Department Of Local Administration Tender

Code No. 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No. 4.1.5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level-1:3:6 (1cement: 3 coarse sand : 6 graded stone aggregate 20mm nominal size)

Code No. 4.1.10 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Code No. 4.3.1 Centering and shuttering including strutting, propping etc. and removal of form work for foundations, footings, bases for columns.

Code No. 13.16.1 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand)

Code No. 15.2.1 Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead - nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Code No. 15.7.4 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead - in cement mortar

Code No. 31.161.1D (Addendum) Providing, laying and jointing UPVC pipes (Finolex / jain / Supreme / Truebore / Nandi) (0.6 Mpa) conforming to IS specification 4985 and ISI marked including transportation to the site, lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment, including cost of solvent cement, UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc., complete all as per IS and CPWD specification. - 75mm dia.

Code No. 4.12B.1 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layer by manual means in sub-base / base course on well prepared surface and compacting with smooth 3 wheeled steel roller to achieve the desired density.

Code No. 4.92C Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth 3 wheeld steel roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite Crushable type such as moorum or gravel for screening and gravel for binding to fill up the interstices of coarse aggregate, watering and compacting to the required density - by manual means - Water bound macadam Gr-II with moorum or gravel screening. (As per MoRTH specification, 4th Revision)

Code No. 6.1.MO Cleaning the existing W.B.M. road surface including removing of binding material and other foreign matter with wire brushes and small picks, sweeping with brooms or soft brushes sand finally dusting with old gunny bags and/ or compressed air to receive bituminous treatment. As per clause no 502.4.2 and 503.3.1 of MOST specification

Code No. 6.5F.1.MO Providing and applying tack coat on the prepared surface, heating bitumen in boiler and spraying the bitumen with spray set fitted on bitumen boiler-on granular base such as WBM and WMM surfaces not bitumen primed. Rate of application 10kg/10sqm

Code No. 6.11B.MO Providing and laying open graded premix Carpet 20mm thick on prepared surface in a single course as wearing course composed of specified size of stone aggregates premix with a bituminous binder in mini hot mix plant 6 to10 tonne laying manually and rolling with power roller 8 to10 tonne but excluding cost of primer / tack coat. As per clause no 509 of MOST specification

Code No. 6.17.MO Providing and applying premixed seal coat type `B' comprising of thin application of fine aggregate premix with bitumen binder in mini hot mix plant, carriage manually of mixed material and laying and rolling with power roller 8 to10 tonne. As per clause no 513 of MOST specification

Code No. 0322 (Baic rate Addendum) Hiring charges for front end loader JCB as direced by the Engineer-in-charge.

NPSR (SE approved rate) Fabrication, supply and fixing of Village / informatory name board of size 1.06mts x 0.61mts. The width of the board is tapered at 0.80mts upto 1.06mts to give the triangular shape at One end with High Intensity reflective sheeting of required color encapsulation on aluminum sheet of not less than 2mm thick suitably supported and framed with 25mm x 25mm x 3mm AISI 316 grade Stainless steel angle and the board frame is supported alround with AISI 316 grade stainless steel pipe of 38.10mm dia (outer dia & 2mm wall thickness). The Village names / street names, lettering and symbols will be provided by High Intensity grade white sheeting. The board is supported by Two Nos. of 63.5mm dia post S.S. pipes of 2.0mts. height with same dia Dummy plate arrangement at the top. The board frame and post pipes are welded by Tig welding with necessary polishing etc. and M.S. pipe of 50mm dia for a length of 35cm will be welded at the bottom of the posts and fixed in a ground pit of size 0.45 x 0.45 x 0.55 mts. with P.C.C 1:2:4. Rate including all the materials, S.S. welding, Grinding, Polishing, fabrication charges, Conveyance etc. except Earth work and PCC charges, complete.