Department Of Local Administration Tender

Code No. 4.1.10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Code No. 4.3.1 Centring and shuttering including strutting , propping etc. and removal of form work for - foundations, footings, bases for columns

Code No.13.16.1 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Code No. 15.2.1 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/cequivalent design mix)

Code No. 15.7.4 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Code No. 6.1.MO Cleaning the existing W.B.M. road surface including removing of binding material and other foreign matter with wire brushes and small picks, sweeping with brooms or soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 502.4.2 and 503.3.1 of MOST specification.

Code No. 6.2.MO Cleaning of the existing black topped surfaces with brooms, soft brushes and finally dusting with old gunny bags and/or compressed air to receive bituminous treatment. As per clause no 503.3.1 of MOST specification.

Code No. 5.1 Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 Kg/sqm using mechanical means. (As per MoRTH specification, 4th Revision)

Code No. 5.2 Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg. per sqm. on the prepared bituminous / granular surface cleaned with mechanical broom. (As per MoRTH specification, 4th Revision)

Code No.5.3B Providing and laying bituminous macadam with hot mix plant of capacity not less than 40 -60 TPH using crushed aggregates of specified grading premixed with bituminous binder, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 507.7 of MoRTH specification, 4th Revision, to achieve the desired compaction. - using grade II metal and bitumen 60/70 grade.

Code No. 5.7B Providing and laying semi-dense bituminous concrete with HMP of capacity not less than 40 - 60 TPH using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause 508 of MoRTH specification, 4th Revision, complete in all respects - Using grade-II material and using birumen 60/70 grade.

Code No. NPSR (SE Approved Rate) Fabrication, supply and fixing of village/informatory name board of size 1.06mts x 0.61mts. The width of the board is tapered at 0.80mts upto 1.06mts to give the triangular shape at one end with high intensity reflective sheeting of required color encapsulation on aluminium sheet of not less than 2mm thick suitably supported and framed with 25mmx 25mmx 3mm AISI 316 grade stainless steel angle and the board frame is supported alround with AISI 316 grade stainless steel pipe of 38.10mmdia (outer dia & 2mm wall thickness). The Village names/street names, lettering and symbols will be provided by High Intensity grade white sheeting. The board is supported by Two Nos. of 63.5mm dia post S.S pipes for 2.0mts height with same dia Dummy plate arrangement at the top. The board framne and post pipes are welded by Tig welding with necessary polishing etc, and M.S pipe of 50mm dia for a length of 35cm will be welded at the bottom of the posts and fixed in a ground pit of size 0.45x045x0.45mts with P.C.C 1:2:4. Rate including all the materials, S.S welding, Grinding, Polishing, fabrication charges, conveyance etc except Earth work and P.C.C charges, complete