Department Of Local Administration Tender

CODE NO. 6.1.1 (Addendum) Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

CODE NO. 8.12 Providing and laying flamed finish granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18mm thick stone slab over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as - flamed finish granite stone slab Jet black

CODE NO. 11.40.1 Providing and laying rectified ceramic rustic / matt finish floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make (Somany / Nitco) in all colours , shades, except white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc., complete

CODE NO: 13.2.1 15mm cement plaster on the rough side of single or half brick wall of mix - 1:4 (1cement : 4 fine sand)

Code No.13.46.1 Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022 -Supply and Fixng of Mini Ski: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.40 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. The Standing Bars 991 mm and Dia 60 mm fabricated from 40 O.D. galvanized steel pipes Upper part of Support Handrails of size 1.04 m high and Dia 38 mm fabricated from 40mm O.D. and 32 mm O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably.Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.07 m x 0.78 m x 1.40 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022-Supply and Fixng of Arm and Pedal Bike: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Horizontal Structural post of length 1.10 m supporting Upright structural posts of height 1.23 m and Dia 60mm is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Pedals of size 108 mm & Bars of size 197 mm. The poles are welded on to a base plate made from steel with 60mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.43 m x 0.65 m x 1.23 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022 -Supply and Fixng of Waist Twister: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.35 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Circular Handrail Dia 42 mm fabricated from 42 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably.Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the 0maintenance guide. Equipment Dimensions: 1.44 m x 1.29 m x 1.35 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 0certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022- Supply and Fixng of Rider: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 0.5 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. A single seat of size 330 mm x 250 mm fixed to the top of the vertical post and two Pedals & Bars of size 145 mm x 50 mm and Dia 38 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 0.91 m x 0.65 m x 1.27 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022-Supply and Fixng of Seated Chest Press: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.88 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two pair of U-Shaped Bars of 1.02 m and Dia 40 mm while the handles are placed at a spacing of 698 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.82 m x 0.69 m x 1.88 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS tes marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022-Supply and Fixng of Health Walker: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Foot Rest of size 361 mm x 161 mm are attached to the Standing Bars 957mm x 60 mm fabricated from 60 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. An Internal limiter prevents the equipment from moving uncontrollably. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.18 m x 0.553 m x 1.25 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022- Supply and Fixng of Self Weighted Rower: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Horizontal bars of length 1.26 m is to be schedule HOT DIP Galvanized steel with a 60mm O.D. and 2.2mm (wall) thickness of the tubing. Handle Bars of 0.74 m and Dia 38 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.26 m x 0.80 m x 1.59 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022-Supply and Fixng of Elliptical Cross Trainer: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.25 m is to be schedule HOT DIP Galvanized steel with a 114mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Foot rest of size 320 mm x 132 mm are attached to the Standing Bars 998 mm x 40 mm fabricated from 40 O.D. galvanized steel pipes. Lower part of Support Handrails of size 0.8 m high and Dia 47 mm and Upper part of Support Handrails of size 0.51 m high and Dia 32 mm fabricated from 47 mm O.D. and 32 mm O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.02 m x 0.53 m x 1.52 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications

Code No. SE-LAD Approved Rate - No.42/LAD/SE(OM)/AE(P)/OM/-24/2022-23 dt.20-05-2022 - Supply and Fixng of Bicycle: All products must tested and certified to meet EN16630 safety standards with GS test mark. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. The GS mark-EN 16630 certificates must be in the name of the supplier by themselves or through their authorised dealers or contractors. The EN16630 & GS Mark certificates must be submitted during the technical bid and the same must reflect clearly on the notified certifying bodies websites as online verification is mandatory during technical bid. All products must clearly display the GS mark as has been issued in the EN16630 safety certificates. Upright structural posts of height 1.31 m is to be schedule HOT DIP Galvanized steel with a 60 mm O.D. and 2.2mm (wall) thickness of the tubing. Two numbers of Pedal of size 113mm x 40mm & Rotating Disc of Dia 380 mm fabricated from 40 O.D. galvanized steel pipes. The poles are welded on to a base plate made from steel with 114mm inner diameter. Welded. Bearings : Maintenance-free ball bearings. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. The limiters must be in accordance with EN16630 safety norms. Scope of delivery : 1 completely pre- assembled equipment modules. Maintenance : Maintain according to EN16630 and the maintenance guide. EQUIPMENT DIMENSIONS: 1.11m x 0.51 m x 1.31 m with following standards 1. All products must be tested and certified to meet EN16630 safety standards with GS test marks. 2. The EN16630 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. 3. The GS mark EN16630 certificates must be in the name of supplier by themselves or through their authorized dealers or contractors. 4. These EN16630certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. 5. All Tubular steel of 2.5mm thickness are galvanized and zinc dipped 6. All Joints should be Robotic Welded. 7. All metal parts are powder coated using – Great Wall Powder (or equivalent) to the thickness of 80-120 microns. 8. Equipment which have sway and moving parts, must have built in safety limiters that prevent unwanted and excessive movement, which can cause injuries. 9. The limiters must be in accordance with EN16630 safety norms. 10. Seat(s) and footrest, if any – Shall be made of LDPE material and fixed to the main frame 11. Bolts, nuts, screws, washers and etc used for assembly shall be stainless steel 304 grade and shall be tamper resistant stainless steel. 12. Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as a safety feature against protruding hardware, aesthetic pleasing against ugly exposed hardware and prevention against vandalism as well. 13. All open ends of pipe to be closed with GI/LLDPE caps, base plate cover shall be made of virgin LLDPE plastic by rotational molding with minimum 8mm thickness, UV resistant and colour as approved by Engineer-in-Charge. 14. High quality grip rubber should be used on handles. 15. Foothold shall be fixed on ground with concrete 1:2:4 and J shaped welded bolts and installed as per manufacturer specifications.

CODE NO. NPSR Providing and Fixing of Reverse Osmosis System having a capacity of 50 litres per Hour