Puducherry Adidravidar Development Corporation Limited Tender

Code no: 2.2.2.3 Supplying and fixing 6 amps to 32 amps rating ,Double pole,240 volts,'c' series,miniature circuit breaker suitable for lighting and other loads of following poles in the existing MCB DB complete with connections,testing and commissioning etc. as required. Make:Siemens/ABB/L&T Hager

Code no: 1.3.17 Supplying and fixing of the following sizes of Teak wooden board on recess including cutting the wall and finishing the surface good the same as required - 375mm X 300mm X 50mm. Deep

Code no: 1.6.17 Providing and fixing of following size phenolic coated sheet on existing wooden board: - 375mm X 300mm X 3mm Thick

Code no: 3147 Supplying and fixing of 32A cutout fuse unit Make: Kundan

Code no: 2.4.2 Supplying and fixing of sheet steel, DP switch Rewirable porcelain fuse unit, 230volts including drilling holes on the board, connections, earthing the body etc. as required:- 32Amps double pole main switch.Make:Standard/Havells

Code no: 3.1 Earthing with G.I.medium pipe 3.0 mt long and 40mm dia including accessories 250 x 50 x 6 mm G.I clamp with 12mm bolt, nut and washer for connecting earth wire, RCC ring enclosure and cover plate complete as required:-

Code no: 3.3 Extra for salt and charcoal for pipe earth electrode as required:-

Code no: 1808 8 SWG copper wire (4.0 mm dia.)

Code no: 1.7.2.1 Supplying and fixing 3 plate, 5 amp.ceiling rose on the existing junction box/wooden block including connections etc. as required.Make: Kundan/Anchor/Vinay:-

Code no: 3010 PVC round Plate.Make: Kundan/Modi

Code no: 1.5.1 Supplying and drawing of 1.5 sqmm. FR PVC insulated, copper conductor, single core cable in the existing surface/recessed, PVC/steel conduit/PVC casing and capping as required.Make: Finolex/Polycab:-

Code no: 1.5.2 Supplying and drawing of 2.5 sqmm. FR PVC insulated, copper conductor, single core cable in the existing surface/recessed, PVC/steel conduit/PVC casing and capping as required.Make: Finolex/Polycab:-

Code no:NPSR Supplying and fixing of pillar lights:Jaquar ground burial LED light fitting made up of die cats aluminium transparent tempered glass diffuser .304 stainless steel finish ,90 to 260 V , 1 x10w LED warm white . CAT Ref: LGBL05R101XW

Code no: NPSR Supplying and fixing of Jaquar wall washer LED light fixture made up of die cast aluminium tempered glass diffuser , IP54 matt grey finish , 90-260v AC 1x3 w LED . Cat Ref: LWWWL01S103XW

Code : NPSR Supplying and fixing of Jaquar strip light outdoor application of 5 w/ mtr, IP67,90 to 260VAC Cat Ref: LSTP04X005XW Warm white .Price mentioned for 5 mtr strip and driver for 5 mtr strip

Code :NPSR Supplying and fixing of Jaquar LED Highbay 70 w with glass made up of Die cast Aluminium with IP65 protection surface mounting type with operation voltage at 140 v to 270 v with COB light source Driver efficiency 80% , PF 0.95 , led Lumen efficacy 120 Lumen/w , surge protection 2.5 kv.

Code : NPSR Supplying and fixing of jaquar COB LED Flood light luminarie 30w made up of die cast housting & tougned glass, Operating voltage should be 110 v to 270 v AC,PF0.9

Code : NPSR Supplying and fixing of jaquar COB LED Flood light luminarie 50w made up of die cast housting & tougned glass, Operating voltage should be 110 v to 270 v AC,PF0.9

Code no: 3210 Supplying of 2 x 16sqmm armoured aluminium U.G cable - 1.1 KV grade.Make:Finolex/Polycab

Code no: 11.15.2 Supplying and making end termination with copper gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1KV grade as required: 2 X 16 Sq.mm

Code no: 11.1.1 Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of size not exceeding 25sq.mm direct in ground including excavation, sand cushioning, protective covering and refillilng the trench etc as required in Mud Road

Code no: 3212 Supply of 4 x 25sqmm armoured aluminium U.G cable - 1.1 KV grade.Make:Finolex/Polycab

Code no :11.1.2 Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of size not exceeding 25sq.mm direct in ground including excavation, sand cushioning, protective covering and refillilng the trench etc as required in Bituminous Road

Code no: NPSR Creating the groove patern in the fin using san an cement base slurry of ration 1:1 using 00mm templet,maintaining te corner an groove right angle.The groove between each plate will be 18mm alarount. White cement to be use to avoi the Crack where ever require.using 8mm bit ro for below the plate each corner for the aitional support while plastring.The plate thickness will be minimum 18mm incluing quering as irecte by the engineer in charge etc.complete

Code no: NPSR To prepare top an bottom captial using fine san cement slurry over the rough plaster surface. Get impress the pattern of captial using pre mole templete. Each size of the captial is 600*600mm,proviing 7mm cornice in the top an bottom of the captial by using same kinf of material.Partly while cement to be use to avoi racks. Using 8mm bit rot in the each corner of the captial to hol the captial at the time of creating.Using mm wanger brush to corect the insie corners to be sharp an straight,remove the unwante slurry immeiately . inluing quering as irecte by the engineer in charge etc.complete

Code no: NPSR Proviing the flute type groove in the pillar using rough plaster alaroung using fine san,the with of the each groove will be 18mm,the groove will be break at the level of top an bottom of te pillar. Partly white cement to be use to avoi the cracks. wire mesh to be use if require . incluing quering as irete by the engineer in charge etc.complete

Code no: NPSR Proviing the arh top mouling as per esign using fine san cement base slurry,over the rough plaster base.Using kani kal brick of size 75*12mm to create the patern, using 8mm bit ro in the each row to hol the support of bricks.Maintain the two level of cornice of size 75*50 an 125*75 as per esigne,using rough plaster in the inner level an fine plaster in the external level.inluing quering as irecte by the engineer in charge etc.complete

Code no: NPSR Constructing the roof top wall mouling work using kani kal bricks an fine san plaster AS per esign of size 500mm hight.incluing quering as irecte by the engineer in the charge etc.complete

Code no: NPSR Parapet wall brick work an plastering with borer butten cutting work as per eign an etail an size -700mm height,the base material like fine san, cement slurry,an kany kal brick of size 75*125, using 8mm cut for aitional support an holing the patern.incluing quering as irecte by the engineer in charge etc,complete

Code no: NPSR Proviing the parapet wall mouling as per esign using fine san cement base slurry,over the rough plaster base.Using kani kal bricks of size 75*125mm to creat the patern,using 8mm bit ro in the each row to hol the support of bricks.Maintain the two level of cornice of size 75*5 an 125*75 in the top an bottom of the wall as per esigne,using rough plaster in the inner level an fine plaster in the external level.inluing quering as irete by the engineer in charge etc.complete

Code no: NPSR Parapet wall top moulding of size 375 mm as per Design and detail including as directed by the Engineer in charge etc. complete.

Code no: NPSR Two level of roof bottom plastering using rough in base level and fine sand plaster in the top level to creat the paterns.Maximum thickness of plastering will be 18 mm .including quering as directed by the Engineer in charge etc. complete.

Code no:NPSR Constructing and placing the kalasam as per design and size-600 x 825 mm including quering as directed by the Engineer in charge etc. complete.

Code no: 14.72 Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story height made with 40mm dia M.S. tube 1.5m centre to centre horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S.staircase system in the scaffolding for working platform etc. and maintaining it is a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc. wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as approved. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. (To be used for maintenance work judicially necessary deduction for scaffolding in the existing item to be done)

Code no: 13.26A Providing and applying ready mixed wall putty (JK / BIRLA ) of 2mm thickness over plastered surface to prepare the surface even and smooth complete

Code no: 13.43.1 Applying one coat of cement primer of approved brand and manufacture on wall surface - Cement primer

Code no: 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade - New work (Two or more coats applied @ 1.43 ltr / 10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 qm).