Works Department Tender
Search from a pool of business opportunities related to Odisha tenders on the online platform of BidAssist. Be it an Odisha PWD tender or a civil aviation tender, one can find every tender Odisha government, as well as PSUs and other organizations, post online. Every tender, active or achieved, is sourced from the eProcurement Odisha website and thus carries full credibility.
Costs
EMD
₹ 6,28,800Document Cost
₹ 10,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_EICCL_106956_3Tender No
CCE, SC-(RandB)-BAM-10/2024-25Tender Authority
Works Department ViewPurchaser Address
-Website
http://https://www.worksodisha.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
50mm thick
20
141
2834.2
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
230
200
46020.7
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
100
5
570
Bar Above 12mm dia:-
100
11
1140
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
230
627
144394
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
230
424
97648.8
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
7.4
1757
13008.53
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
6.75
13359
90173.32
Approach Slab
16.91
7114
120312.11
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
35.1
8692
305123.6
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
28.8
14192
408737.38
Providing and fixing steel structure arrangement for replacing the bearings of bridge as required with Cost of scaffolding and staging or temporary steel structure for entire work of this bridge.
4
60726
242905.2
Lifting of span for replacement of bearing . Lifting of span i.e. superstructure structure of bridge for repalcement of old bearings and including all hire and running expenses of plants hydraulic jacj, power jack, generator set , welding machine, and equipment& span length 30 mts each side
2
385710
771421.84
Providing and Fixing of Elastomeric bearing assembly consisting of 7 layers of elastomer bonded to 6 nos Internal reinforcing steel laminates by the process of vulcanisation conforming to IS-83 (Part-III)/2015 in suspended span as well as on Piers in all respect etc. complete.
145800
-
67068
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
12
1036
12443.16
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
12
282
3384
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
546
319
174523.44
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
1000
8
8270
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
23
638
14674.69
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
210
1058
222274.5
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
25
171
4289
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
25
448
11220
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
20
710
14210.4
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
135
278
37615.05
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
150
2142
321435
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
150
337
50583
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5682
11364.58
Repair and Strengthening work for H L Bridge over Kushmi Nallah at Ch. 11.076Km in the Balipadara -Karasingi Road (from 0.0 to 32.600).
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
295.5
209
61812.69
50mm thick
50
141
7085.5
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
345.5
218
75491.75
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
1000
5
5700
Bar Above 12mm dia:-
1500
11
17100
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
345.5
627
216904.9
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
345.5
424
146685.48
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
9.95
1757
17491.2
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
4.95
13420
66430.73
Approach Slab
43.6
7176
312881.88
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
53.6
8692
465943.73
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
64
14192
908305.28
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
24
1036
24886.32
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
24
282
6768
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
740
319
236533.6
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
600
8
4962
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
35
638
22331.05
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
295.5
1065
314949.81
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
50
722
36117
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
19.8
278
5516.87
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
66
2099
138571.62
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
220
338
74496.4
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5687
11375.28
Repair and Strengthening work for Minor Bridge over Jamuna Nallah at 18.200 Km in Budhamba - Buguda road (from 16/000 to 26/000 km).
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
244
209
51039.92
50mm thick
20
141
2834.2
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
264
218
57684
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
100
5
570
Bar Above 12mm dia:-
200
11
2280
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
264
627
165739.2
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
264
424
112083.84
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
5.6
1757
9844.3
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
4.5
13420
60391.58
Approach Slab
36.8
7176
264083.79
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
23
8692
199938.54
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
16
14192
227076.32
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
12
1036
12443.16
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
12
282
3384
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
170
319
54338.8
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
300
8
2481
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
25
638
15950.75
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
244
1065
260060.08
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
20
171
3431.2
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
20
448
8976
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
20
722
14446.8
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
4.5
278
1253.84
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
30
2099
62987.1
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
100
338
33862
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5687
11375.28
Repair and Strengthening work of Bridge over Baghua river at 20.515 Km in Budhamba - Buguda road (MDR-72)
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
584
209
122161.12
50mm thick
50
141
7085.5
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
634
218
138529
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
1000
5
5700
Bar Above 12mm dia:-
2000
11
22800
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
634
627
398025.2
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
634
424
269171.04
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
24.5
1757
43068.8
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
22.5
13338
300115.13
Approach Slab
18.8
7094
133372.65
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
62.3
8692
541572.65
Dismantling the existing strip seal expansion joint i/c structrual steel edge beam anchor plate etc. of the existing damaged expansion joint by cutting with gas cutter and breaking of concrete by machanical means i/c disposal of rubbish &malba etc. complete as per the direction of the Engineer-in-Charge.
16
2793
44694.56
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
16
14192
227076.32
Providing and fixing steel structure arrangement for replacing the bearings of bridge as required with Cost of scaffolding and staging or temporary steel structure for entire work of this bridge.
1
60726
60726.3
Lifting of spans i.e. super structure of bridge for replacement of old bearings, including hire and running expenses of all plants, Hydraulic jacks, Power packs, Generator sets, welding machines and equipments for span length about 30 m. both ends.- 2 spans
4
385710
1542843.68
Providing and fixing in position and level Elastomeric bearings of size 450 mm x 450 x 60 mm thick confirming to IRC:83 (Part-II) complete with all respect and as per drawing/as directed by Engineer-in-charge. NOTE:-Final size of bearing will be as per draing, in the BOQ size of bearing taken for estimate purpose it may vary accordingly.
291600
-
134136
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
32
1036
33181.76
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
32
282
9024
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
2131.38
319
681274.3
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
1050
8
8683.5
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
60
638
38281.8
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
584
1065
622438.88
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
200
171
34312
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
200
448
89760
Drilling suitable holes in reinforced or plain concrete with power driven drill machine to a minimum depth of 100 mm to 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-in-charge.
-
-
-
Upto and including 12mm dia
200
81
16332
Upto and including 16mm dia
100
137
13718
Upto and including 20mm dia
100
161
16182
Providing and placing high strength, non shrink pre-packed free flow micro concrete having compressive strength of 60 MPa at 28 days (compresssive strength of one day should not be less than 25 MPa) as per specifications. The micro concree mix shall be prepared by mixing non shrink pre-packed free flow micro concrete powder with well graded cleaned crushed, aggregate 10mm & down (aggregate should be less than 10mm but retained on 3.36mm) in proportion of 2:1 (Two part prepack micro concrete powder : one part stone aggregate) by weight for repairing excessively damaged area of structural elements excluding reinforcement but including scaffolding, curing inclusive of all labour, materials, equipment etc. complete as per specifications and instructions of Engineer-in-Charge. (NSI)
7.5
30200
226502.48
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
50
722
36117
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
40.5
278
11284.52
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
160
336
53761.6
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
300
2008
602571
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5677
11355.3
Strengthening structural elements with non-metallic composite fiber wrapping system comprise of uni-directional glass fiber sheet and compatible saturant. Grinding/ moulding concrete substrate, cleaning it with wire brush removing oil, laitance if present, rounding sharp edges to min 25 mm radius etc. complete. Applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixo-tropic putty etc. complete. Wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc. repeat the same procedure for multiple layer with the interval of 8hrs.Applying second coat of saturant after min. 12hrs, rectify air voids if any paste the river sand on it to make surface rough to take any further finishes Sand pasting: Applying second coat of saturant after min. 12 hrs, rectify air voids if any paste the river sand on it to make surface rough to take any further finishes (Mode of measurement: Per sq.mt of glass fiber sheet consumed and not surface area of application)
90
5226
470407.5
Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50x55 system spreading fibers in star pattern including application of saturant, etc complete.
192
500
96000
Repair and Strengthening work for Minor Bridge over Kusumi Nalla at ch 14/404 km on 6th km of AKO road to Polosara via subalya (ODR)
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
181
209
37861.58
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
181
225
40757.58
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
50
5
285
Bar Above 12mm dia:-
200
11
2280
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
181
627
113631.8
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
181
424
76845.36
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
1
1757
1757.91
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
17.89
7085
126755.66
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
17
14192
241268.59
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
19.89
8692
172903.37
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
4
1036
4147.72
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
5
278
1393.15
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
4
282
1128
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
235
319
75115.4
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
5000
8
41350
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
181
1068
193396.69
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
25
171
4289
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
25
448
11220
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
100
335
33571
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5676
11353.1
Repair and Strengthening work for Nasakhai Nallha Bridge on Bhanjanagar Tillisingi Tarasingi Daspalla road at 37.600 KM
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
151
209
31586.18
50mm thick
50
141
7085.5
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
201
217
43639.11
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
500
5
2850
Bar Above 12mm dia:-
500
11
5700
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
201
627
126187.8
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
201
424
85336.56
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
76.71
1757
134849.28
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
104.43
7303
762738.97
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
147.77
8692
1284561.65
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
27
14192
383191.29
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
8
1036
8295.44
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
8
282
2256
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
724.92
319
231713.43
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3580
8
29606.6
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
92
638
58698.76
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
151
1065
160854.26
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
50
721
36072.5
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
314.72
1339
421655.56
Providing and laying bituminous concrete with batch type hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site laying with a hydrostatic paver finisher with sensor control to the required grade, level and allignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compactionas per Claue 509 of MoSRT&H Specification for Road & Bridge works ( 5th Revision ) etc. complete and as per directions of Engineer-in-Charge.
12.59
10130
127541.61
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
12.65
278
3524.67
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
314.72
904
284579.27
Repair and Strengthening work for Bridge over Boda Nadi on Nayagarh-Jagannathprasad Bhanjanagar road at 55.085 Km
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
558
209
116722.44
50mm thick
121
141
17146.91
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
679
209
142060.38
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
1000
5
5700
Bar Above 12mm dia:-
2500
11
28500
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
679
627
426276.2
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
679
424
288276.24
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
31.8
1757
55901.54
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
36
13194
475011.72
Approach Slab
19.8
6950
137622.08
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
70.8
8692
615462.98
Dismantling the existing strip seal expansion joint i/c structrual steel edge beam anchor plate etc. of the existing damaged expansion joint by cutting with gas cutter and breaking of concrete by machanical means i/c disposal of rubbish &malba etc. complete as per the direction of the Engineer-in-Charge.
40
2793
111736.4
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
40
14192
567690.8
Providing and fixing steel structure arrangement for replacing the bearings of bridge as required with Cost of scaffolding and staging or temporary steel structure for entire work of this bridge.
4
60726
242905.2
Providing and Fixing of Elastomeric bearing assembly consisting of 7 layers of elastomer bonded to 6 nos Internal reinforcing steel laminates by the process of vulcanisation conforming to IS-83 (Part-III)/2015 in suspended span as well as on Piers in all respect etc. complete.
291600
-
134136
Lifting of span for replacement of bearing . Lifting of span i.e. superstructure structure of bridge for repalcement of old bearings and including all hire and running expenses of plants hydraulic jacj, power jack, generator set , welding machine, and equipment& span length 30 mts each side
4
385710
1542843.68
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
32
1036
33181.76
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
32
282
9024
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
1958.98
319
626168.37
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3300
8
27291
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
80
638
51042.4
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
558
1062
592657.38
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
300
171
51468
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
300
448
134640
Drilling suitable holes in reinforced or plain concrete with power driven drill machine to a minimum depth of 100 mm to 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-in-charge.
-
-
-
Upto and including 12mm dia
200
81
16332
Upto and including 16mm dia
500
137
68590
Upto and including 20mm dia
200
161
32364
Providing and placing high strength, non shrink pre-packed free flow micro concrete having compressive strength of 60 MPa at 28 days (compresssive strength of one day should not be less than 25 MPa) as per specifications. The micro concree mix shall be prepared by mixing non shrink pre-packed free flow micro concrete powder with well graded cleaned crushed, aggregate 10mm & down (aggregate should be less than 10mm but retained on 3.36mm) in proportion of 2:1 (Two part prepack micro concrete powder : one part stone aggregate) by weight for repairing excessively damaged area of structural elements excluding reinforcement but including scaffolding, curing inclusive of all labour, materials, equipment etc. complete as per specifications and instructions of Engineer-in-Charge.
7.5
30172
226290.23
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
121
716
86681.98
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
36
278
10030.68
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
200
331
66282
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
60
1895
113721
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
4
5660
22640.48
Strengthening structural elements with non-metallic composite fiber wrapping system comprise of uni-directional glass fiber sheet and compatible saturant. Grinding/ moulding concrete substrate, cleaning it with wire brush removing oil, laitance if present, rounding sharp edges to min 25 mm radius etc. complete. Applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixo-tropic putty etc. complete. Wrapping the fiber sheet to structural element at desired orientation using tamping roller to avoid any air voids etc. repeat the same procedure for multiple layer with the interval of 8hrs.Applying second coat of saturant after min. 12hrs, rectify air voids if any paste the river sand on it to make surface rough to take any further finishes Sand pasting: Applying second coat of saturant after min. 12 hrs, rectify air voids if any paste the river sand on it to make surface rough to take any further finishes (Mode of measurement: Per sq.mt of glass fiber sheet consumed and not surface area of application)
90
5226
470407.5
Providing and fixing carbon fiber anchor including drilling hole in the base concrete, fixing the anchor using epoxy 50x55 system spreading fibers in star pattern including application of saturant, etc complete.
192
500
96000
Providing & Applying Pre- stressed carbon fiber laminates (1.2 mm thick and 100 mm wide) with compatible structural adhesive including. Grinding concrete substrate, cleaning it with wire brush removing oil, laitance if present, etc. complete. Applying compatible primer on prepared substrate, Filling the holes and uneven surface with thixo-tropic putty etc. complete. Marking the application area on structural element, cutting the plate to require size, applying compatible structural adhesive on plate in parabolic manner by adhesive laminating machine, paste the laminate on desire area by using tamping roller to avoid any air voids etc. complete. Applying second coat of saturant after min. 12hrs, rectify air voids if any paste the river sand on it to make surface rough to take any further finishes . (Mode of measurement: Per running Mt.)(NSI)
60
6707
402460.2
Providing and fixing end anchor including drilling hole in the base concrete, fixing the anchor using epoxy and fix the plate with fatner as required as per drawing/Engineer-In-Charge complete work.(NSI)
24
2000
48000
Repair and Strengthening work for Bridge over Boda Nadi on Pantiama- Chamunda- B D Pur Road at Chainage 14.90 Km
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
20
209
4183.6
50mm thick
40
141
5668.4
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
60
192
11527.2
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
50
5
285
Bar Above 12mm dia:-
100
11
1140
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
60
627
37668
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
60
424
25473.6
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
36.48
1757
64128.56
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
41.85
13146
550163.45
Approach Slab
18.75
6901
129411
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
18.75
8692
162993.38
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
32
14192
454152.64
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
41.85
278
11660.67
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
24
1036
24886.32
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
24
282
6768
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
1317.5
319
421125.7
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
2720
8
22494.4
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
42
638
26797.26
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
20
1055
21105.4
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
470
171
80633.2
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
470
448
210936
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
40
705
28216
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
697.5
1327
926231.18
Providing and laying bituminous concrete with batch type hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site laying with a hydrostatic paver finisher with sensor control to the required grade, level and allignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compactionas per Claue 509 of MoSRT&H Specification for Road & Bridge works ( 5th Revision ) etc. complete and as per directions of Engineer-in-Charge.
27.9
10068
280899.99
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5654
11308.36
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
60
329
19791
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
18
1926
34680.96
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
697.5
904
630700.43
Repair and Strengthening work for H L Bridge Over River Boda on Khallikote Boirani Aska Balipadar road at 81.780
-
-
-
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
47.25
278
13165.27
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
24
1036
24886.32
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
40
282
11280
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
2500.5
319
799259.82
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
1560
8
12901.2
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
1176
1328
1562198.4
Providing and laying bituminous concrete with batch type hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site laying with a hydrostatic paver finisher with sensor control to the required grade, level and allignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compactionas per Claue 509 of MoSRT&H Specification for Road & Bridge works ( 5th Revision ) etc. complete and as per directions of Engineer-in-Charge.
47.04
10121
476097.48
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5651
11303.04
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
1176
904
1063374.48
Repair and Strengthening work for Pankal Nallha Minor Bridge on Bhanjanagar Tillisingi Tarasingi Daspalla road at 32.250 KM
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
105.32
209
22030.84
50mm thick
30
141
4251.3
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
135.32
211
28667.54
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
500
5
2850
Bar Above 12mm dia:-
500
11
5700
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
135.32
627
84953.9
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
135.32
424
57451.46
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
38.22
1757
67187.32
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
65.94
7220
476152.08
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
90.05
8692
782802.85
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision).
27
14192
383191.29
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
8
1036
8295.44
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
8
282
2256
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
396.56
319
126756.44
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3580
8
29606.6
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
50
638
31901.5
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
105.32
1063
111972.01
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
30
718
21542.1
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
127.4
1337
170419.16
Providing and laying bituminous concrete with batch type hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site laying with a hydrostatic paver finisher with sensor control to the required grade, level and allignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compactionas per Claue 509 of MoSRT&H Specification for Road & Bridge works ( 5th Revision ) etc. complete and as per directions of Engineer-in-Charge.
5.1
10130
51664.99
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
5.85
282
1649.7
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
127.4
904
115198.9
Repair and Strengthening work for Rudhapadar Nallha Bridge on Bhanjanagar Tillisingi Tarasingi Daspalla road at 41.600 KM
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
375.9
209
78630.76
50mm thick
50
141
7085.5
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
425.9
223
95265.31
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
500
5
2850
Bar Above 12mm dia:-
1500
11
17100
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
425.9
627
267380.02
Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.
425.9
424
180820.1
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
5
1757
8789.55
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
27.62
7380
203856.59
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
40.62
8692
353108.85
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
25
14192
354806.75
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
10
1036
10369.3
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
10
282
2820
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
535.84
319
171275.9
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3580
8
29606.6
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
10
638
6380.3
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
375.9
1067
401419.85
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
50
725
36283.5
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
235.2
1341
315509.04
Providing and laying bituminous concrete with batch type hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to site laying with a hydrostatic paver finisher with sensor control to the required grade, level and allignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compactionas per Claue 509 of MoSRT&H Specification for Road & Bridge works ( 5th Revision ) etc. complete and as per directions of Engineer-in-Charge.
9.41
10130
95326.97
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
9.45
278
2633.05
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
225
345
77663.25
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
50
2300
115048
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5712
11425.2
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
314.72
904
284579.27
Repair and Strengthening work for HL Bridge over Baghua at ch 44/991km on KABABB road (SH-30)
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
400
209
83672
50mm thick
75
141
10628.25
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
475
185
88326.25
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
500
5
2850
Bar Above 12mm dia:-
2000
11
22800
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
475
627
298205
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
475
424
201666
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
91.8
1757
161376.14
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Railing
75
13357
1001808
Approach Slab
16.8
7113
119503.1
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
25
8692
217324.5
Dismantling the existing strip seal expansion joint i/c structrual steel edge beam anchor plate etc. of the existing damaged expansion joint by cutting with gas cutter and breaking of concrete by machanical means i/c disposal of rubbish &malba etc. complete as per the direction of the Engineer-in-Charge.
16
2793
44694.56
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
16
14192
227076.32
Supplying and fixing of Elastomeric Membrane of 200mm x 2mm size for expansion joint sealing from approved manuefacturer, fixing with epoxy adhesive of approved quality complete
32
3252
104093.44
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
50
1036
51846.5
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
72
278
20061.36
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
50
282
14100
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
2060
319
658458.4
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
30000
8
248100
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
400
1052
421116
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
100
171
17156
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
100
448
44880
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
75
701
52608.75
Providing Tack coat with bitumen emulsion (RS) on prepared bituminous surface, spreading @ 0.20kg / sqm using mechanical means as per Technical Specifications and Clause -501 & 503 of MoRT&H Specifications for Road & Bridge works (5th Revision).
1280
11
15347.2
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
1280
1335
1709516.8
Providing & laying Semi Dence Bituminous Concrete of grading -2 using crushed stone Gr.-2 materials & 60/70 penetration grade of bitumen, preparing preemixed materials with hot mix plant, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501 and 508 of MoRT&H Specifications for Road & Bridge works (4th Revision).
51.2
9407
481645.06
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5679
11359.94
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
1280
904
1157414.4
Repair and Strengthening work for HL Bridge over Dhanei at ch 08/988 km on Budhaambo- Buguda road
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
223
209
46647.14
50mm thick
50
141
7085.5
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
273
217
59320.17
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
500
5
2850
Bar Above 12mm dia:-
500
11
5700
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
273
627
171389.4
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
273
424
115904.88
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
19.2
1757
33751.87
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
16.55
7049
116673.53
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
25
8692
217324.5
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
27.5
14192
390287.43
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
8
1036
8295.44
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
10.8
278
3009.2
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
8
282
2256
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
248
319
79270.72
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
8000
8
66160
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
223
1065
237570.82
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
50
721
36078
Providing Tack coat with bitumen emulsion (RS) on prepared bituminous surface, spreading @ 0.20kg / sqm using mechanical means as per Technical Specifications and Clause -501 & 503 of MoRT&H Specifications for Road & Bridge works (5th Revision).
198
12
2377.98
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
198
1329
263221.2
Providing & laying Semi Dence Bituminous Concrete of grading -2 using crushed stone Gr.-2 materials & 60/70 penetration grade of bitumen, preparing preemixed materials with hot mix plant, transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501 and 508 of MoRT&H Specifications for Road & Bridge works (4th Revision).
7.92
9116
72205.93
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
75
334
25093.5
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a primer coat of approved steel primer all complete.
6602.4
86
573946.63
Supplying And Applying Sikalastic®-560 (a cold-applied, one-component highly elastic, UV resistant and also eco-friendly waterborne liquid applied waterproofing membrane based on modified polyurethane technology which contributes to Green Building certification standards) after making the surface free from all loose paticle, dust, dirt, oil, grease, or nay othe cotaminants by wire brush, air blowing etc. complete as per the direction of Engineer In Charge.
198
904
179037.54
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5672
11344.44
Repair and Strengthening work for Natakiari Nallah Minor Bridge on Bhanjanagar Tillisingi Tarasingi Daspalla road at 30.950 KM
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
206.25
209
43143.38
50mm thick
30
141
4251.3
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
236.25
210
49737.71
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
100
5
570
Bar Above 12mm dia:-
200
11
2280
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
236.25
627
148317.75
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
236.25
424
100302.3
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
2
1757
3515.82
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
28.52
7203
205436.12
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
31.5
8692
273828.87
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
25
14192
354806.75
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
4
1036
4147.72
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
4
282
1128
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
331.25
319
105880.75
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3580
8
29606.6
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
10
638
6380.3
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
206.25
1062
219167.44
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
30
717
21516.9
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
6
278
1671.78
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
75
339
25461.75
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5690
11381.9
Repair and Strengthening work for Paiki Nallha Minor Bridge on Bhanjanagar Tillisingi Tarasingi Daspalla road at 29.550 KM
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
573
209
119860.14
50mm thick
50
141
7085.5
25mm thick
50
70
3516
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
673
207
139923.43
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
1000
5
5700
Bar Above 12mm dia:-
2000
11
22800
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
673
627
422509.4
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
673
424
285728.88
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
15.08
1757
26509.28
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Approach Slab
26.25
7167
188152.91
Railing
15.6
13411
209225.48
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
74.61
8692
648583.24
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
67.5
14192
957978.23
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
12.6
278
3510.74
Providing, Fitting & Fixing of Drainage Spouts in Deck slab as per approved Drawing & Technical Specifications and Section 2700 of MoRT&H Specifications for Road & Bridge works (5th Revision).
20
1036
20738.6
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
20
282
5640
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
750
319
239730
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3580
8
29606.6
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
110
638
70183.3
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
88
1061
93419.04
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
200
171
34312
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
200
448
89760
Drilling suitable holes in reinforced or plain concrete with power driven drill machine to a minimum depth of 100 mm to 200mm in RCC beams, lintels, columns and slabs to introduce steel bars for sunshades/balconies including fixing the steel bars in position using epoxy resin anchor grout of approved make but excluding the cost of reinforcement, all complete as per direction of Engineer-in-charge.
-
-
-
Upto and including 12mm dia
1500
81
122490
Upto and including 16mm dia
500
137
68590
Upto and including 20mm dia
500
161
80910
Providing and placing high strength, non shrink pre-packed free flow micro concrete having compressive strength of 60 MPa at 28 days (compresssive strength of one day should not be less than 25 MPa) as per specifications. The micro concree mix shall be prepared by mixing non shrink pre-packed free flow micro concrete powder with well graded cleaned crushed, aggregate 10mm & down (aggregate should be less than 10mm but retained on 3.36mm) in proportion of 2:1 (Two part prepack micro concrete powder : one part stone aggregate) by weight for repairing excessively damaged area of structural elements excluding reinforcement but including scaffolding, curing inclusive of all labour, materials, equipment etc. complete as per specifications and instructions of Engineer-in-Charge.
34.5
30233
1043072.66
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
50
715
35776.5
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
140
338
47369
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
45
2143
96442.2
Cleaning of silting under the span. Engagement of labours towards cleaning of silting under the span
133
452
60116
Repair of Kotibaradi bada sankha Nallah Bridge on Bhanjanagar Tillisingi Tarasingi Daspalla Road at 9.580 Km
-
-
-
Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge
-
-
-
75mm thick
105.5
209
22068.49
50mm thick
30
141
4251.3
Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.
135.5
184
24963.17
Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavation earth to the extent required and utilising the remaining earth locally for road work. by Manual Means (Depth upto 3 m)
52
92
4802.72
Supplying and filling in foundation trenches and plinth, ditches with sand well watered and rammed in layers not exceeding 23 cm. in depth with all lead and lift including cost, conveyance, loading, unloading, royalties and of all materials, cost of all labour, sundries, T&P required for the work etc. complete in all respect as per direction by the Engineer in charge.
3.9
699
2729.34
Cement Concrete of prop (1:3:6) using 40mm size crusher broken granite metal of approved quality and from approved quarry including hoisting lowering and laying concrete in layers not exceeding 15 cm (6”) thick to the required level ramming, watering and curing etc. complete including cost and conveyance of all materials with all taxes and royalities and all labour with T&P required for the work etc. complete, including dewatering if required.
15.53
5872
91203.96
Cement Concrete of prop (1:2:4) using 12mm size crusher broken granite chips of approved quality and from approved quarry including hoisting lowering and laying concrete in layers not exceeding 15 cm (6”) thick to the required level ramming, watering and curing etc. complete including cost and conveyance of all materials with all taxes and royalities and all labour with T&P required for the work etc. complete, including dewatering if required.
12.6
7519
94749.1
Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge.
-
-
-
Bar upto 12mm dia:-
100
5
570
Bar Above 12mm dia:-
200
11
2280
Providing and applying of anticorrosive treatment to exposed structural reinforcement by two coats of IPNET RB or equivalent with time interval of minimum 8 -10 hours between each coat after the application of two coats of alkaline rust converting primer. The application shall be done by brush or spray after cleaning existing reinforcement with wire / rotary wire brush to make the surfaces free from loose material, dirt, traces of corrosion etc. and throughly washing with water and allowing it to dry inclusive of all labour, materials, equipment etc. complete in all respect as per specifications and instructions of Engineer in Charge.
135.5
627
85066.9
Providing, mixing and applying bonding coat of approved adhesive on chippedportion of RCC as per specifications and direction of Engineer-In-charge complete in all respect.Epoxy bonding of new concrete to old concrete
135.5
424
57527.88
Dismantling of Prestressed / Reinforced cement concrete grade M-20 & above including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metres
11.19
1757
19671.01
R.C.C. M-40 grade including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
-
-
-
Appraoach Slab
23
6954
159957.87
R.C.C. M-20 grade in retaining wall including cost of all materials, cost of labour, machinery, T&P charges for suspended type staging / centering & shuttering suported on girders with MS bracket arrangement for cantilever portion as per approved Drawing & Technical Specifications and as per Section -1500, 1700 & 2300 of MoRT&H Specifications for Road & Bridge works (5th Revision)
59.28
12558
744487.44
Providing HYSD reinforcement for RCC works including bending, binding & placing in position as per Drawing including cost, conveyance of all materials, all labour and T&P etc complete.
46.46
8692
403875.85
Supplying, Fitting, Fixing and Placing in position Strip Seal Expansion Joints including cost, conveyance of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause-2606 of MoRT&H Specifications for Road & Bridge works (5th Revision)
27
14192
383191.29
Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.
6.75
278
1880.75
Providing and fixing drainge spouts complete as per IRC:SP-42 with 150 mm dia PVC pipe and downtake length 1m as per engineer-in-charge.
4
1036
4147.72
Providing and fixing of bi-directional retro reflactive raised pavement markers of approved colour, quality and made conforming to ASTM D-4280 made from injection moulded high impact polymer including cleaning, preparation of surface and fixing at position with approved quality adhesives including cost of all material, labour, transportation, taxes, duties, sundries, T&P etc complete.
8
282
2256
Providing and painting of Anticorrosive paint on exposed surface of superstructures and complete as per specifications and manufacture's ecomendation by approved supplier as per the direction of Engineer-in-Charge.
411
319
131372.04
Cleaning and gurbbing road land including uprooting rank vegetation, grass, bushes, shrubs, sapling and trees girth up to 300mm, removal of stumps of trees cut earlier and desposal of unservicable materials and stacking of servicable materials to be used or auctioned, up to lead of 1000m including removal and disposal of top organic soil not exceeding 150mm in thickness. (in area of light jungle)
3580
8
29606.6
Dismantling of cement concrete grade M15 & M20 including T & P & scaffolding wherever necessary , sorting the dismantled material , disposal of unservicable material with all lifts & lead of 1000 mtr
20
638
12760.6
Guniting concrete surface with cement mortar applied with compressor after cleaning surface and spraying with epoxy complete as per Technical specification etc. complete as per direction of Engineer-In-Charge.
105.5
1052
110997.61
Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diameter (20mm to 30mm) uptodepth 150 mm at required spacing making the hole & cracks dust free by blowing compressed air , sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-in-charge.
50
171
8578
Providing and injecting grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete / masonry by suitable gun/pump at required pressure including cutting of nipples after curing etc. complete as per directions of Engineer-in-charge. (The Payment shall be made on the basis of actual weight of approved grout injected)
50
448
22440
Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge.
Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this
item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2).
30
700
21010.2
Providing & Laying 25mm thick mastic asphalt wearing course with paving grade bitumen meeting the requirements given in table 500-29,prepared by using mastic cooker and laid to required level and slope after cleaning the surface including provid antiskid surface with bitumen precoated finegrained hard stone chhiping of 13.2mm nominal size at te rate of 0.005cum per 10sqm and at an approximate spacing of 10cm centre to centre in both directions pressed into surface when the temprature of surface is not less than 1000C,protruding 1mm to 4mm over mastic suface,all complete as per clause 515.
175.5
1331
233764.25
Providing & erecting Retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity gradse sheeting vide clause 801.3 fixed over aluminium sheeting 2mm thick supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos firmely fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, 60 cm below ground level as per approved design.
-
-
-
90 cm equilateral triangle
2
5660
11321.26
Grouting aprons & revetments of 23cm deep with cement concrete (1:3:6) using 25mm size crushed stone aggregates including cost, conveyance, royality of all materials & cost of all labour etc complete as per approved Drawing & Technical Specifications and Clause - 2504 of MoRT&H Specifications for Road & Bridge works (5th Revision)
150
331
49729.5
Rough stone dry packing on Approns and Revetments with hard granite stone 30cm and above size including cost,conveyance royality of all materials and labour charges etc.complete.
45
2024
91116.45
Randum Rubble hard granite stone masonry wth sand grouted in foundation including all cost , carriage & royality etc complete
84
3380
283972.92
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
386
86
33554.98
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%