arms shall be solid made of PP materials. Height adjustment shall be achieved with hydraulic mechanism. Base of the chairs shall be made of sheet metal and duly chrome plated having 5 twin nylon casters for free movement. (Reff. N.S.)

Chair With High Back Seat width: 520mm Seat depth: 490mm Back Height : 600mm Back width: 520mm Chair seat and back shall be made of 11 mm thick ply cushioned with PU foam upholstered with high quality (fire retardant) fabric. Chair shall have back centre tilt mechanism. Provided with PU arms. Height adjustment shall be achieved with hydraulic mechanism. Base of the chairs shall be made of sheet metal and duly chrome plated having 5 twin nylon casters for free movement. (Reff. N.S.)

Visitor Chair Seat size: 410mm X410mmBack size: 410mmX260mmTo be built from 25mm dia 1.2mm thick CRCA Steel tube in cantilever shape. The pipe is bent into S shape; with heavy reinforcement at the bends to make it strong enough for bearing heavy cantilever load. The chair is so shaped that it gives very high seating comfort & stability. The seat and the back to be cut from 10.8mm thick hot pressed commercial ply and be provided with 40mm thick on the seat & 25mm thick on the back, 40 density polyurethane foam, upholstered with superior quality (fire retardant) fabric. Steel welding wherever required, shall be done by MIG welding process to minimize distortion and for the deep penetration of the weld. All the steel components are pre-treated for de-greasing, de-rusting and phosphating. After proper pre-treatment, the steel components shall be finished with fire retardant paint and oven baked at temp. Above 200 deg. C to provide scratch resistance surface coating film of thickness 40-45 microns. (Reff. N.S.)

Two -Bay Mechnanical Wheel Driven Compactor Consist – 24 Bodies i. Single Face 2-Bay Movable unit: - 915mm Length x 465mm Depth x 2400mm Height - 1 no ii. Double Face 2-Bay Movable unit: - 915mm Length x 900mm Depth x 2400mm Height- 5 nos iii. Single Face 2-Bay Fixed unit: - 915mm Length x 465mm Depth x 2400mm Height-1 no 2. BODY CONSTRUCATION (KNOCK-DOWN/BOLTED): Body shall be fabricated out of 0.8mm (min) thickness CRCA steel sheet i.e. thickness of top, side and back shall be 0.8mm (min). Face of the body (fixed or movable) shall be flushed with each other from top to bottom when brought together so as to make it dust proof. 3. SHELVES: SHELVES shall be fabricated/Press formed out of 0.8mm minimum thick CRCA steel sheet. It shall have minimum 6 folds to be designed for safe load bearing capacity of 80-100 kg (UDL). The front and rear sides of the shelves are stiffened with U channel so as to avoid the buckling of shelves or to bear impact load the shelves shall be fixed on the body by means of support brackets. Each compactor body shall have 4 No. adjustable shelves bolted with angle posts at equal intervals. The shelves shall be designed for load bearing capacity of 80-100 kg (UDL). The shelves shall be fixed over duty metallic adjusters fixed at all corners.

4. UNDER CARRIAGE:(A) SIZE OF UNDERCARRIAGE: Main channel of ‘C’ cross – section shall be size Minimum 65mm x 32mm x 3.15mm thick.(B) GUIDE RAILS: Cross section of the guide rail shall consist of ‘J’ channel made of 2.00mm (Min.) thick mild steel square bright bar of size 25mm x 25mm. Bright bar shall be fixed by screws to the channel.5. DRIVE MECHANISM: Mechanical hand wheel operation for moving the compartments (BLOCK): Movement of the body shall be through a drive Wheel and Sprocket-CHAIN Tensioner arrangement, which is mounted rigidly on the side of guide rail and body side. The drive arrangement shall be concealed by providing a CRCA sheet cover 1.00mm thick. Drive wheel shall be at the height of approximately 800mm the ground. Each under structure shall be fitted with four No’s antifriction bearings for guiding the under structure on the rail.6. LABEL HOLDER: Label holder shall be made of 1.00mm thick CRCA steel sheet of size 180mm x 110mm (Minimum).7. CENTRALIZED LOCKING: A centralized locking arrangement shall be provided on the back of the last unit so that it gets locked on the rail on bringing the entire unit together. In addition a spring loaded knob type safety lock shall be provided at the end of rail to prevent derailment.8. FASTNER: The nut bolt shall be galvanized /zinc plated.9. FINISH (to be finished with fire retardant paintt.) BODY: All CRCA sheets used in fabrication of the compactor bodies shall be finished with fire retardant paintt after carrying out surface treatment of all the sheets by using pre-treatment methods. The sheets shall be oven baked on temperature of 180 degree Celsius to 200 degree Celsius. UNDERSTRUCTURE: It shall be finished with fire retardant paintt in approved shade to minimum 45 microns after carrying out necessary pre treatment process. (Reff. N.S.) 9. FINISH (Powder coating) BODY: All CRCA sheets used in fabrication of the compactor bodies shall be finished with Epoxy Polyester powder coating of approved shade with fire retardant (45 microns minimum) after carrying out surface treatment of all the sheets by using pre-treatment methods. The sheets shall be oven baked on temperature of 180 degree Celsius to 200 degree Celsius. UNDERSTRUCTURE: It shall be power coated in approved shade to minimum 45 microns after carrying out necessary pre treatment process.

One -Bay Mechnanical Wheel Driven Compactor Consist – 12 Bodies SI i. Single Face 1-Bay Movable unit: - 915mm Length x 465mm Depth x 2400mm Height - 1 noii. Double Face 1-Bay Movable unit: - 915mm Length x 900mm Depth x 2400mm Height- 5 nos iii. Single Face 1-Bay Fixed unit: - 915mm Length x 465mm Depth x 2400mm Height-1 no2. BODY CONSTRUCATION (KNOCK-DOWN/BOLTED): Body shall be fabricated out of 0.8mm (min) thickness CRCA steel sheet i.e. thickness of top, side and back shall be 0.8mm (min). Face of the body (fixed or movable) shall be flushed with each other from top to bottom when brought together so as to make it dust proof.3. SHELVES: SHELVES shall be fabricated/Press formed out of 0.8mm minimum thick CRCA steel sheet. It shall have minimum 6 folds to be designed for safe load bearing capacity of 80-100 kg (UDL). The front and rear sides of the shelves are stiffened with U channel so as to avoid the buckling of shelves or to bear impact load the shelves shall be fixed on the body by means of support brackets. Each compactor body shall have 4 No. adjustable shelves bolted with angle posts at equal intervals. The shelves shall be designed for load bearing capacity of 80-100 kg (UDL). The shelves shall be fixed over duty metallic adjusters fixed at all corners.

4. UNDER CARRIAGE:(A) SIZE OF UNDERCARRIAGE: Main channel of ‘C’ cross – section shall be size Minimum 65mm x 32mm x 3.15mm thick.(B) GUIDE RAILS: Cross section of the guide rail shall consist of ‘J’ channel made of 2.00mm (Min.) thick mild steel square bright bar of size 25mm x 25mm. Bright bar shall be fixed by screws to the channel.5. DRIVE MECHANISM: Mechanical hand wheel operation for moving the compartments (BLOCK): Movement of the body shall be through a drive Wheel and Sprocket-CHAIN Tensioner arrangement, which is mounted rigidly on the side of guide rail and body side. The drive arrangement shall be concealed by providing a CRCA sheet cover 1.00mm thick. Drive wheel shall be at the height of approximately 800mm the ground. Each under structure shall be fitted with four No’s antifriction bearings for guiding the under structure on the rail.6. LABEL HOLDER: Label holder shall be made of 1.00mm thick CRCA steel sheet of size 180mm x 110mm (Minimum).7. CENTRALIZED LOCKING: A centralized locking arrangement shall be provided on the back of the last unit so that it gets locked on the rail on bringing the entire unit together. In addition a spring loaded knob type safety lock shall be provided at the end of rail to prevent derailment.8. FASTNER: The nut bolt shall be galvanized /zinc plated.9. FINISH (fire retardant paint) BODY: All CRCA sheets used in fabrication of the compactor bodies shall be finished with fire retardant paint of approved shade with fire retardant (45 microns minimum) after carrying out surface treatment of all the sheets by using pre-treatment methods. The sheets shall be oven baked on temperature of 180 degree Celsius to 200 degree Celsius. UNDERSTRUCTURE: It shall be fire retardant paint in approved shade to carry out necessary pre treatment process. (Reff. N.S.)

Electrical Works

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.(Ref DSR 1.3)

Group C(Ref DSR 1.3.3)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required.(Ref 1.17)

3 x 2.5 sq. mm(Ref 1.17.12)

3 x 4 sq. mm(Ref 1.17.21)

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.(Ref 1.18)

2 Pair(Ref 1.18.2)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.(Ref 1.21)

25 mm(Ref 1.21.2)

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.(Ref 1.24)

5/6 A switch(Ref 1.24.1)

3 pin 5/6 A socket outlet(Ref 1.24.4)

Telephone socket outlet(Ref 1.24.6)

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.(Ref 1.25)

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.(Ref 1.27)

1 or 2 Module (75 mmX75 mm)(Ref 1.27.1)

6 Module (200 mmX75 mm)(Ref 1.27.4)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.(Ref 1.32)

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.(Ref 1.33)

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.(Ref 1.53)

1 run of cable(1.53.1)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator)(Ref 2.4)

6 way (4 + 18), Double door(Ref 2.4.2)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.(Ref 2.10)

Single pole(Ref 2.10.1)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.(Ref 5.18)

Supply and erection of adopter box made of 16 SWG M.S. sheet duly painted of size 6” x 3”. complete in all respect to the entire satisfaction of the EIC.(Ref N.S.)

Supply and erection of angle iron frame out of an angle of size 25mmx25mmx4mm of suitable size as required at site with 16 gauge MS sheet duly painted with one coat of primer & Two coat of synthetic enamel paint. complete in all respect to the entire satisfaction of the engineer-in-charge.(Ref N.S.)

Supply and erection of 63 amp MCB TPN. complete in all respect to the entire satisfaction of the engineer in charge.(Ref N.S.)

Supply and erection of 4 pole 160 A MCCB of 25 KA 4 pole with enclosure complete in all respect to the entire satisfaction of Engineer-in-charge. (Ref N.S.)

Supply and erection of 4 pole 200 amp Busbar chamber, complete the job in all respect to the entire satisfaction of the Engineer-in-Charge.(Ref N.S.)

Supply and erection of 1'-0"x 4'-0"LED fitting of approved make. complete in all respect to the entire satisfaction of the Engineer in charge.(Ref N.S.)

Supply and erection of networking point RJ 45 (Internet Socket) with complete box required at site with bakelite sheet. complete in all respect to the entire satisfaction of engineer in-charge(Ref N.S.)

Supply and erection of 12 U rack on existing wall at any height including all lead and lift complete in all respect to the entire satisfaction of engineer in charge.(Ref N.S.)

Supply and erection of I/O (input/output) link including cost of box for the same in any height including lead and lift complete in all respect to the eintire satisfaction of the Engineer-in charge.(Ref N.S.)

Supply and erection of patch panel 24 port with required material in any height including lead and lift complete in all respect to the entire satisfaction of Engineer-in-charge.(Ref N.S.)

Erection for connecting of internet cable per nod on both sides including testing in any height including lead and lift complete in all respect to the entire satisfaction of the Engineer-in-charge.(Ref N.S.)

Supply and erection of patch cord with connector on both ends in any height including lead and lift complete in all respect to the entire satisfaction of the Engineer-in-charge.(Ref N.S.)

S/E/T/C of managable network switch 24 port 1x100 mbps speed or above. complete in all respect to the entire satisfaction of the Engineer-in-charge.(Ref N.S.)

Supply & Fixing Penta scanning of internet points with the help of penta scanning machine including labour charges to operate it complete in all respect to the entire satisfaction of the Engineer-in-charge.(Ref N.S.)

Supply and erection of PVC insulated PVC sheathed aluminium conductor un-armoured (3.5 core) cable of size 50 Sqmm on surface complete the job in all respect to the entire satisfaction of the Engineer-in-charge. (Ref N.S.)

Supply and erection of Telephone tag box 24 pair complete in all respect to the entire satisfaction of the Engineer-in-charge.(Ref N.S.)