Public Works Department Tender

Code No. 9.95.3:- Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete : 100x75x4mm

Code No. 9.118.1:- Providing and fixing to existing door frames - 24mm thick factory made PVC door shutters made of styles and rails of a UPVC hollow section of size 59x24mm and wall tickness 2mm +or- 0.2mm with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S.galvanised / plastic brackets of size 75x220 mm having wall thickness 1.0mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20mm and 1mm +or-0.1mm wall thickness .The lock rail made up of 'H' section , a UPVC hollow section of size 100x24 mm and 2mm + or - 0.2mm wall thickness fixed to the shutter styles by means of plastic / galvanized M.S.'U' cleats. The shutter frame filled with a UPVC multi - chambered single panel of size not less than 620 mm, having over all thickness of 20mm and 1mm + or -0.1mm wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanized M.S.rod and fastened with nuts and washers,complete as per manufacturer's specification .(For W.C. and bathroom door shutter)

Code No. 11.36B:- Providing and fixing 1st quallity ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacture of approved make (Jhonson / Asian / Somany / Nitco) in all colours, shades of size 300 x 450 mm as approved in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm. Including pointing in white cement mixed with pigment of matching shade complete. - size 300x450mm

Code No. 11.40:- Providing and laying rectified glazed ceramic floor tiles 300x300mm or more(thicknes to be specified by the manufacturer) of first quality conforming to IS: 15622 of approved make (Somany / Nitco / Jhonson ) in all colours shades except white, ivory, grey, fume red brown laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete.

Code No. 11.40.1:- Providing and laying rectified ceramic rustic / matt finish floor tiles 300x300 mm or more (thickness to be specified by the manufacturer ) of 1st quality conforming to IS:15622 of approved make ( Somany / Nitco) in all colours shades laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., Complete

Code No. 12.43.1:- Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1 cement : 4 coarse sand) and making good the wall etc. complete. 75mm

Code No. 12.43.2:- Providing and fixing unplasticised - PVC clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm.

Code No: 13.60.1B:- Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade - two or more coats on new work

Code No. 13.61.1:- Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or more coats on new work.

Code No: 14.1.1:- Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - With cement mortar 1:4 (1 cement : 4 fine sand)

Code No. 14.43:-Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Code No: 15.12.1:- Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within50 m lead - Of area 3 sq. metres and below.

Code No.: 15.56:- Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50m lead.

Code No. 17.1.1:- Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100mm sand cast iron P or S trap, 10 litre low level white P.V.C . Flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : white vitreous china Orissa pattern W.C .pan of size 580X 440mm with integral type foot rests.

Code No: 17.2.1: -Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever, conforming to IS: 7231, with all fittings and fixtures complete) including cutting and making good the walls and floors wherever required. W.C pan with ISI marked white solid plastic seat and lid.

Code No. 17.10.2.1;- Providing and fixing stainless steel AISI 304 (18/8) Kitchen sink as per Is 13983 with CI brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required - Kitchen sink without drain board - 610x510 mm bowl depth 200mm.

Code No. 17.25.2:- Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings flat back wash basin of size 550 x 400mm.

Code No. 17.28.1.1:- Providing and fixing PVC waste pipe for sink or wash basin including PVC waste fittings complete - Semi rigid pipe - 32mm dia

Code No. 17.78.1:- Providing and fixing CP brass health fauce of approved quality - 15mm nominal bore

Code No. 18.8.2:- Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fitting with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete (Concealed work including cutting chases and making good the walls etc.) - 20mm nominal outer dia pipes.

Code No. 18.9.5:- Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this included jointing of pipes & fittings with one step CPVC solvent cement,trenching refilling & testing of jointscomplete (External work) - 40mm nominal outer dia pipes.

Code No. 18.54.4:- Providing and fixing PTMT bib cock of approved quality and colour 15 mm nominal bore, 90mm long weighing not less than 93gms.

18.55.2:-Providing and fixing PTMT stop cock of approved quality and colour 20mm nominal bore, 89mm long, weighing not less than 88 gms.

Code No.: 18.56.2:-Providing and fixing PTMT pillar cock of approved quality and colour 15 mm nominal bore, 125mm long foam flow weighing not less than 120 grams.

Code No. 19.33.1C:- Providing and fixing on wall face/column face unplasticised- PVC moulde fittings/ accessories for unplasticisd – PVC soil and waste pipes conforming to IS:14735-1999 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion - bend 110mm

Code No. 19.33.1D:- Providing and fixing on wall face /column face unplasticised - PVC moulded fittings/accessories for unplasticisd – PVC soil and waste pipes conforming to IS:14735-1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend with door 110mm

Code No. 19.33.2C:- Providing and fixing on wall face / column face unplasticised - PVC moulded fittings / accessories for unplasticisd - PVC soil and waste pipes conforming to IS:14735 – 1999 including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion - bend 75mm

Code No. 31.160.1G:- Providing, laying and jointing UPVC pipes (Finolex/Jain) (1 Mpa) conforming to IS specification 4985 and ISI marked including transportation to the site, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends, tees, threaded pieces, couplers,reducer, endcaps etc., complete all as per IS and CPWD specification. - 75mm dia.

Code No. 31.161.1F: - Providing, laying and jointing UPVC pipes (Finolex/Jain) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers, reducer,endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Code No: 31.178.1D: - Providing and fixing in position UPVC fabricated bend (Finolex/Jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110 mm dia

Code No. 31.179.1B:-Providing and fixing in position UPVC fabricated bend (Finolex/Jain)(1 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc, complete – 75 mm dia.