National Agri Food Biotechnology Institute Tender

Providing and laying in position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : All works upto plinth level and above at all levels. 1:2:4 (1 cement(ultratech/ACC/Ambuja) : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Structural steel work riveted, bolted or welded in built up sections,trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coat of synthetic enamel paint all complete.

Providing and fixing precoated green color galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Paid only total length of section fixed not individual sheet.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coat of paint synthetic enamel silver color, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer & two coat of synthetic paint complete.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Dismantle of Existing MS frame Puff panel structure and stacked the dismantle puff panel and ms structure to be stacked near Utility 01.The debris of dismantled area to be stacked as per direction of engineer in charge near low lying area. No extra payment will be made rather then quoted amount for diamntle and clean the area.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Dismantled Steel work of existing seed store to be used in new storage shed construction including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer and two coat of paint synthetic enamel, including welding and bolted with special shaped washers etc. complete.

Providing and Fixing 24" FRP withh height 18" base SS body Aluminum Blade Wind turbine ventilator as per direction of engineer - in charge