Public Works Department Tender

Supplying and fixing of 1x3x6 sqmm (single run) PVC insulated copper submersible flat flexible cable of Finolex make complete.-12.5HP to 20HP pumpset

Supplying and fixing of 7.5KVAR power capacitor (CG/L&T/Siemens make) for 15 HP motor complete.

Supplying of 3.5/4x50 sqmm underground cable (Paragon/suncab/Empire) complete.-suitable for (30HP to 40HP pumpset)/(upto 40KVA Genset).

Laying of UG cable and providing termination of cable joint with suitable cable gland,cable socket etc., complete - 3.5/4 x 50 / 3.5/4 x 70 sqmm cable.

Supplying and fixing of meter board of size 600mmx900mmx150mm on suitable angle frame with suitable water proof plywood 12mm thick for receiving ED supply. The board frame shall be painted and covered on all sides by 16 gauge M.S. sheet and fixed with 3 Nos. of 100 Amps fuse carrier (Havells/Standard/ Anchor make) with screws etc., complete.

Supplying and fixing of teak wood aerial board with 100 Amps HRC fuse base and fuse link and suitable post clamp to hold the G.I. Pipe with electric post including bolts and nuts etc., complete.

Making earth pit of G.I. pipe for earthing in earth pit with 40mm dia. G.I. pipe medium class of length 3.05m perforated with 46 Nos of 12mm dia. holes, pipe lowered in bore holes of 150mm dia. and filled in with charcoal and salt in alternative layer of 300mm, the top of G.I. pipe shall be clamped. Earth pit shall be provided with 60cm dia precast ring with 60cm depth alround,covered with R.C.C. precast slab etc. as per I.E. standards.

Supplying and fixing of copper wire 8 SWG (4 mm dia) for earthing arrangements including bolt and nuts etc., complete.

Providing and fixing 50 mm dia GI pipe (Class B) conforming to IS 1239 (Part 1:1990) with GI fittings including trenching, refilling etc., complete for UG cable duct.

Supplying and fixing of pole clamp to hold the G.I. Pipe with electric post.

Supplying,fixing and lowering into the borewell high tensile threaded PVC column pipes which are to be connected to the submersible pump,including labour charges,jointing materials etc.,complete.-75/80 mm dia

Supplying and fixing of C.I. adopter which is to be connected to submersible pump delivery pipe.-75/80 mm dia

Supplying and laying of 16mm dia nylon rope for holding of motors.

Supplying and laying of 40mm dia. PVC pipe (Class 3 - PN 0.6 Mpa) conforming to IS 4985 : 2000 for inserting submersible cable from borewell to starter.

Supply and fixing of 80/100mm dia. M.S. erection clamps of size 80mmx12mm with bolts, nuts, washer etc., complete.

Erection, testing and commissioning of motor and pumpset complete.The rate includes obtaining electricity service connection from Electricity Department also.

Supply and providing of fabricated steel Kiosk of internal dimension 2.20 x 1.90m with front and rear height of 2.40m and 2.10m respectively. The fabrication of the kiosk is to as per the details below:- The corner pillar of the Kiosk shall be of single equal M.S. angle 50x50x6mm tied up at the top, bottom and middle with 40x40x6mm angle, intermediate support of M.S. angles (2 Nos) of 40x40x6mm in all 4 sides and stiffener in vertical with 40x6mm flats and shall not exceed 0.50m C/C. For roof 2 nos. of 40x40x6mm angles to a length of 1.90 mts. each with 3 nos. of 40x6mm flat for a length of 2.20 mts. Shall be provided. For front door portion an extra angle of 40x40x6mm of 2.40m as vertical and as horizontal lintel of 0.65m of the same angle are to be provided. The door shall be of 0.60mx1.85m with 40x40x6mm angle on all the four sides with 1 no. of intermediate horizontal angle of 40x40x6mm with cross stiffener of 40x6mm flats for the doors shutters. The sides of the Kiosk shall be of 18SWG GI corrugated sheet and roof shall be colour coated galvalume sheet of 550 M.P.A. yield of AZ 150 strength formed as per patterned steel rib profile with the depth of 31 mm pitch of 250mm and overall width of 1060 mm and thickness 0.5mm with required J or C hook bolts & nuts 8mm dia.

The rate shall included the cost of all materials, labour, fabrication charges including providing of lacking arrangements for the door painting cost with steel primer and paint charges for the angles, painting two coats of enamel paint both side and outside the Kiosk, transportation to the newly erected borewell site in villages in Puducherry region etc. and erected on platform as directed by the Engineer in charge.

The foundation brick work in CM 1:4 will be constructed in 23 cm wall for a height of 60 cm over foundation concrete PCC 1:5:10 for a width of 60 cm and 15 cm thick. The inside pump shed flooring will be laid in PCC 1:2:4 in 50mm thick over a red earth filling of 15 cm thick and PCC 1:5:10 of 10 cm thick. The outside area will be plastered in cement mortar 1:4, 12 mm thick etc. complete as directed by the Engineer in charge.

Providing and fixing of 65mm Godrej Navatal lock of 6 levers etc complete

Providing and laying Ductile Iron Double flanged pipes of class K9 (Electro steel/ Sripipes/ Jindal/ Electrotherm) conforming to IS specification 8329/2000 and ISI marked suitable for flanged joints in good condition including transportation of D.I.pipe from production centre/company to the site at UT of Puducherry, lowering to the trenches(or fixing in over head tanks above ground level) laying to proper grade and alignment, testing of joints with required testing equipment etc.,complete all as per IS12288 and CPWD specification . (earth work and jointing of pipes with rubber insertion will be paid separately) -100mm dia.

Providing and fixing C.I. Ball type non return valve (PN 1) conforming to IS 318 & IS 1363, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing C.I. sluice valve (PN 1.6) (with handwheel) conforming to IS 14846 and ISI marked, with bolts, nuts, rubber insertion etc.,complete (the tail pieces if required will be paid separately) - 100 mm dia.

Providing and fixing in position flanged standard D.I. specials (Electro steel/Sripipes/Jindal/Kiswok) such as tees, bends, collors, tapers, caps etc.conforming to IS specification 9523/2000 and ISI marked - 100 to 300mm dia.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 100mm diameter pipe.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m - all kinds of soil - pipes, cables etc , exceeding 80mm dia but not exceeding 300 mm dia

Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - bituminous road

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:4:8 or leaner mix (including equivalent design mix)

Earth work in excavation by mechanical means (Hydraulic excavation) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10sqm on plan) including getting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m - all kinds of soil

Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including cost of solvent cement, excluding UPVC specials such as bends, tees, threaded pieces, couplers, reducer, end caps etc., complete all as per IS and CPWD specification. - 140mm dia.

Providing and fixing in position UPVC fabricated bend (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked, including labour charges for jointing, jointing materials etc, complete - 140 mm dia

Providing and fixing in position UPVC fabricated coupler (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc, complete - 140 mm dia

Providing and fixing in position UPVC moulded tail piece without flange(Finolex / jain) (0.6 Mpa)conforming to IS 7834 part II and ISI marked, including labour charges for jointing, jointing materials etc, complete - 140mm dia

Providing and fixing mild steel flange including bolts, nuts, rubber insertion, labour charges etc,complete-125mm dia

Providing and fixing reducing mild steel flange including necessary bolts, nuts, rubber insertion, labour charges etc,complete-125 x 100mm dia

Making connection of uPVC distribution branch with Upvc main of following sizes by providing and fixing tee including cutting the pipe etc.,compete.-110 mm dia to 160 mm dia nominal bore.

Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50m - all kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Centring and shuttering including strutting , propping etc. and removal of form work for - foundations, footings, bases for columns

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Providing, laying and jointing G.I pipes of medium class (blue)(TATA, TNT, Nezone, Apollo, Zenith) conforming to IS specification 1239 part I and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, excluding GI specials such as bends, tees, elbow, coupling, reducer etc., complete all as per IS and CPWD specification. -80mm dia

Providing and fixing in position G.I. coupling (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked, including labour charges for jointing, jointing materials etc, complete - 80 mm dia.

Providing and fixing in position G.I. elbow (UNIQUE/R Brand/HB Brand/UI Brand) conforming to IS 1239 part II and ISI marked, including labour charges for jointing, jointing materials etc, complete - 80 mm dia.

Providing and fixing Cast iron flanges conforming to IS specification 1538 and ISI marked. - 80 mm dia.

Providing flanged joints to double flanged C.I./D.I. pipes and specials including necessary bolts, nuts, rubber insertion and testing of joints etc.,complete - 80mm diameter pipe.

Providing,laying , spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site , laying in uniform layer by manual means in sub-base / base course on well prepared surface and compacting with smooth 3 wheeled steel roller to achieve the desired density.

Cleaning the existing W.B.M. road surface including removing of binding material and other foreign matter with wire brushes and small picks, sweeping with brooms or soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 502.4.2 and 503.3.1 of MOST specification.

Cleaning of the existing black topped surfaces with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 503.3.1 of MOST specification.

Providing and applying tack coat on the prepared surface, heating bitumen in boiler and spraying the bitumen with sprayset fitted on bitumen boiler - on granular base such as WBM and WMM surfaces not bitumen primed. Rate of application 10kg/10sqm.

Providing and applying tack coat on the prepared surface, spraying the bitumen emulsion with spray set at 4.00kg/10sqm.As per clause 503 of Most specification.

Providing and laying open graded premix carpet 20mm thick on prepared surface in a single course as wearing course composed of specified size of stone aggregates premix with a bituminous binder in mini hot mix plant 6 to 10 tonne laying manually and rolling with power roller 8 to 10 tonne but excluding cost of primer/tack coat. As per clause no 509 of MOST specification.

Providing and applying liquid seal coat, type `A' comprising of a layer of bituminous binder, followed by a cover of stone chipping of specified grading and rolling with power roller 8 to 10 tonne. As per clause no 513 of MOST specification.