Public Works Department Tender

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 fine aggregate)

15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine aggregate)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 fine aggregate : 4 graded stone aggregate 20mm nominal size)

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm, with two chromium plated brass brackets fixed with C.P.brass screws and PVC sleeves etc.,wherever necessary complete - 20mm dia

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc.complete - 75 x 47 x 1.80 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc complete - 150 X 10 mm

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc complete - 65mm

Providing and fixing bright finished brass handles with screws etc complete - 125 mm

Providing and fixing stainless steel (grade 304) railing made of hollow tubes, channels, plates etc., including welding ,grinding. Buffing, polishing and making curvature (whereever required) and fitting the same with necessary stainless steel nuts and bolts complete. i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.,)

Structural steel work in single section , fixed with or without connecting plate, including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer all complete

Structural steel work riveted , bolted or welded in built up sections , trusses and framed work , including cutting, hoisting , fixing in position and applying a priming coat of approved steel primer all complete

Providing and laying vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer) , with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer , in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6mm thickness , including grouting of joints (payment for grouting of joints to be made separately) - size of tile 600x600 mm

Providing and laying ceramic glazed floor tiles of size 300 x 300 mm (thickness to be specified by the manufacturer) , of 1st quality conforming to IS :15622, of approved make , in all colours, shades, except white , ivory, grey, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 fine aggregate), jointing with grey cement slurry @ 3.3 kg /sqm including pointing the joints with white cement and matching pigments etc., complete

Providing and laying 83 mm mm thick factory made rubber moulded hydraulic pressed paver block made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand , filling the joints with fine aggregate etc. all complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineerin- Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm, zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns using self drilling / self tapping screws complete - Crimp curve

Supplying fixing and commisioning of 2 HP monoblock pumpset slow speed single phase motor. The rate include the cost of pumpset , pumpset fixing in position and test run etc.complete

Providing, cutting & fixing to required shape and design 19mm thick plywood (BWR) for cupboard shutters/table top/ bottom/ sides/ partitions and the llike. The rate is inclusive of cost of materials, wastages, screws, nails, fevicol SH, special labour charges for making cupblard shutters/ furnitures and finishing the surface neat after fixing in required position as directed by the Engineer in charge

Providing and fixing decorative high pressure laminated sheet of plain/ wood grain in gloss/ matt/suede finish (centurylam 3808 AL) with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS: 2046 type S, including cost of adhesive of approved quality - 1.0mm thick. The rate is inclusive of GST and other taxes

Providing and fixing flat teak wood-I class reepers of size 20x6mm alround the edges of plywood. The rate is inclusive of cost of materials, wastages, labour charges for fixing, screws, nails, fevicol SH and finishing the surface neat after fixing etc., complete as directed by the Engineer in charge