Works Department Tender

RCC M20 having compressive strength of 20mpa, target mean strength of 30mpa, for150mm cubes at 28 days curing as per IS-456-2000 & I.R.C-212000 test conducted in accordance with I.S. 516 using 20mm & down graded size crusher broken hard granite coarse aggregate of approved quality and from approved quarry & other materials as per section 302 of I.R.C.21-2000 & IS-456-2000 of approved quality including centering, shuttering & form works for providing smooth & water tight surface, hoisting, lowering & laying concrete in layers not exceeding 30 cm. compacted thickness, compacting with mechanical vibrators true to lines, grades as per drawing & technical specifications, watering & curing for 28 days including basic cost, conveyance, royalties of all materials with all leads & lift, cost of all labour T&P, including labour cess but excluding GST & equipment required for mixing, transporting & placing in position vibrating, compacting, finishing & curing including all incidental expenses complete in all respect as per direction of the E.I.C. but excluding the cost of M.S. rods or Tor steel and binding wire & labour charges for bending binding & tying the grills Coumn Footing

Column Superstructure

Column Superstructure Head room

Plinth Band

Lintel

Roof Beam

Roof Beam Head Room

Chajja average 65mm thickness

Chajja average 65mm thickness Head Room

Staircase

Roof slab

Supplying, cutting, straightening the bent up M.S. Rods or Tor steel, using SAIL / TATA / RINL / JINDAL STEEL / SHYAM STEEL (grade Fe 5OOD} etc. including bending, binding, welding jointing if necessary and tying the grills and placing in position as required for R.C.C. works and for providing required no of fan hooks hoisting, lowering, laying including basic cost, conveyance of all M.S. Tor steel and binding wires of 18· to 20 gauge as required for the work bending, binding and tying the grills in all floors (Payment will be made on weight of M.S. Tor steel only and no separate payment will be made towards the weight of binding wires) etc. including labour cess but excluding GST complete as per specification & direction of Engineer-in-Charge (First Floor)

Head room

Fly ash brick masonry in cement mortar (1:6) in Foundation and Plinth using (25x12 x8cm) size bricks after immersing the bricks for six hours in water before its use including, splays cutting, circular moulding and carbelling, champering and similar such type of works watering, curing etc. all complete including basic cost, conveyance, royalties of all materials and cost of all labour, and T&P required for the work etc. including labour cess but excluding GST complete (Crushing strength of bricks should not be less than 75kg to 99 kg/cm2 with dimensional tolerance ±2%)

Fly ash brick masonry in cement mortar (1:6) in Superstructure using (25x12x8cm) size bricks after immersing the bricks for six hours in water before its use including, splays cutting, circular moulding and carbelling, champering and similar such type of works watering, curing etc. all complete including basic cost, conveyance, royalties of all materials and cost of all labour, and T&P required for the work etc. including labour cess but excluding GST complete (Crushing strength of bricks should not be less than 75kg to 99 kg/cm2 with dimensional tolerance ±2%) as per specification & direction of the Engineer -in-Charge

Head room

12mm (½") thick cement plaster (1:6) over brick masonry finished smooth, after racking out the joints including watering and curing etc. with basic cost, conveyance, royalties of all materials and cost of all labour and T&P required for the work etc. including labour cess but excluding GST complete as per specification & direction of the Engineer-in-charge

Head room

16mm (5/8") thick cement plaster (1:6) over brick masonary finished smooth, after racking out the joints including watering and curing etc. with basic cost, conveyance, royalities of all materials and cost of all labour and T&P required for the work etc. including labour cess but excluding GST complete as per direction of the Engineer-in-charge

Head room

6mm thick cement plaster (1:4) over R.C.C. surface finished smooth with proper slope after chipping, chiselling and cleaning the roof including hoisting, watering, curing, basic cost, conveyance, royalities of all materials and cost of all labour, T&P. required for the work etc. including labour cess but excluding GST complete

Supplying, fitting and fixing of Vitrified tile in floor of size 600x600mm plain / ivory of approved make conforming to IS 13755 laid on 20mm thick cement mortar (1:4) (1 cement : 4 course sand) and filling joints with white cement of approved quality including basic cost of all materials, labour, T&P etc. required for the work all complete as per direction of Engineer-in-charge

Supplying, fitting and fixing of vitrified tile of size 600x600mm in dado & skirting on 12mm thick bed of cement mortar (1:3) jointed with neat cement slurry mixed with pigments using white cement in grating to match the shade of the tile etc. including basic cost, conveyance, royalties of all materials and labour, T&P required for the work etc. including labour cess but excluding GST complete as directed by the Engineer-in-charge

Finishing wall surfaces of wall with acrylic wall primer (water bound) one coat over inside surface of wall including basic cost, conveyance, of all materials, all labour, T&P. required for the work etc. including labour cess but excluding GST complete as per direction of the Engineer-in-charge

Head room

Finishing wall surfaces of wall with acrylic wall putty (water based) of approved make and finished smooth and even surface to receive painting including basic cost, conveyance, of all materials, all labour, T&P. required for the work etc. including labour cess but excluding GST complete as per direction of the Engineer-in-charge

Finishing wall with plastic emulsion paint of approved shade two coats to surface of walls including basic cost of paint, conveyance of all materials, labour, T&P. required for the work etc. including labour cess but excluding GST complete as per direction of Engineer-in-charge

Head room

Finishing wall surfaces of wall with weather coat acrylic emultion paint (Peach bloom) two coats over outer side surface of wall including basic cost, conveyance, of all materials, all labour, T&P. required for the work etc. including labour cess but excluding GST complete as per direction of the Engineer-in-charge

Head room

Supplying, fitting and fixing of Unplasticised Poly Vinyl chloride (UPVC) (FENSTA) / NCL VEKA Ltd) two track - two pannel sliding window shutter 60- series duly manufactured using UPVC reinforced profiles of 108 mm x 45mm x 2.5mm for outer frame & window sash of 39mm x 58mm x 2.5mm capable of mounting single glazing system, structurally reinforced with hot dip galvanised up to 50 microns of minimum thickness of 1.5mm prefabricated & welded through fusion welding the window frame shall be fitted with 6mm thick clear toughened glass of SAINT-GOBIN make duly fixed with EPDM weathering seal resistant and the system is to be installed using reinforced large coupler at the side using anchor fasteners silicon rubber sealant easy / glazing / deglazing at site etc. including basic cost and conveyance of all materials, accessories, labour charges, materials & product conforming to ASTM D 638-14 EN-477-95 and other applicable codes and standards as per specification and direction the Engineer-in-charge

Supplying, fitting and fixing of Unplasticised Poly Vinyl chloride (UPVC) (FENSTA) / NCL VEKA Ltd) casement door shutter -60- series duly manufactured using UPVC reinforced profiles of 60mm x 55mm x 2.5mm for outer frame 102mm x 60mmx 2.25mm for casement door sash profile and 74mm x 60mm x 2.5mm mullion profile capable of mounting single glazing system, structurally reinforced with hot dip galvanised up to 50 microns of minimum thickness of 2.0mm prefabricated & welded through fusion welding the door sash shall be fitted with 12mm thick WPC board of Greenply make duly fixed with EPDM weathering seal resistant accesories like clipping locking system made of aluminium 1 no. per set sashes and the system is to be installed at the side using anchor fasteners silicon rubber sealant easy / glazing / deglazing at site etc. including basic cost and conveyance of all materials, accessories, labour charges, materials & product conforming to ASTM D 638-14 EN-477-95 and other applicable codes and standards as per specification and direction the Engineer-in-charge

Supplying, fitting and fixing M.S. door & window grills, grill gates made of M.S. flat/square bar of approved specification design fitted & fixed including cutting the grooves in brick or RCC structure and making good to the damages with C.C. (1:2:4), cost of nails, screws but including basic cost of grills, conveyance, of all materials, labour, T&P. etc. including labour cess but excluding GST complete as per direction of the Engineer-in-charge

Providing factory made FRP (alternately called GRP) Door frame of size 75mm x 100mm, fabricated using E-Glass chopped strand Mat (CSM), U.V. stabolized Isopthalic Gelcoat and impregnated with Isophthalic resin The thickness of the GRP skin shall not be less than 2.0mm. The door frame consist of four segments, lwhich are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw. The GRP frame shall be provided with wooden reinforcement on six location for high screw holding capacity for fixing metalic hold fast and shall be consolidated by filling with medium density foam/plaster of paris with fibre reinforcement. Six numbers of 260mm x 25mm x 5mm size 'S' shaped M.S. flat hold fast shall be provided with the frame. The material and process for manufacturing the door frame shall confirm to RV-TIFAC composites Design Centre's shandards and specifications. The finish of door frame will be approved plain colour using high quality pigments completed in all respect as per direction of the Engineer-in-charge.

Providing factory made single leaf rigid FRP (alternately called GRP) sandwich composite door shutter of 32mm thick, laminated with two GRP skins with wood grain finish, fabricated using UV-stabilized Isopthalic Gelcoat and one layer of 450 gsm. E-glass Chopped Strand Mat (CSM) impregnated with crthopthalic, pclyester resin. The thickness of the skins shall not be less than 1.5mm, Expanded Polystyrene (EPS structural foam panel of 29mm thickness and a density of 20 kg /Cu. mtr. shall be used as core material. Wooden reinforcements made of seasoned sal wood block of cross section not less than 28mm x 32mm and also necessary sal wood reinforcements for fixing the metal fittings such as tower bolts, aldrops, handles etc. shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material, the sal wood reinforcements and the skins. The materials and process for manufacturing the door shutters shall confirm to RV-TIFAC composites Design Centre's shandards and specifications and the door shutters tested in confirmation to IS 4020-1998. The finish of door shutter will be plain colour white/ Ivory/ Beige/ Light grey/ Mahogany/ Teak wood or any other colour using high quality pigments. Three heavy weight mild steel, but hinges type-I (ISI marked) size 100mm are to be fitted on one side of shutter completed in all respect as per direction of the Engineer-in-charge.

Supplying, fitting and fixing of Stainless steel of 304 grade in hand railing using 50mm dia of 2mm thick circular pipe with Balustrade of size 32mm x 32mm x 2mm @0.90mtr C/C and stainless square pipe bracing of size 32mm x 32mm x 2mm in 3 rows in stair case as per approved design and specification, buffing, polishing etc. with basic cost, conveyance of all materials, labour, T&P. etc. including labour cess but excluding GST required for the complete in all respect as directed by the Engineer-in-charge in all floors

Painting two coats with enamel paints of approved shade in all floors to wood and iron works including sand papering, polishing the surface, basic cost, conveyance, of all materials, all labour and T&P. required for the work including labour cess but excluding GST including the cost of paint and primer as per the direction of the Engineer-in-charge

Supplying and filling foundation and plinth with excavated materials moorum with basic cost, conveyance, royalities and of all materials, labour, T&P required including labour cess but excluding GST for the work etc. including labour cess but excluding GST complete

Supplying, fitting and fixing M.S. door & M.S. Angle of approved specification design fitted & fixed including cutting the grooves in brick or RCC structure and making good to the damages with C.C. (1:2:4), cost of nails, screws but including basic cost of grills, conveyance, of all materials, labour, T&P. etc. including labour cess but excluding GST complete as per direction of the Engineer-in-charge

Supplying, fitting and fixing 0.45 mm thick GI trafford (Dura shine) sheet in roof including drilling holes in windties fixing of ridges valley windties etc. complete including basic cost of fittings, all labour & T&P. required for the work etc. including labour cess but excluding GST complete (cost of windties will paid separately) as per direction of the Engineer-in-charge