Puducherry Adidravidar Development Corporation Limited Tender

Code No.10.16.1 Steel work in built up tubular (round,square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - hot finished welded type tubes

Code.No 11.61 Providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over 20mm thick cement mortar 1:4 (1 cement : 4 sand) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \ Dazzle \ Technic)

Code.No 12.50 Providing & fixing precoated galvanised iron profile sheets (size, shape, and pitch of corrugation as 0.50mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required .

Code.No 12.51.4 Providing and fixing precoated galvanised steel sheet roofing accessories 0.5mm (+0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns using self drilling / self tapping screws complete - Barge board (Upto 300 mm)

Code.No 12.51.5 Providing and fixing precoated galvanised steel sheet roofing accessories 0.5mm (+0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns using self drilling / self tapping screws complete - Crimp curve

Code.No 13.1.1 12mm cement plaster of mix -1:4 (1 cement

Code.No 13.61.1 Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Code.No 12.41.2 Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10mm gap for thermal expansion, (i) Single socketed pipes - 110 mm diameter

Code.No 12.42.6.2 Providing and fixing on wall face each unplasticised - PVC moulded fittings /accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe

Code.No 10.25.1 Steel work welded in built up sections /framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required all complete

NPSR Providing and fixing special shaped rain water gutter made out of aluminium sheets of 1.25mm thick of size 35cm of vertical height on one side, 25cm width at bottom and 30cm vertical height on other side in which 10cm of width is bended to "L" shape to suit with existing roofing sheet bottom side. the joints of the gutter lengths are provided with 15cm lap jointed with special resin packing with stainless steel boltings are packed with sealents for 100% leak proof. both the ends of the gutter is closed with same aluminium sheets in the required shape and pipe line fixing provision is provided on both ends for fixing rain water pipes. the gutter assembly is placed in the clamps made out opf 40mm x 6mm MS flats bended to the gutter shape and welded with th eexisting roof trusses and purlins of not less than 1.2 m spacings. the bottom side of the gutter assembly is supported with M.S. angle of size 40mm x x40mm x 6mm of not less than 3m spacings rate includes all the materials, labour charges, aluminium sheet bending charges, stainles steel bling in joints sealent packing, errecting to the required height and location with welding at site, transportation etc., complete. Rate approved vide Lr.No.364/PW/SEI/AE(P)-II/F.No.221/10-11. dt.22.12.2010.

NPSR Bending the 50mm dia pipes to the required arch shape using Hydraulic Bending machine and toos etc., complete.

NPSR Providing and fixing G.I sheet of required size and shape to the existing ornamental gate of sheet thickness 1.6mm (16SWG). The Rate includes all materials labour charges such as cutting, welding and grinding at site using welding machine, cutting machine and grinding machine and transportation etc., complete. Rate approve vide Lr. No.684/PW/SEI/AE(P)-I/F.NO.300/2012-13. dt.30.03.2013.

NPSR Supply and fixinf of 20-24W LED tube light fitting. Make :Philips/havells/ Wipro. Approved no.352/PW/SE-1/AE(P)

Code.No 1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required - 25mm

Code.No 1.27.5 Supplying and fixing following size / modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required - 8 module (125 mm x 125 mm)

Code.No 1.17.1 Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface / recessed steel / PVC conduit as required - 1 X 1.5

Code.No 1.17.12 Supplying and drawing following size2.8s of FRLS PVC insulated copper conductor single core cable in the existing surface / recessed steel / PVC conduit as required -3 x 2.5 sq.mm

Code.No 1.24.1 Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required - 5/6 A switch

Code.No 1.24.5 Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required - 6 pin 15/16 A socket outlet