Works Department Tender

Providing and laying surface dressing as wearing course in single coat using crushed stone aggregates of specified size on a layer of bituminous binder of 60/70 penetration grade of bitumen laid onprepared surface and rolling with 8-10 tonne smooth wheeled steel roller as per Clause 510 of MoSRT&H Specifications for Road & Bridge works (4th Revision)

Providing & applying primer coat with Bitumen emulsion on prepaired sueface of granular base including cleaning the road surface and spraying primer @ 0.60kg / sqm using mechanical means as per clause 502 of MoSRT & H specification for road & bridge works etc complete as per direction of EIC..

Providing & applying tack coat with Bitumen emulsion using emulsion pressere distributer @0.20kg / sqm on the prepared bituminous / granular suerface cleaned with mechanical broom as per clause 503 of MoSRT & H specification for road & bridge works.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness using 0.27cum of 13.2 mm to 5.6 mm aggregates using S-60/70 penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type C as per Technical Specification Clause 508 of MoRD including cost, lead, lift royality and taxes of all materials required for the work by manual means etc. complete and as per direction of the Engineer -in- charge.

Providing 6 mm thick pre coated seal coating including cost, conveyance, royalty & taxes of all materials including hire & running charges of P.R .R etc complete

Construction of enbankment with approved material obtained from borrow pit with lead and lift transporting to site by mechanical means within lead of 5kms, spreading grading to required slope and compacting to meet requirement of table 300-2 and clause 305 of MoSRT&H specification for road and bridge works etc complete as per direction of EIC.

Earthwork in hard soil for drain cutting etc complete as per the direction of the EIC

Finishing Wall with Water Proofing Cement paint Two coat over a coat of cement wash of approved shade on new work including all cost of cement paint etc, Complete.

Providing and fixing of typical informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause Annexure 300,800,1700 of MORD as per direction of the Engineer in charge

Providing, fitting, fixing & writting of Km stone, 200mtr stone & cautinary sign board etc all complete as per direction of EIC. KM Stone

Providing, fitting, fixing & writting of Km stone, 200mtr stone & cautinary sign board etc all complete as per direction of EIC. 200 mtr Stone

Providing, fitting, fixing & writting of Km stone, 200mtr stone & cautinary sign board etc all complete as per direction of EIC. Cautionary sign board

Providing, fitting, fixing & writting of Km stone, 200mtr stone & cautinary sign board etc all complete as per direction of EIC. Guard Post