Airports Authority Of India Tender

Supplying and Placing in position Office Table of Size 1500W X 750D X 728H. Table without CPU Hanger size shall be 1500 Width mm x 750 depth mm x 728 Height mm. Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edge banding. Under structure Modesty Panel 18 mm thick Pre laminated particle board. The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA, Finish: powder Coat (epoxy polyester). Leg shall be fabricated component in 38 mm x 25 mm x 1.2 mm thick MS ERWA Tube, finish powder coat (epoxy polyester). The plastic cap for cable travel shall be injection moulded polypropylene and leveller glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyester) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyester) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyester) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyester). Epoxy polyester coating thickness of 50 microns (+/- 10) should be provided.

Supplying and Placing in position High Back Revolving Chair. The seat assembly should be made up of 1.2 ±0.1cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. Seat size: 47.0 cm. (W) x 48.0 cm. (D). The back assembly should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. Back size: 46.5 cm (W) x 70.5 cm (H). HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. The mechanism should be designed with the following features-360° revolving type,17° ±2° maximum tilt on pivot at centre, Upright position locking, Tilt tension adjustment. pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal should be injection moulded in black 33% glass-filled Nylon 6 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)The twin wheel castors should be injection moulded in black nylon. Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm.Height - min 99.5 to max 110.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Supplying and Placing in position Mid Back Revolving Chair. The seat assembly should be made up of 1.2 ±0.1cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. Seat size: 47.0 cm. (W) x 48.0 cm. (D). The back assembly should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm thick MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. Back Size : 46.5 cm (W) x 60.5 cm (H). HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. The mechanism should be designed with the following features-360° revolving type,17° ±2° maximum tilt on pivot at centre, Upright position locking, Tilt tension adjustment. Pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm.The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors.)The twin wheel castors should be injection moulded in black nylon. Overall Dimensions of Chair Seat Height - min 43.3 to max 54.3cm.Height - min 89.5 to max 100.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Supplying and Placing in position Visitor Chair. The seat assembly should be made up of 1.2 ±0.1cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded Polyurethane foam. The back assembly should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn back size should be: 46.5 cm. (w) x 60.5cm. (h)The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair, Seat Height - 46.5cm, Height - 93.5cm.Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm.

Supplying and Placing in position Office Table with Back Unit (Comprises of Main Desk , ERU and Pedestal). The Main table shall be of size 3600 Width mm x 1080 mm Depth x 750 mm height. Top surface of the table shall be made up of MDF board duly finished with Veneer and final coating of PU. The Main desk should contain in Smart Case - space slides effortlessly in style. The mobile Pedestal shall be of size 480 Width mm x 640 Depth mm x 600 Height mm. Mobile pedestal shall be coated of MDF with veneer coating and PU coating. The ERU Top shall be of MDF duly finished with veneer and final PU coating. Size of ERU top 1900 Width mm x 480 Depth mm x 550. The main desk is provided with the wire management system also there should be storage side unit. The Size of the Back unit shall be 3000 mm width x 480 mm Depth x 2035 mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. The mobile unit should be available in multiples coating hardness 1.5H.

Supplying and Placing in position High Back Revolving Chair: The seat should be made up of 1.2 ± 0.1cm thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. The back foam should be designed with contoured lumber support for extra comfort. Back size: 53.0cm.(w) x 95.4cm.(h) seat size:54.6cm.(w) x 49.0cm.(d). The HR polyurethane foam should be moulded with density = 45 +/-2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression. The seat and back should be arrested together with spine made of 0.8 ±0.05 cm thick HR steel and should be black powder-coated ( dft 40-60 microns ). The armrest assembly: the armrest assembly should comprise of three parts viz. The armrest support tube and p.u. armrest and the armrest top. The armrest tube assembly should be made of 2.54±0.03cm x 0.16±0.0128cm M.S. E.R.W. support tubes and chrome plated. The P.U. armrest should be made of black integral skin polyurethane with 50-70 shore 'A' Hardness and reinforced with M.S. insert. The armrest top should be made of ABS & upholstered with foam & leather. The mechanism should be designed with the features of 360° revolving type. Seat back tilting ratio of 1:1.5, front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment,5-position locking with anti-shock back mechanism, which prevents the backrest from impacting the user when the lock should be released. Static seat depth adjustment = 5.0 ± 0.5cm with 5 position locking. It has an adjustment stroke of 9.0 ± 0.3cm. The bellow should be 1 piece and blow moulded in black polypropylene. The pedestal should be made of die-cast aluminium with buffing finish. It should be fitted with 5nos. twin wheel castor. The pedestal should be 67.0 ± 0.5cm pitch-centre dia. (77.0 ± 1.0cm with castors). The twin wheel castors should be injection moulded in black nylon. Overall Dimensions of Chair-Seat Height - min 49.9 to max 58.9 cm. Height - min 128.0 to 137.0 cm. Width & Depth of Chair as measured from pedestal - Width 77 cm and Depth 77 cm.

Supplying and placing in position Static Visitor Chair. The seat should be made up of 1.2 ± 0.1cm thick hot pressed plywood and upholstered with leather and moulded polyurethane foam. The back foam should be designed with contoured lumber support for extra comfort. Back size: 53 cm(w) x 73 cm(h) seat size: 54.6cm(w) x 49.0cm(d). The hr polyurethane foam should be moulded with density = 45 ±2 kg/m³ and hardness load 16 ± 2 kgf for 25% compression. The fixed type mechanism should be made with a 0.8 ±0.05 cm thick hr steel spine welded to it and black powder-coated ( dft 40-60 microns ).The under structure should be made up of m.s.e.r.w. elliptical tube of size 4.5 ± 0.03cm x 1.9 ± 0.02cm x 0.25 ± 0.025cm welded to m.s.e.r.w tube of ∅ 1.6 ± 0.02cm x 0.2 ± 0.016cm thk. the under structure should be powder coated ( dft 40-60 microns ) in silver metallic gray. Overall Dimensions of Chair Seat Height -46.0cm.Height -99.5cm.Width & Depth of Chair as measured from pedestal - Width 63.0 cm and Depth 69.0 cm.

Supplying and Placing in position 30 seater conference table of the following specifications, with size shall be 14 quantity of 2 STR component -1350 x 710 x 740, 2 Qty 1 STR 675 x 710 x 740 and one 1800W - 1800 x 850 x 740 head table with Work Surface-Made of 36mm thick MDF one side prelaminated board conforming to IS14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Full length access panel is provided with soft closing hinges in line with worktop edge. Worktop is available in various shapes. The under structure consist of mixture of 18mm and 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty should be made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cut out for Standard Anchor Roma 4 module should be provided for electrical fittings in Straight two seater and single seater modules below access flap per seat. The table should be equipped with cables cubbies along with cable retractors as standard offering for 1800mm head modules and table should be with basic switch socket cut outs.

Supplying and Placing in position Three Seater Sofa of size Width (W): 206.0 cm Depth (D): 90.5 cm Height (H): 85.5 cm. Seat Height (SH): 45.0 cm. The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back should be made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of super soft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under structure should be made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly should be mounted over under structure for cushioning purpose. It should a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic end cap.

Supplying and Placing in position Single Seater Sofa of size Width (W): 86.0 cm. Depth (D): 90.5 cm. Height (H): 85.5 cm. Seat Height (SH): 45.0 cm. The seat is made up of PU foam in Density 28 ±2 kg/cu.mtr with an additional top layer of super soft PU foam in Density 32 ± 2 kg/cu, upholstered with fabric or leatherette. Back should be made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer of super soft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Under structure should be made up of 1.2±0.1 cm. thick hot pressed plywood [moisture resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly should be mounted over under structure for cushioning purpose. it should a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic end cap.

Supplying and Placing in position Centre Table of size Width=112.0 cm, Depth=60.0 cm, height=34.9 cm. The top should be 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for forcing with under structure and under structure should be of welded assembly made in SS202 grade Dia. 12±0.04 as per IS:1762. it should be 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for focing with understructure and understructure should be of welded assembly made in SS202 grade Dia. 12±0.04 as per IS:1762.Width of table= 112.0 cm, Depth=60.0 cm, height=34.9 cm.

Supplying and Placing in position Corner Table of size Width= 60.0 cm, Depth=60.0 cm, height=34.9 cm. The top should be of 10 ±0.3 mm thick black tinted Toughened glass UV glued with bushes made in SS 202 grade for forcing with under structure and under structure should be of welded assembly made in SS202 grade Dia. 12±0.04 as per IS:1762.