Indira Gandhi Medical College And Research Institute Tender

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with necessary screws etc.complete : 125x75x4mm

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete: 150 x 10 mm

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. -125 mm

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2nos.of 150mm long brackets of 15x15mm M.S.square tube, the vertical door profiles to be reinforced with 19x19mm M.S.square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame.The door frame to be fixed to the wall using M.S.screws of 65/100mm size complete as per manufacturers specification

Providing and fixing to existing door frames - 30mm thick factory made solid both side prelam panel PVC door shutter consisting of frame made out of M.S.tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top & bottom rails.M.S.frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded prelam PVC 'C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick , 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, button and lock rails shall be provided either side of the panel. 10mm (5mmx2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, panelling of 5mm thick both side prelam PVC sheet to be fitted in the M.S.frame welded / sealed to the stiles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side , and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C channel using PVC solvent adhesive etc.complete manufactures specification & drawing

Providing and fixing of 65mm Godrej Navtal lock of 6 levers etc complete

Providing and laying fully vitrified floor tiles of size 1000 x 1000 mm (thickeness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make (Nitco / Rak / Johnson / Asian) in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete - size of tile1000x1000mm

Grouting the joints of flooring tiles having joints of 3mm width,using epoxy grout mix of 0.70kg of organic coated filler of desired shade (0.10kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete - size of tile 1000x1000 mm

Providing and fixing 1/2" tk Daikin mineral false ceiling tiles prima fine fissued regular edge or equivalent having fire propogation test of 'class O' as per B.S.476 part 6, with a flame spread of class A of US federal spec.SS/S/118B. Thermal conductivity at 0.045K cal/mhc of JIS A 1412. Noice reduction co efficient (NRC) of 0.55-0.6 of ASTM C 423,light reflectance of LR 1 (75% os ASTM C523) CAC at 36 of ASTM E 413 and asbestos free and humidity resistance of RH 99% of size 600x600mm with interlocking metal grid of hot dipped galvanized steel sections (galvanized at 170gm / sqm) with pre-finished in baked polyster paint , consisting of main runners of size 24x33 mm T-section made of 0.27mm tk (minimum) sheet spaced at 1200mm centre to centre and secondary T hot dipped galvanized steel section of size 28x24mm made of 0.27 mm tk (Minimum) sheet with pre finished in baked polyester paint to be interlocked in between main runner at 600mm centre to center to form overall grid of 600x600mm laying 15mm tk mineral fibre false ceiling tiles in the grid suspended by hanger rods 60cm long with bolts @ 1.2m c/c including cutting / making openings of services like fittings, diffusers , grills, smoke detectors, etc including providing necessary wall angle of size 19x19x0.45 mm on all four sides including scaffolding etc., complete as directed by the engineer in charge, ceiling upto 6.5m heights

12 mm cement plaster of mix - 1:6 (1 cement : 6 fine sand)

15 mm cement plaster of mix - 1:6 (1 cement : 6 fine sand)

Providing and applying ready mixed wall putty (JK / BIRLA) of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Applying one coat of cement primer of approved brand and manufacturer on wall surface:- Cement primer

Wall painting with plastic emulsion paint - Premium of approved brand and manufacture to give an even shade: -two or more coats on new work.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Acid cleaning for the existing Mosaic floors , glazed tiles work and removing the stains and decays to give a glassy look etc complte (The Acid used shall be 32% concentrated hydrochloric acid after taking on the precautionary measures)

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litres / 6 litre (adjustable to 4 litre / 8 litres), including seat cover , and cistern fittings , nuts, bolts and gaskets etc complete.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350xmm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and CP brass spreaders with brass unions and G.I clamps complete, including paintings of fittings and brackets, cutting and making good the walls and floors wherever required. One urinal basin with 5 litre white PVC automatic flushing cistern.

Providing and fixing wash basin with CI brackets, 15mm CP brass pillar taps 32 mm CP brass waste of standard pattern including painting of fittings and brackets, cutting and making good the walls wherever required White vitreous china angle back wash basin size 600x480mm with single 15mm CP brass pillar taps.

Providing and fixing CP brass health faucet of approved quality - 15mm nominal bore

Providing and fixing CP brass shower rose with 15 or 20 mm inlet 150 mm diameter.

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore.

Providing and fixing CP brass bib cock of approved quality conforming to IS 8931 -15mm nominal bore.

Providing and fixing CP brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms - 15mm nominal bore.

Providing and fixing CP brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 - 15 mm nominal bore.

Providing and fixing CP brass stop cock (concealed) of standard design and of approved make conforming to IS 8931 - 15mm nominal bore.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) : For Fixed potion. - Anodised aluminium (anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/ neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P.brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and panelling to be paid for separately) : For Shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately) - Annadised aluminium (anodised transparent or dyed to required shsde according to IS : 1868, Minimum anodic coating of grade AC 15

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) : with float glass panes of 6 mm thickness.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS: 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.-With stainless steel cover plate

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partition etc. with 6mm thick clear float glass both side having 12mm air gap including providing EPDM gasket, perforated aluminium spacers, desiccants, silicon sealant (both primary and secondary sealant) etc. as per specificatrions, drawings complete.

Providing and fixing 100mm X 35 mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete

Providing and fixing PVC switch lock of 100mm length for aluminium sliding windows

Providing and fixing 8mm thick prelaminated cement bonded particle board in panneling fixed in aluminimum doors, windows, shutters and partition frames with C.P. brass / stainless steel screws etc., complete as per drawings. Prelaminated particle board with decorative lamination on both sides.