Department Of Local Administration Tender

Code No.4.1.10: Providing and laying cement concrete in position cement concrete of specified grade excluding the cost of centerings and shuttering- All works upto plinth level 1:5:10 (1 cement :5 sand :10 graded stone aggregate 40mm nominal size).

Code No.5.1.2: Providing and laying in position specified grade of reinforced cement concrete excluding the coast of centering, shuttering, finishing and reinforcement -All work upto plinth level 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Code No.5.2.2: Reinforcd cement concrete work in walls (any thickness) including attaced pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutment, postsreinforced cement concrete excluding the coast of centering,shuttering,finishing and reinforcement -All work upto plinth level 1:1.5:3 (1 cement: 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Code No.5.3: Reinforced cement concrete work in beams, suspended floors , roofs having slope up to 15degree landings , balconies , shelves , chajjas , lintels , bands , plain window sills , staircases and spiral stair cases upto floor five level excluing the cost of centering ,shuttering, finishing and reinforcement , with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No.5.9.1: Centering and shuttering including strutting and proping etc. and removal of form for foundation footings, bases of columns, etc. for mass concrete.-using steel sheet with M.S frames

Code No.5.9.5: Centering and shuttering including strutting propping etc and removal of form for -Lintels, beams, plinth beams, girders, bressummers ad cantilever.Using steel sheet with M.S frames

Code No.5.9.6: Centering and shutterng including strutting, propping etc. and removal of form for columns, pillars, piers, abutments, posts and struts.-Using steel sheet with M.S frames

Code No.5.12: Providing hoisting and fixing upto floor five level precast reinforced cement concrete in string courses, bands, copings, bed plates, anchor blocks, plain window sill and the like including the cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1cement: 3sand) on exposed surfaces complete, but excluding the cost of reinforcement with 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggreagate 20mm nominal size).

Code No.5.18.2: Providing precast cement concrete jali 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centering and shuttering, roughening cleaning , fixing and finishing in cement mortar 1:3 ( 1 cement : 3 fine sand) etc. complete excluding plastering of the jambs, sills and soffits - 40 mm thick

Code No.5.22.6: Steel reinforcement for R.C.C.work including straightening , cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars (TISCON / VIZAG / IISCO / SAIL / JSW) Fe - 415 or more

Code No.6.1.1: Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 coarse sand)

Code No.6.1.2: Brick work with common burnt clay F.P.S. (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:6 (1cement: 6 sand).

Code No.6.4.2: Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:6 ( 1 cement : 6 coarse sand)

Code No.6.13.1: Half brick masonry with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in superstructure above plinth level upto floor five level - cement mortar 1:3 (1cement: 3 coarse sand).

Code No.6.15: Extra for providing and placing in position 2 nos 6mm dia M.S.bars at every third course of half brick masonry

Code No.10.25.2: Steel work welded in built up sections /framed work , including cutting,hoisting,fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Code No.9.118.1: Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Code No.10.16.2: Steel work in built up tubular (round,square or rectanglar hollow tubes etc.) trusses etc., including cutting , hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete - hot finished seamless type tubes

Code No.11.3.1: Cement concrete flooring 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc .complete - 40mm thick with 20mm nominal size stone aggregate

Code No.11.36A: Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :15622 (thickness to be specified by the manufacture of approved make ( Jhonson/Asian/ Somany/Nitco) in all colours, shades of sizes of size 200x300 mm as approved by Engineer -in -charge in skirting,risers of steps and dados over 12mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm. Including pointing in white cement mixed with pigment of matching shade complete -size 200x300mm.

Code No.11.38.1: Providing and laying ceramic glazed floorl tiles 300x300 (thickness to be specified by the manufacturer ) of first quality conforming to IS :15622 of approved brand make (Bell/ Jhonson/Regency/ Somany/Naveen/Asian)) in all colours, shades except white , ivory, grey, fume red brown laid on 20mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) . Including pointing in white cement mixed with pigment of matching pigments complete.

Code No.12.50: Providing & fixing precoated galvanised iron profile sheets (size, shape, and pitch of corrugation as 0.50mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired. The sheet shall be fixed using self drilling / self tapping screws of size (5.5 x 55 mm) with EPDM seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins , rafters and trusses and including cutting to size and shape wherever required

Code No.13.8.3: 12mm thick cement plaster of mix :Cement mortar 1:5 ( 1 cement : 5 fine sand)

Code No.13.9.2A: 15 mm cement plaster on the rough side of single or half brick wall of mix 1:5 (1cement : 5 fine sand)

Code No.13.9.2: cement plaster 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement - 20mm cement plaster

Code No.13.46.1: Finishing walls with acrylic smooth exterior paint of required shade - New work (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg / 10 sqm

Code No.13.61.1: Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or more coats on new work.

Code No.16.94: Supplying fixing and commissioning of suguna /Texmo/Sharp 0.5 HP mono block pump set slow speed single phase motor . The rate include the cost of pumset ,pupset fixing in position and test run etc.complete

Code No.17.13.2: Providing and fixing white vitreous china water closet squatting pan (indian type ) Orissa pattern WC pan of size 580 x 440mm.

Code No.17.14.1: Extra for using coloured WC pan instead of white WC pan Orissa pattern WC pan 580x 440mm.

Code No.31.161.1F: Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.60 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends,tees, threaded pieces,couplers,reducer,endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Code No.31.164.1L: Providing and fixing in position UPVC moulded equal Tee (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete -110mm dia

Code No.31.171.1I: Providing and fixing in position UPVC moulded endcap (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110mm dia

Code No.31.178.1D: Providing and fixing in position UPVC fabricated bend (Finolex / jain)(0.6 Mpa) conforming to IS 7834 part II and ISI marked,including labour charges for jointing, jointing materials etc,complete - 110 mm dia

Code No.18.8.2: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings , with one step CPVC solvement cement and the cost of cutting chases and making good the same including testing of joints complete - Concealed work , including cutting chases and making good the wall etc - 20 mm nominal outer dia pipes

Code No.18.9.3: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete - external work - 25mm nominal outer dia pipes

Code No.18.8.3: Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings , with one step CPVC solvement cement and the cost of cutting chases and making good the same including testing of joints complete - Concealed work , including cutting chases and making good the wall etc - 25 mm nominal outer dia pipes

Code No.18.7.5: Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete - internal work - exposed on wall -40mm nominal outer dia pipes

Code No.18.15.2: Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) -25mm nominal bore

Code No.18.17.1: Providing and fixing gun metal gate valve with CI wheel of approved quality (screwed end) -25mm nominal bore

Code No.18.17.3: Providing and fixing gun metal gate valve with C.I.wheel of approved quality (Screwed end) - 40mm nominal bore

Code No.18.18.3: Providing and fixing ball valve (brass) of approved quality , high or low pressure , with plastic floats complete - 25mm nominal bore

Code No.18.48A: Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI: 12701 marked , with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank - Circular Tank

Code No.19.18.1: Supplying and fixing CI cover without frame for man holes 455x610mm rectangular CI cover (light duty) the weight of the cover to be not less than 23 kg

Code No.19.30.1.1: Constructing brick masontry chamber for underground CI inspection chamber and bends with 75 class designation bricks in cement mortar 1:4 ( 1 cement :4 coarse sand ) CI cover with frame ( light duty) 455x610mm internal dimensions, total weight of cover with frame to be not less than 38kg (weight of cover 23 kg and weight frames 15 kg) R.C.C. top slab with 1:2:4 mix ( 1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) foundation concrete 1:5:10 ( 1cement: 5 fine sand : 10 graded stone aggregate 40mm nominal size ) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on wall and bed concrete etc. complete as per standard design inside dimensions 455 x 610mm and 45cm deep for pipe line with three or more inlets with F.P.S. bricks. (non modular) bricks of class designation 7.5

Code No.19.33: Constructing soak pit 1.20x1.20x1.20m filled with brick bats including SW drain pipe 100 mm diameter and 1.20m long complete as per standard design.

Code No.12.43.2: Providing and fixing unplasticised - PVC pipe clips of approved design to unplasticised- PVC rain water pipes by means of 50x50x50mm hard wood plugs , screwed with M.S. screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc., complete - 110mm