Food Corporation Of India Tender

Sub Head -II ( Cabling and Laying ) Supply of PVC insulated and PVC sheathed XPLE power cable of 1.1 KV grade armoured UG aluminium conductor cable conforming to IS 7098 part 1 with up-to-date amendment of the following size as required. 3.5*95 sqmm

4*10 sqmm

3*10 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Upto 35 sq. Mm (DSR 2022 item no. 7.5.1)

Above 35 sq. mm and upto 95 sq. mm (DSR 2022 item no. 7.5.2)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle) (DSR 2022 -Item no.7.7.1)

Above 35 sq. mm and upto 95 sq. mm(clamped with 25x3mm MS flat clamp) (DSR 2022 item no. 7.7.2)

Supplying and fixing of light class G.I. pipe of 50 mm dia.(nominal) 3 metres length along the pole for protection of under ground cable as required. (DSR 2022 item no. 12.37)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. .direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal) (DSR 2022 item no. 14.16.1)

90 mm dia (OD-90 mm & ID-76 mm nominal) (DSR 2022 item no. 14.16.2)

Providing, laying and fixing following following mm dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required 100mm dia (DSR 2022 item no. 14.13.3)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 X 10 sq. mm (22mm)(DSR 2022 item no. 9.1.7)

4 X 10 sq. mm (25mm)(DSR 2022 item no. 9.1.32)

3½ X 95 sq. mm (45mm) (DSR 2022 item no. 9.1.24)

Sub Head -III ( Fittings) Supplying, installation, Testing and commissioning of 45 watt LED streetlight made up of pressure die cast housing with toughned glass/PC embedded lens and individual high power LEDs , IP65 or IP66 protection with impact resisitance of IK07/IK08 and fixing on truss /wall/ pole with suitable clamps and nut bolts including giving connection testing etc., at site of work as required.

Supplying, Installation, Testing & Commissioning of Integral 50W LED flood light with driver inside a PDC housing with IP66 protection and suitable fixing accessories accessories on wall/ GI Pipe/tower/truss of the godown , making connections from the existing point / loop in loop out box to fittings with copper conductor round flexible cable etc. as required.

Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required (DSR 2022 item no. 12.34)

Supplying and fixing street light loop in loop out boxes with PVC Box of size 8"x6"x4" with 1 No. 6A SP MCB, 2/4 way strip connector i/c testing as reqd. (Confirming to releveant Indian Standards amended upto date)

Supplying, Installation and fixing on site of hot dip galvanized octagonal pole of length 7metres (sheet thickness 3mm), top dia. 70mm and bottom dia 130mm. Pole should be supplied in one piece. The Pole Should be equipped with 1. Inspection door , it should have a triangle key that forces the door out when opening . 2. Bakelite terminal strip win din bar for MCB and stud terminals (for mounting inside base compartment of the pole). 3. Base plate welded to the lower part of the Pole from outside and inside to serve for fixing the Pole to R.C.C. foundation by means of four bolts, thickness of the plate shall not be less than 16 mm, and its dimensions shall not be less than 240mmx240 mm. 4. 4 nos of anchor bolts with j-shaped made of atleast M20 grade, each bolt provided with washers and 2 nuts and each bolt should be of minimum length of 700mm. 5.Pole should be fitted with Pipe cap type single arm pole bracket made with suitable cap pipe and 48.3 mm dia, 3.25 mm thick pipe arms and bracket length of 1000 mm. with suitable angle of tilt. the arm shall hold in its position by 4 nos of screws or as required. 6. C curve SPMCB of 6 Amp and 2/4 way strip connector shall be fitted inside the pole compartment . 7. An earthing connection point shall be provided inside the pole near the door opening Foundation: RCC foundation of size 550mmx550mmx1500mm of M20 Grade(1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)) with excavation by Manual or Mechanical means upto depth of 1300 mm and Steel Reinforcement with Cold Twisted Bars (Confirming to releveant Indian Standards amended upto date) should be made for installation of the pole and to ensure that the pole can withstand wind speed as per IS 875 Part III 2015 amended upto date without bending,breaking and failure. All the materials, Galvanization and coating should follow latest Indian or applicable standards amended upto date.

Supplying and fixing of 2m length of GI pipe of 15mm(Medium Class) on the poles to give protective covering to the electrical connection to the street light

Sub Head -IV( SwitchGear and Earthing) Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door(DSR 2022 item no. 2.4.1)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole (DSR 2022 item no. 2.10.1)

Triple pole and neutral (32 A) (DSR 2022 item no. 2.10.5)

Sub Head -V ( Bus Bar, ChangeOver and Controller) Supplying, installing on ground with suitable mounting arrangement through MS Stand of length atleast 500 mm made of angle iron of size 50*50*6mm, testing and commissioning of Weather Proof, Dust Proof, Water Proof , 1.6mm thick CRCA steel enclosure of minimum size 700*400*200 mm duly painted with powder coating with appropriate number of incoming and outgoing cable gland tray,proper locking arrangement and 4 nos of 250A Aluminium Bus bars and 250 A 4P Changeover Switch with Extended Handle along with interconnections, earthing etc. as required.Suitable Provision shall be provided in the Enclosure to operate the handle of Changeover from outside (Confirming to releveant Indian Standards amended upto date)

Supplying, Installation, testing and commissioning of Single phase submersible pump starte motor/Controller suitable for rating of 1.5 HP Excellent aesthetics Flush mounted push buttons Enclosures with atleast IP54 degree of protection Lockable push button Terminal block for ease of termination Copper and aluminium terminations possible

Sub Head -VI ( Frames and Enclosure) Supply and fixing of 300mmX300mm size metallic frame cover fabricated with 25mm X 25mm X 3mm angle iron welded construction frame structured and 3.0mm thick M.S sheet cover plate with double hinges and locking arrangement including painting and fixing in wall including chasing and plastering complete and finishing as reqd.

Supply and fixing of 250mmX300mm size metallic frame cover fabricated with 25mm X 25mm X 3mm angle iron welded construction frame structured and 3.0mm thick M.S sheet cover plate with double hinges and locking arrangement including painting and fixing in wall including chasing and plastering complete and finishing as reqd.

Supply and fixing of 250mmX250mm size metallic frame cover fabricated with 25mm X 25mm X 3mm angle iron welded construction frame structured and 3.0mm thick M.S sheet cover plate with double hinges and locking arrangement including painting and fixing in wall including chasing and plastering complete and finishing as reqd.

Supply and fixing of 200mmX250mm size metallic frame cover fabricated with 25mm X 25mm X 3mm angle iron welded construction frame structured and 3.0mm thick M.S sheet cover plate with double hinges and locking arrangement including painting and fixing in wall including chasing and plastering complete and finishing as reqd.

Supply and fixing of 800mmX1000mm size metallic frame cover fabricated with 35mm X 35mm X 5mm angle iron welded construction frame structured and 3.0mm thick M.S sheet cover plate with double hinges and locking arrangement including painting and fixing in wall including chasing and plastering complete and finishing as reqd.