Public Works Department Tender

Code No. 13.43.1:- Applying one coat of water thinnable cement primer of approved brand and manufacturer on wall surface - water thinnable cement primer

Code No. 14.54.1:-Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work

Code No. 11.36C:-Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson /Asian / Somany / Nitco) in all colours ,shades of size 300 x 600 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x600 mm

Code No. 11.41.2B:-Providing and laying Soluble Salt vitrified floor tiles of size 600 x600 mm (thickeness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make (Nitco / Somany / Johnson /Asian ) in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) , including grouting the joints with white cement and matching pigments etc., complete - size of tile600x600mm

Code No. 11.48.2:- Grouting the joints of flooring tiles having joints of 3mm width,using epoxy grout mix of 0.70kg of organic coated filler of desired shade (0.10kg of hardener and 0.20 kg of resin per kg) , including filling / grouting and finishing complete -size of tile 600x600 mm

Code No. 11.42:-Deduct for not using 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles

Code No. 11.43:-Fixing glazed /ceramic / Vitrified floor tiles with cement based high polymer modified quick - set tile adhesive (water based) conforming to IS:15477, in average 3 mm thickness - ( Using 5 kg adhesive per sqm of tile area)

Code No. 15.23.1:- Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead - for thickness of tiles 10mm to 25mm

Code No. 14.1.1:- Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - with cement mortar 1:4 (1 cement : 4fine sand)

Code No. 16.115:-Applying two coats of cement based polymer modified bonding admixture (FOSROC or equivalent) over the existing RCC members after removing the plastering and cleaning the concrete surfaces and saturated with clean water. The cost including all materials labour charges

Code No. 17.3.1:-Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid,10 litre low level white vitreous china flushing cistern & C.P.flush bend with fittings & C.I. brackets , 40 mm flush bend , overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets , cutting and making good the walls and floors wherever required - W.C.pan with ISI marked white solid plastic seat and lid

Code No.17.7.9:-Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china surgeon type wash basin size 660x460 with single 15mm C.P.brass pillar taps with elbow operated levers ISI marked

Code No. 17.32.4:-Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 1500 x 450 mm

Code No. 17.78.1:- Providing and fixing CP brass health faucet of approved quality - 15 mm nominal bore

Code No. 18.22.1:-Providing and fixing C.P.brass shower rose with 15 or 20 mm inlet - 100 mm diametre

Code No. 18.8.2:-Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings , with one step CPVC solvement cement and the cost of cutting chases and making good the same including testing of joints complete - Concealed work , including cutting chases and making good the wall etc - 20 mm nominal outer dia pipes

Code No. 18.74.2:-Providing and fixing unplasticised P.V.C. connection pipe with PTMT nuts, collar, and bush of approved quality and colour - 15 mm nominal bore with 45cm lenghth

Code No. 18.53.1:- Providing and fixing C.P.brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931- 15 mm nominal bore

Code No. 18.54.2:-Providing and fixing PTMT bib cock of approved quality and colour - 15mm nominal bore, 122 mm long , weighing not less than 99 gms

Code No. 31.162.1D:- Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore /Nandi) (0.4 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including cost of solvent cement, excluding UPVC specials such as bends,tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Code No. 31.177.1D:-Providing and fixing in position UPVC fabricated bend (Finolex / jain)(0.4 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110 mm dia

Code No. 23.2:-Supplying and stacking of good earth at site including royality and carriage complete (earth measured in stacks will be reduced by 20% for payment)

Code No. 23.3:-Supplying and stacking sludge at site including royalty and carriage complete (sludge measured in stacks will be reduced by 8% for payment)

Code No. 23.9:-Mixing earth and sludge or manure in the required proportion specified

Code No. 23.20:-Filiing mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and levelling (cost of supplying earth and sludge or manure and mixing excluded)

Code No. 10.25.2:- Steel work welded in built up sections / framed work , including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Code No. 13.52.1:-Finishing with epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface ,etc.complete - on steel work

Code No. 10.6.3:-Supplying and fixing rolling shutters of approved make, made of required size M.S.laths, interlocked together through their entire length and jointed together at the end by end locks , mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to ISS :4454 -part 1 and M.S.top cover of required thickness for rolling shutters -80 x 0.90 mm M.S.laths with 0.90 mm thick top cover

Code No. 15.2.1:-Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Code No. 15.19:-Dismantling steel work manually / by mechanical means in built up sections without distembering and stacking within 50 metres lead

Code No. 4.1.2:-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Code No. 4.3.3:-Centring and shuttering including strutting , propping etc. and removal of form work for - columns, piers, abutments, pillars, posts and struts

Code No. 13.1.1:-12mm cement plaster of mix -1:4 ( 1 cement : 4 fine sand)

Code No. 14.67.1:-Finishing walls with premium acrylic smooth exterior paint with silicon additives of required shade - old work (two or more coats applied @ 1.43 ltr / 10 sqm) over existing cement paint surface

Code No. 11.61:-Providing and laying 22 mm thick factory made pre-polished cement concrete flooring tiles of required colour and design over 20 mm thick cement mortar 1:4 (1 cement : 4 sand ) and jointed with cement slurry mixed with an admixture of pigment to match the shade of the tile - (Endura \ Ultra \ Dazzle \ Technic)

Code No. 17.22B:-Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved a) 15 mm nominal dia

Code No. 9.1.2I:- Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) - Irul wood

Code No. 9.5.1.1M:-Providing and fixing panelled or panelled and glazed shutters for doors, windows, and clerestory windows, including ISI marked M.S.pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately , all complete - Malabar Ist class teak wood - 35 mm thick shutters

Code No. 9.7.1M:-Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors , windows and clerestory windows (area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick - Malabar Ist class teak wood

Code No. 9.96.1:-Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , with nuts and screws etc complete - 300 X 16 mm

Code No. 9.97.1:-Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete

Code No. 9.97.3:-Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 200 x10 mm

Code No. 9.97.5:-Providing and fixing aluminium tower bolts , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , with necessary screws etc. complete - 100 x10 mm

Code No. 9.118.1:-Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Code No. 16.118:-Supply and fixing of sliding windows at all levels made out from Unplasticised Poly vinyl chloride frame (UPVC) of natural colour (PRISTINE WHITE) with outer frame of size 40 x 56x40mm / 102 x 56x 40mm and for shutter frame of size 53 x 38 x37 mm for two track / three track sliding widows , with wall thickness of 1.8mm (+/-0.3mm).The section should be single glazing using (flush catch) single point locking. The gasket should be made of EPDM (Ethylene propylene dimonomer) and applying silicon sealents (GE make or wacker make) outside and acrylic sealent inside including single glazing of 5mm thick clear float glass . The sections should be reinforced with GI sheet of 1.5 mm thick with suitable drainage grouting

Code No. 15.13.1:-Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead - of area 3 sqm and below