Rural Development Department Tender

WBM Gr-III

Providing and applying Primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and sparying primer at the rate of 0.7-1.0 kg/sqm as per Technical Specification Clause 502 including 1 % CESS & as per specification and direction of the Engineer-in-charge.

Providing and applying Tack coat with bitumen (RS-1) using emulsion sprayer at the rate of 2.0 kg/10sqm on prepared bituminous/ granular surface properly cleaned with hydraulic broom as per Technical Specification Clause 503 including 1 % CESS & as per specification and direction of the Engineer-in-charge.

WBM Surface

Bituminous Surface

Providing & laying SDBC with batch mix hot mix plant using crushed aggregate of specified grading, premixed with bituminous binder of 60/70 penetration grade, transporting the hot mix to work site, laying with a hydrostatic paver finisher wit censor control to the required grade, level, alignment, rolling with smooth wheeled, vibratory & tandem rollers to achieve the desired compaction as per clause 508 of MoSRT&H specification for road and bridge works (4th revision)

White washing two coats on parapet walls and tree trunks including preparation of surface by cleaning scraping etc. as per MORD techincal specification Clause 1915 with all labour, materials, T&P, taxes and CESS etc. complete as per specification and direction of the Engineer-in-Charge

Providing and fixing of R.C.C(1:2:4) pre cast Kilometer stones of different size with all labour, materials, T&P, taxes and CESS etc. complete as per specification and direction of the Engineer-in-Charge

Ordinary K.M stones

Painting of KM Stone

Lettering of KM Stone

200m stone (Precast)

Reinforced cement concrete M15 grade Guard stone/local stone of standard design as per IRC:25 fixed position including finishing and lettering but excluding painting as per drawing and Technical specification Clause 1704 of MORD.

New Guard posts on curve portion

Providing and fixing of retro-reflectorised, cautionary, mandatory and informatory sign as per IRC-67 -2012made of Class-B retro-reflective sheeting high intensity and high intensityPrismatic grade retro-reflective sheeting as perASTM D 4956 Type-III and IV strictly Conforming to clause 6.7 of IRC 67-2012 and vide clause 801.3, fixed over aluminium sheeting, 2.00 mm thick as per Clause 6.5.2 of IRC 67-2012 or A.C.P. (Aluminium composite panel) used for sign boards with a thermoplastic core of low density polyethylene (LDPE) between two thick sheets of aluminium with over all thickness of 4 mm and aluminum thickness of 0.5mm on both sides supported on mild steel angle post 75mm x 75mm x 6mm 2 nos and 3 nos horizontal and 1 no vertical extra supporting member of MS angel of size 50 mmx50 mm x6 mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 45 cm x 45 cm x 75 cm, 60 cm below ground level as per approved drawing including cost, conveyance, royality, taxes of all materials, labour, T & P, excavation, curing etc. complete, under supervision of Engineer-in-Charge.

Village board ( 600mm x 450 mm ) Rectangle

600 mm dia Cautionary Board

Providing and erecting direction and place identification of retro reflectorised sign boards as per IRC:67 made of 2mm thick M.S.sheet duly stove enamelled paint in white colour in front and grey colour on back with red reflective boarder of 70 mm width and required message, letters,figures with reflective engineering grade tape as per MORD specification of required shade and colour. Supported and welded on 47mm x 47mm of 12 SWG Square tube of 3050mm height duly strengthened by 25mm x 5 mm M/s flats iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450mm X 450mm x 600mm,600mm below ground level as per approved drawing and technical specification clause 1701.

1800mm x 1200mm size board