Sambalpur Development Authority Tender

Supply of 10 W LED Bulb in B-22 cap and with Opal Diffuser, Functioning as per Product TDS Luminaire with LED complete assembly With supply of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge MAKE:WIPRO / LT / TRILUX/REGENT/HALONIX/PHILIPS/OSRAM

Supply of 18 watt Surface mounted indoor type Round/square LED Luminaire with LED GLARE FREE opal diffuser , IP20 Efficency 120-130lm/w Lamp complete assembly With supply of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge MAKE:WIPRO / LT / TRILUX/REGENT/HALONIX/PHILIPS/OSRAM

Supply delivery, installation, testing & commissioning of 120 w High Efficent LED Flood light Made of Pressure Die Cast Alumuinium Housing suitable Lens & Toughened glass ip66 effiency of 120lm/w Similar to HALONIX Cat No. HFLD-ML01-120-CWL-R-B-SPD-HL2-P Make: Halonix/TRILUX/HALONIX/OSRAM/LT/REGENT/PHILIPS/LT

Supply delivery, installation, testing & commissioning of 30 w Integrated solar post top pole is innovative urban spark product which is made of Hot dip galvanized 3mm thick MS Sheet duly poly paint finish comrises of 4 direction PV Panel at all 4 side, integrated inbuilt LIFEPO4 Battery, High efficient charge controler and Post-top Light. Product has been designed in such a manner to utilized solar radiation through out the day by putting pv panel across the pole sides. this product available in 4 meter pole height. about PV Panel, Battery capacity, pole type and other details please refer specific Product TDS. IP 65 in terms of individual component which makes entire product Ip65. MPPT high efficient charge controller with smart battery health monitoring algorithm along with dusk to dawn Auto ON/OFF. LIFEPO4 Battery WRP Pack used with BMS inbuilt to ensure health of Battery Pack. LED post top light available in 3000K TO 6500K CCT.complete with making good to the damages as required and as per direction of Engineer-in-charge.Make:Halonix HLSSLINT09SPP01030821-30W-WP-CWL/TRILUX/WIPRO/PHILIPS/LT/WIPRO

Supply of materials, Fixing of G.I wire mesh cable tray along with hanging arrangements & supports fabrication complete. For following sizes.MAKE:LEGRAND/MK/SIEMON/PANDUIT

200x54 mm wire mesh cable tray

300x54 mm wire mesh cable tray

Supply, delivery, installation, testing & commissioning of CPRI TYPE TESTED IEC 61439 indoor floor /wall mounted type distribution boards made out of 2mm thick CR sheet metal cubicle fixed on m.s. channel base, duly acid treated for derusting, primered and painted with 2 coats of enamel paint of approved shade, dust, damp & vermin proof, having hinged door and compartmental arrangement for each equipment & busbar chamber on the top of the panel running horizontally, having provision for cable/ conduit entry, earthing studs as per specification mentioned below duly factory wired conforming to the relevant ISS and as per special conditions of contract making good the damages caused complete as per the direction of Engineer-in-charge. Make:SIEMENS/L&T/ABB/LEGRAND

MAIN - PANEL:Incomer:1 630A 4P ACB(50 KA) with Microprocessor based release having LSING protection and Icu=Ics=Icw for 1 sec with high speed closing feature with earthing, door interlock, automatic safety shutters ,1 no.630 ATS ,Bus bar: 4 nos.800A AL Busbar duly sleeved Outgoing: 3 Nos 160A TPN MCCB 36 ka with adjustable thermal setting,3Nos 250A 4P MCCB 36 ka,1 Nos 400A 4P MCCB 36 ka, & Ics = 100% of Icu with all MCCB ,SPD 4 Pole 50 KA type ( 1+11) Instruments: 1 set.LED type phase indicating lamps with control fuses ,Instruments: 1 set.LED type phase indicating lamps with control fuses ,1 no 630/5A CT operated Digital ammeter,1nos Basic mutifunction meter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated copper flat.

37 FEDDER- PANEL:Incomer:1 160A 4P MCCB(36 KA)with adjustable thermal setting Ics = 100% of Icu ,Bus bar: 4 nos.200A AL Busbar duly sleeved Outgoing: 30 Nos 16A DP MCB 10 ka,30 Nos 16A DP FUSE,30 Nos single phase energy meter Instruments: 1 set.LED type phase indicating lamps with control fuses ,Instruments: 1 set.LED type phase indicating lamps with control fuses ,1 no 160/5A CT operated Digital ammeter,1nos Basic mutifunction meter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated copper flat.of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge

UTILITY PANEL-:Incomer:1 250A 4P MCCB(36 KA)with adjustable thermal setting Ics = 100% of Icu ,Bus bar: 4 nos.250A AL Busbar duly sleeved Outgoing: 7 Nos 63A TPN MCCB 25 ka,1 Nos 40A TPN MCCB 25KA, ,1 Nos 160A 4P MCB 10 ka,1Nos 160A 3P FUSE,1 Nos three phase energy meter Instruments: 1 set.LED type phase indicating lamps with control fuses ,Instruments: 1 set.LED type phase indicating lamps with control fuses ,1 no 250/5A CT operated Digital ammeter,1nos Basic mutifunction meter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated copper flat.of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge

MDB-HVAC PANEL :Incomer:1 250A 4P MCCB(36 KA) with adjustable thermal setting & Ics = 100% of Icu ,Bus bar: 4 nos. 250A Busbar duly sleeved,outgoing:8 No 63A 4P MCCB (25kA) & Ics = 100% of Icu ,SPD 4 Pole 40 KA type ( 1+11) Instruments: 1 set.LED type phase indicating lamps with control fuses ,1 no.125/5A CT operated Digital ammeter,1nos Basic mutifunction meter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated Aluminium flat.of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge

POWER PANEL :Incomer:1 160 A 4P MCCB (25 KA) with adjustable thermal setting & Ics = 100% of Icu Bus bar: 4 nos. 160A Busbar duly sleeved outgoing:12 Nos 63A 4P MCB.'C' (10kA),Instruments: 1 set.LED type phase indicating lamps with control fuses ,1no. Digital voltmeter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated Aluminium flat.

DG SYN PANEL :supply ,installation testing commisioning of Dg To Dg synchronization Controller with Incomer:1 400 A 4P MCCB (36 KA) with 400 A 4P contactor & 250 A 4P MCCB (36 KA) with 250 A 4P contactor adjustable thermal setting & Ics = 100% of Icu With BUSCOUPLER 630 AMP ACB BREAKER EDO with contactor Bus bar: 4 nos. 800A Busbar duly sleeved outgoing: 400 A 4P MCCB (36 KA) & 250 A 4P MCCB (36 KA) with adjustable thermal setting & Ics = 100% of Icu ,Instruments: 1 set.LED type phase indicating lamps with control fuses ,1no. Digital voltmeter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated Aluminium flat.of required T&P and making connection from the suitable point outlet as per the Direction of Engineer-In-Charge

LIFT PANEL :Incomer:1 63A 4P MCCB 25 KA Bus bar: 4 nos. 63A Busbar duly sleeved OUTGOING 1 No 40A 4P RCCB, 30mA ,5 Nos 16A DP MCB, “C” Instruments: 1 set.LED type phase indicating lamps with control fuses , Digital volt meter and Ammeter Complete duly factory wired as per SLD and panel should have proper earth by suitable rated copper flat.

Supplying, laying & testing of following size of PVC insulated XLPE shethed / strip armoured aluminium / Copper conductor power cables of 1100 volt grade laid directly unground with sand cushioning, brick protection, clamped on surface of the walss / columns / existing RCC / inside masonry cable trenches / on the cable tray /throuth G.I Pipes / hume pipes / PVC pipes as the case may be, including cost of shaddles/ clamps/ markers etc but excluding the cost of G.I. Pipes / Hume pipes cpmplete with making good to the damages as required and as per direction of Engineer-in-charge.MAKE:KEI/POLYCAB/HAVELLS

3.5 core x300 sq mm Aluminium armoured cable. 2 RUN (FOR MAIN PANEL )

3.5 core x 240 sq mm Aluminium armoured Cable.(FOR HVAC/UTILITY PANEL)

3.5 core x 120 sq mm Aluminium armoured Cable.(FOR FEDDER PANEL)

3 core x 10 sq mm Aluminium armoured Cable.(FOR PANEL TO ROOM)

EARTHING

Earthing with copper earth plate 600 mm x 600mm x 3.15 mm thick ISI marked including accessories and providing masonary with cover plate having loccking arrangement and watering pipe etc (WITH charcoal and salt) as required.

Providing and fixing 4 mm dia copper wire on surface or in recess for loop earthing as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Providing and fixing 25mm x 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25mm x 5 mm G.I strip on surface or in recess for connections etc. as required.

Supply, delivery, installation and testing of ESE Air Terminal ESE-60 comprised of separate electrically isolated dual copper panels surrounding an Earthed central finial should be coated with chrome for environmental protection which will be install on the concrete base frame of size 900mm x 900 mm x 900 mm on the top of the roof of the building. The upper section of the central finial shall be rated to withstand 40KA impulse current and it should be made up of solid brass rod and its length should be more than 85mm above the surrounding panels. The insulation material used to electrically isolate the panel shall be comprised of base polymer which provides high UV resistance with die electric strength of 24-38KV/MM ESE terminal must withstand a minimum switching impulse voltage of 500KV. Its adapter should be made up of non conductive material DELRIN, which should provide good abrasion resistance, good mechanical strength, pretty good heat resistance, good electric & dielectric properties & Low water absorption. Terminal performance should be tested as per NFC 17-102:2011 standard .Terminal should be tested for impulse current withstand test in CPRI for 40 KA. Terminal shall carry 05 yrs warranty by manufacturer. MAKE:INDELEC PREVECTRON-S6.6/SATELITE-3/PP STROMKING/ESRICO DYNASPHERE 3000

Supply delivery installation and testing of 07.62 mtr long of 50 mm dia Class “B’ S.S Pipe with base plate, guying kit and mounting accessories etc. Of lightning mast pole to be installs’ at the top of the roof which shall be non corrosive and PVC insulated metallic wire rope as guy wire. The down conductor shall pass through the centre of the pole for the entire length of the pole and it will be out at bottom of the pole complete as per the site requirements

Supply & installation of 70sq.mm PVC insulated multi-sanded of single core flexible Copper cable for down conductor. It should run inside rigid PVC conduit to be fixed using SS/GI saddles & fixtures every 0.5mtr on the existing wall of the building complete as per the site requirements.

Supply delivery, Installation and testing of Maintenance free Safe Earthing Electrodes with ISI marked o3 mtr long 75 mm dia Class “B” S.S Pipe earth electrode with 50 mm X 6 mm M.S. hot dipped galvanized strip filled with a highly conductive & non-corrosive filled with compound of 02 bag @ 25 kg per bags for each earth electrode with Solid G.I. Base plate seals the unit at the bottom. Ground Filling Compound filled surrounding to earth electrode.

ROHS CERTIFIED Ground Filling Compound filled surrounding to earthing electrode. It should absorb the moisture from surrounding area and itshould be non corrosive in nature. It should maintain the constant ohmic value for long life. It should be supplied in packing of 25kgs bag. (2 Bags required for each earthing electrode.)

Lightning Strike Recorder (L.S.R.): Supply of Australian make L.S.R. It should be non electronic& non- resettable type having 7 digits display &enclosed in an IP-67 enclosure with minimum sensitivity of 1000A & maximum capacity of 220KA tested on 8/20 micro second wave from as per IEC 60-1: 1989. It should be non electronic type and does not require external power supply for working. Supplier should do on site testing of LSR, where impulse generate should be used to show working of LSR. After impulse current passing through LSR it should change the counter reading. Model: LSR.

Supply delivery laying and connecting by proper welding with earth excavation of trench of sizes 800mm deep x 300 mm wide in all kinds of soil and back filling with excavated soil of all the earth Pit complete as per the site requirements

D.G. SET

Supply, installation, testing and commissioning of silent type water cooled DG set conforming to latest environment protection regulations for emission and noise level comprising of radiator, power pack, electronic governor, vertical multi-cylinder diesel engine equipped with flywheel having Prime Power Rating of 180 KVA, 415 Volts at 1500 RPM, 0.8 lagging power factor at 415 volt suitable for 50 Hz, 3 phase system & for 0.8 Load Factor WITH AMF panel and consisting of the followings:MAKE: KOHELER,JACKSON,MAHINDRA NAVISTAR/eq

Diesel Engine:Full electronic authority diesel engine 4 stroke radiator water cooled, electric start with electronic fuel injection system of suitable BHP at 1500 RPM suitable for above output of alternator at 40 Degree C, 50%RH & at 1000 Meter MSL and conforming to BS:5514, BS:649, IS:10000, capable of taking 80% block load at the start and 10% over loading for one hour after 12 hours of continuous operation. The engine shall be fitted complete with all the required accessories.Engine mounted instrument Panel fitted with digital display for following:Start-stop switch with key, Water temperature indication ,Lubrication oil pressure indication, Battery charging indication, RPM indication,Over speed indication, Low lub. Oil trip indication,RPM indication, Engine Hours indication Alternator :Synchronous alternator rated for 180 KVA, 415 Volts at 1500 RPM , 3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated through AVR conforming to IS:4722/ BS:2613 suitable for tropical conditions and with class F/ H insulation. Accoustic Enclosure Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per specifications.enclosure, 6 hours testing, unloading & placement of DG set, Control Cables, CEIG Approval WITH INBUILT AMF PANEL.DG Set, Silencer, DEEPSEA AMF. controller, Auto Start/stop Facility, Exhaust Bellows, Battery with Leads, Battery Charger, Sub‐base Fuel Tank & First fill of Lube oil and Coolant