Works Department Tender

Providing and laying Granular Sub-base with grading IV stone screening materials as per approved drawing and technical specifications as per Section 900 and Clause 401 of MoRT&H Specifications for Road & Bridge works (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing & applying tack coat with Bitumen Emulsion(rapid setting) on prepared surface including cleaning of road surface and spraying primer @ 0.20 Kg. / Sqm. using mechanical means as per Clause No.503 and Section 900 of MORT&H Specifications for Road & Bridge works (5th Revision) complete in all respect & as per direction of the Engineer-in-Charge.

Providing and laying compacted Semi Dense Bituminous Concrete (Grading-II) using 60/70 grade Bitumen and crusher broken hard granite aggregates of specified grading, premixed with bituminous binder @ 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per clause No.501, 508 and section 900 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (4th Revision) & including cost of all materials, labour, T&P,royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing dry lean cement concrete sub-base over a prepared sub-grade with coarse and fine aggregates conforming to I:S 383, the size of coarse aggregate not exceeding 25mm , aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 Kg/Cum, optimum moisture content to be determined during trial length construction, concrete strength not be less than 10Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver and compacting with vibratory roller, finishing and curing as per approved drawing and specification as per Clause No.601 of MoRT&H Specifications for Road and Bridge works (5th Revision) including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing un-reinforced dowel jointed plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400kg/cum, coarse and fine aggregates conforming to I:S 383, maximum size of coarse aggregate not exceeding 25mm, mixed in batching and mixing plant as per approved mixed design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrance, seleant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per approved drawing and technical specification as per Clause No.602 of MoRT&H Specifications for Road and Bridge works (5th Revision) including cost and conveyance of all materials and as per direction of Engineer-in-Charge

Providing and fixing of retro-reflectorised direction and place identification sign as per IRC:67 made of high intensity grade sheeting vide Clause No. 801.3 of specifications for road and bridge works of Ministry of Road Transport & Highways (5th Revision) fixed over aluminium sheeting, 2mm thick with area not exceeding 0.9 Sqm supported on a mild steel angle iron post 75mm x 75mm x 6mm , firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Directional/Place Identification sign (1800x1200)

Directional/Place Identification sign (1200x700)

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide Clause No. 801.3 of specifications for road and bridge works of Ministry of Road Transport & Highways (5th Revision) fixed over aluminium sheeting, 1.5mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm , firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Facility information 800mm x 600mm rectangular

Route Marker signs ( 450 x 600 mm)

Cautionary Signs (900 mm equal trangular)

Mandatory signs (Circular Signs 600 mm)

Providing and laying Plain cement concrete of grade M-20 in foundation as per drawing and technical specification using High Strength approved quality Cement and coarse granite aggregate conforming to Table 1000-1 with formwork as per Section 900,1000,1500,1700, 2100 & 2200 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing and laying Reinforced cement concrete of grade M-20 in Sub Structure/Drain wall as per drawing and technical specification using High Strength approved quality Cement and coarse granite aggregate conforming to Table 1000-1 with formwork, centering and shuttering as per Section 900,1000,1500,1700 & 2200 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing and laying Plain cement concrete (1:3:6) in foundation in Drain etc.complete as per drawing and technical specification using High Strength approved quality Cement and black hard granite stone crushed metal of 40mm nominal size with formwork as per Section 900,1000,1700 & 2100 of specifications for road and bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Straightening cutting, bending bent up or coiled rods, including cranking, hooking, welding or jointing the M.S. rods or tor steel of primary steel producers such as SAIL / Tiscon / RINL / JINDAL STEEL / SHYAM STEEL (Grade Fe-500D) confirming to I.S. 432 (Plain) and 1785 (Tor) steel and binding, tying the grills, hoisting, lowering and placing in proper position required for R.C.C. works including cost, conveyance of M.S. rods or tor steel and binding wires of 18 to 20 gauge and cost of all labour with all T&P required for the work etc. complete as directed by the Engineer- in-Charge.

Providing Road marking with Hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @250 grams per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC-35 and as per Clause No.803 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge.

Providing, fitting and fixing salitex board expansion joint for finished item of work as per section 900, 2600 of MORT&H Specifications for Road & Bridge works (5th Revision) and direction of the Engineer-in-Charge.

Providing ,laying factory made 80 mm thick cement concrete interlocking paver blocks of M - 30 grade made by block making machine with strong vibratory compaction of approved size and shape laid over 50mm thick compacted bed of course sand layer including filling sand in the interstics/ joints, including cost conveyance of all materials, labour, and (T&P) required for the work etc complete and as per direction of Engineer in charge.