Bhakra Beas Management Board Tender

Carriage of Earth,Surkhi, Sand, Earth, Fly Ash, Bajri, Ballast, Stone Boulders, Kankar and Building Rubbish, Earth 1.0 km Including loading and unloding. [CSR item No.-5.2(i) & 4.1 (A)]& A&C-3

Cement concrete 1:8:16 With stone aggregates 40mm gauge mixing by mechanical means using concrete mixer volumetric type (CSR10.6 (b) (ii) )

Cement concrete 1:6:12 with stone ballast 40mm gauge stone aggregate. mixing by mechanical means using concrete mixer volumetric type [CSR item No. 10.8 (b) (ii) ]

Cement concrete 1:2:4 With stone ballast or shingle mixing by mechanical means using concrete mixer volumetric type ( CSR10.13 (a) (ii))& A&C-1

40 mm thick cement plaster D.P.C. 1:3 with admixture of water proofing compound @ 1 Kg/ Bag of cement (CSR15.51)

First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth (CSR item No. 11.7)

First class burnt brick work laid in cement sand mortar 1:4 in first storey up to 4 metres above plinth level. [CSR item No. 11.8]

12.5 mm thick cement plaster 1:5 [CSR item No. 15.10]

Centering and shuttering for faces of walls, partitions, retaining walls and the like (vertical or battering including,attached pilasters buttresses etc. [CSR item No. 9.2]

1.2 Meter high G.I. barbed wire fancing with 1.2 meter angle iron post 40X40X6mm placed every 3 meter center 0.3 meter below wall level every 15th post end post, corner post suitably strutted provided with 5 horizontal lines and two diagonals interwoven with wires fixed with GL staples , turn buckles etc. Including foundation concrete 1:2:4 of size 0.23X0.23X0.30m for each post complete as per technical clause 807 of MORTH specification (AOR Attached)

Providing and laying 60 mm thick factory made cement concrete interlocking Paving blocks of M- 35 grade manufactured by block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63 -2014 and of approved size and design / shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in- Charge.& Extra Cost for using darker fast shade for interlocking pavers Tiles of any shape & thickness instead of grey colours(CSR item No.14.138 &14.141 )

Finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm Unit(CSR item No.16.59)& A&C-1

Iron grated doors, including pintle hinges & arrangements ( CSR 18.5) 4No 10' x 5 ' 7 No 14' x 5' = 4x150 Kg , 7 x 200 Kg Each = 2000Kg

Applying priming coat with metal primer on new steel or iron work including preparation of surface ( CSR 16.20)

Painting two or more coats excluding priming coat with ready mixed paint for metallic surfaces in all shades on steel or iron work ( CSR 16.21 )

Providing and fixing ( PPGL) precoated painted galvalume sheet roofing (size, shape and pitch of corrugation as approved by Engineer-in-charge) The end rib shall have anti cappillary groove and return leg. The steel sheet must be having yield strength of 550 MPa ( Fy= 550 MPa) metallic coated with Zinc- Aluminium alloy ( i.e. 55% Al, 43.4%Zinc, 1.6% Si-Zincalume) AZ150 ( Min. 150 bm/mm2 total on both sides), pre painted with super Durable Polyster XRW quality paint includes inorganic infrared reflective pigment. The sheet confirms to general requirement of AS/NZS 2728 type 4/ IS 15965 class 3 durability and gloss value of 25% -40%. should be supplied in single length upto 12 metre or as desired by Engineer-in charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.50 mm (+ 0.05 %) thick [ CSR Item no.13.27 iii (a) ] & A&C-4

Coloured Granite stone tiles 15mm to 20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramp[ CSR Item no.14.88]

Wrought iron & Mild steel ladders, framed grills, gratings etc. with ends of bars riveted or molded forged framed window guards, barred iron doors stair case iron railing etc. including cost of bolts and nuts, screws, welding rod complete fixing in position. [ CSR-item No.18.4]

Supplying and fixing rolling shutters, of approved make, made of 80mmx1.25mm, M.S. Laths, interlocked together through their entire length and jointed together, at the end, by end locks, mounted on specially designed pipe shaft, with brackets, side guides, 27.5cm long wire spring grade No. 2 and arrangement for inside and outside locking with push and pull operation complete, including top cover 0.80mm thick (payment is to be made for the exact size of opening where rolling shutter is to be fixed) ( CSR 18.11 A )

Supply & erection of PVC Conduit Pipes (ISI marked) as per IS9537:Part-III & HDPE pipes (ISI marked) as per IS:4984:1995 for wiring purposes including bends, junction boxes, Steel hooks, M.S. saddle clamps and other petty materials etc., as per PWD General Specifications:- Heavy Gauge PVC Conduit Pipe 25mm dia. (On Surface) ( CSR 34.12 ii )

Supply and erection of PVC insulated FR single core Unsheathed copper conductor cable (ISI marked) suitable upto 1100 volts grade confirm to IS:694/1990 left bare in pipe or casing of suitable size complete in all respect as desired by the Engineer-in-charge:-Overall size 1.5sq.mm (Un-sheathed ( CSR 34.09 II )

Wiring in PVC insulated copper conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in heavy gauge PVC conduit pipe 20mm/ 25mm dia (ISI Marked) installed on surface etc., complete with PVC boxes (Plastic on surface boxes) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), MS saddle clamp, PVC Circular junction Boxes (Four way 1½" deep for walls), bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc., including the cost of above material and painting as required:-Wiring light point ( CSR 34.07 A II )

Supplying and fixing outdoor gate light of approved make , fixing of all accessories etc, all complete as per directions of Engineer-in- Charge A. Gates Column

Supplying and fixing outdoor gate light of approved make , fixing of all accessories etc, all complete as per directions of Engineer-in- Charge B. Wall Lamps