Works Department Tender

Painting two coats with plastic emulsion paint over a coat of water bond cement primer to make an even finished surface in all floors and heights to wall surface of approved make and shade including cost, conveyance of all materials, cost of all labour,labour cess, T&P etc. complete as per the direction of the Engineer-in-charge.

Ground Floor

First Floor

4cm thick grading concrete (1:2:4) on roof slab with 12mm & down grade size black hard granite chips for old work with chicken wire mesh etc. complete including cost, conveyance, royalties and taxes of all materials with all labour, cess and T&P required for the work etc. complete in all respect. (G.F.)

Supplying and applying sikadur combiflex (200mm x 2mm) of sika product for joint and crack of expansion joints with sikadur 31c epoxy addessive over a cleaned free from oil, grease, surface including cost, conveyance of all materials and labours, T&P all labour etc. complete for direction of Engineer-in-charge.

Supply & installation of wall paneling of Anutone slats surco high density fiberboard made out of pure pinewood particles , Fire Resistance - Pink in colour core with Fire Resistance BS 476 part 5 , BS 476 part 6 , BS 476 part 7 ISO 1182 ASTM E662 Smoke Density - Melamine laminated finish, perforated wooden grooved HDF slats L16-2 (2 mm grooves @ 8 mm centers),tongue-groove edge for a seamless look of lineal dimension size 128 mm x 2440 mm x 16 mm thick having density 700 Kg /m3, weight -9 Kgs/m2 with back fleecs from soundtex Germany nonwoven acoustic to be pasted on slats surco is to be installed by using GI strut system. The technical parameters are as follows Core Variants - Fiberboard, Climate (OC RH) – 50, 70 Light reflectance – 75%,Green (RC %) – 25, Hygiene (VoC, Clean room) – Low, Class 1,Strength, Load capacity (Kg) - Anti sag, Ball-Impact. The concealed wall paneling system shall include GI Wall channel (WC25) having thickness 0.45mm, length 3600mm, unequal flanges of 15 & 20mm and web of 25mm should be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then fixed Main channels (MC45) having thickness 0.9mm, length 3600mm, equal flanges of 15mm and web 45mm from the side wall & fixed at every 1200mm centers with GI cross channel(CC25) having thickness 0.45mm, length 3600mm, knurled web 35mm, depth of 25mm and equal flanges 9.5mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600mm centers. The framework will maintain 50 / 75 mm gap from the walls. Now clad the wooden slats surco on the CC 18 with the help of center & edge clips to get better locking of slats. The tongue & groove are to be properly aligned to get flush look . Synth poly fiber PF 5 x 50 wool of 500 gsm to be filled between the horizontal & vertical studs as in filler with the help of wire / stick 7 adhesive. Test certificate of the use products shall be submitted after procurement of materials

Supplying, fitting and fixing of grid mineral fibre ceiling board having size 600x 600mmx16mm of approved design and quality complete with frame and all fitting and fixtures including cost, conveyance of all materials and labours, T&P all labour etc. complete for direction of Engineer-in-charge.

Providing and painting with two coats of Weather Coat of approved quality, make and shade to give an even surface including the cost of all materials, labour, conveyance, taxes, loading, unloading, scaffolding, T&P, etc. all complete as per the direction of Engineer-in-charge. (F.F.)

Supply and fixing of Un-plasticised Poly Vinyl Chloride (UPVC) sliding windows of FENESTA / NCL or equivalent three track - only two glass shutters sliding duly manufactured using UPVC reinforced profiles of 108mm x 45mm x 2.5mm or equivalent for outer frames, 58mm x 39mm x 2.5mm or equivalent for sliding shutter frames capable of mounting single glazing system, structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 1.5mm prefabricated & welded through fusion welding the window sash shall be fitted with 6mm thick clear toughened glass of SAINT-GOBAIN or reputed make duly fixed with EPDM weathering seal resistant accessories like clipping locking system made of aluminium 1 no., per set of sashes and the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing / deglazing at site with 10 years manufactures warranty for discoloration, wraping, mechanical failures, shrinkages, rotting, corrosion etc. with a quality certificate from relevant department of Govt. of India, including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site with templates for casement sizing complete for finished item of work (structural requirements profiles are to be got approved by the Engineer-in-Charge of the work before fabrication of the shutter) as per specification and direction of the Engineer-in-Charge.

Supply and fixing of Un-plasticised Poly Vinyl Chloride (UPVC) FENESTA / NCL or equivalent Casement door -60 series duly manufactured using UPVC reinforced profiles of 60mm x 50mm x 2.5mm for outer frames, 102mm x 60mm x 2.25mm for casement Door sash profile and 74mm x 60mm x 2.25mm for millon profile capable of mounting single slazing system , structurally reinforced with hot dip galvanized up to 50 microns of minimum thickness of 2.0mm prefabricated & welded through fusion welding the door sash shall be fitted with 12mm thick clear WPC board of green plymake duly fixed with EPDM weathered seal resistance accessories like clipping lock system made up aluminium1 noper set of sashesand the system is to be installed at the site using anchor fasteners, silicon rubber sealant, easy glazing / deglazing at site with 10 years manufactures warranty for discoloration, wraping, mechanical failures, shrinkages, rotting, corrosion etc. with a quality certificate from relevant department of Govt. of India, including cost and conveyance of all materials, accessories, labour charges for transportation, erection at site with templates for casement sizing complete for finished item of work (confrming ASTM D638-14,EN-477-95) (structural requirements profiles are to be got approved by the Engineer-in-Charge of the work before fabrication of the shutter) as per specification and direction of the Engineer-in-Charge.,

Providing and Painting two coats of synthetic enamel paint of approved quality, make and shade on Iron / Wood Works over one coat of primer including the cost of sand papering, surface polishing, cost of all materials, cost of labour, conveyance, taxes, loading, unloading, scaffolding, T&P, etc. as per direction of Engineer-in-charge.

Ground Floor

First Floor

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @ 0.90 mtr. C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc with cost, conveyance, taxes of all materials, labour, T&P etc.as per the direction of Engineer-in-Charge.

Supplying, fabricating and fixing of structural steel work using GI sections such as GI angle, flat, channel, square bar, plate, etc. including cutting, bending, welding, hoisting and fixing in position including cost, conveyance,taxes of materials, laboutr, T&P, etc. complete.

Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Earth work in excavation of foundation in all kinds of soil including moorum, stony earth mixed with boulders (except sheet rocks and boulders requiring blasting) with all leads and lifts including dressing and leveling the bed and depositing the excavated earth at places away from work site with all leads and lifts including cost of all labour and T&P and dewatering if required for the works etc. complete as directed by the Engineer-in-charge.

Supplying, filling in foundation and plinth with sand well including watered and rammed with cost, conveyance, royalties and taxes of sand with labour and T&P required for the work etc. complete.

Cement concrete of proportion (1:3:6) in foundation and floors using 4cm (1 ½”) size clean hard black crusher broken granite stone metal of approved quality and from approved quarry including hoisting, lowering and laying concrete in layers not exceeding 15 cm. (6”) thick to the required level ramming, watering, curing etc. complete including cost, conveyance, royalties and taxes of all materials with all labour, cess and T&P required for the work etc. complete in all respect.

Plain cement concrete (1:2:4) using 12mm size black hard crusher broken granite chips of approved quality from approved quarry including hoisting, lowering and laying concrete in layers, watering, curing etc. complete including cost, conveyance, royalties and taxes of all materials with labour, cess and T&P etc. required for the work complete.

R.C.C.M-20 Grade in work using 40mm to 10mm size crushed stone aggregates mixed by concrete mixer, laying in layers and compacting by vibrator & all leads and lifts including frame works etc as per approved Drawing & Technical Specifications.

Drain Bed

Side Wall

Pre cast slab

Straightening bent up or coiled M.S. rod or HYSD steel (Fe-500/fe-415), cutting, bending, cranking, hooking, welding or jointing (if required), the M.S. rod or HYSD steel and binding, tying the grills, hoisting, lowering and placing in proper position as required for R.C.C. works including cost, conveyance and M.S. rod or HYSD steel and binding wires of 18 to 20 gauge and labour with all T&P required for the work etc. complete in all floors (weight of binding wire will not be considered for payment and payment will bhe made on weight of M.S. Road or HYSDD steel only. Steel bar of only manufactureing companies such as S.A.I.L. of Fe- 415/Fe-500 grade are to be used in the work & if required original bill of S.A.I.L. steel has to be produced by the Contractor)