Rural Development Department Tender

a) required accessories. Earthing community kit, mounting bracket, cable manager, support angle, equipment shelf, mounting hardware, fan housing units etc, Ventilated top and bottom covers with attractive styling. It has Removable side panels with slam latches for easy access. (Make : MTS/Netrack/APW/eq make. 1 Set b) High Power 2-Way All Weather Loudspeaker with 1 x 15" LF Make: JBL/EV/BOSS/TW /eq make Audio. 3 Set c) All-Weather Compact 2-Way Coaxial Loudspeaker with 8" LF for surround Make: JBL/EV/BOSS/TW/eq make Audio. 6 Set d) All-Weather Compact Low-Frequency Speaker with 15" LF Make: JBL/EV/BOSS/TW /eq make Audio. 2 Set e) Four-channel, 1200W @ 4Ω Digital Power Amplifier Make: Crown/Powersoft/eq make. 2 Set. All the work should be done as per direction of Engineer-in-charge

f) 12 x 8 Digital Signal Processor Make: JBL/EV/BOSS or equivalent :1 Set g) Supply, Installation, Testing and Commissioning of 12 channel Compact Mixing System (4 x Mic/Line + 4 x Mic/Stereo-Line), Auxiliary’s (MON, FX, AUX) : 2 Pre, 2 Post, 2 Pre/Post switchable, F Dual stereo 24/48-bit multi effects processors JBL/EV/BOSS or equivalent. 1 Set h) Supply, Installation, Testing and Commissioning Supply of Corded/Wireless Vocal Microphone with Dynamic neodymian magnet based microphone element with frequency response of 32Hz-17kHz or better Make:-JVL, Sennheiser, BOSS/EV/Yamaha/eq make: 2 Set

Imaging/Effects/Lighting Projection System, Sky Launchers etc

a) 22k or Better DLP projector Native Contrast 2000:1,Britness uniformity 90%, Illumination life time 20000 Hrs or More, Input HDMI 2.0,1x DP1.2, 1xHDBaseT(Make : Christie/ Barco/ Panasonic/DP/eq make) 06 Nos b) Projection housing enclosure with DEC Control Interface for setup and monitoring of temperature, humidity and status indicators. Power control circuit with PID Management system compatible with the projection housing unit and display unit. (Make : Customised) 06 Nos c) Control panel with Independent Digital Led Display for Monitoring of Temperature and Humidity , exhaust control circuit, heating circuit, and power distribution for the projectors.(Make : RDM/Equivalent) 01 Nos d) Assembly and mounting of projector as per site plan with cables, mounting brackets and tilt/pan arrangement systems for projection layout. (Make : Customised) 06 Nos. All the work should be done as per direction of Engineer-in-charge

e) Lasers 5 watts RGB Eye-Magic 60 kpps scanning Safety shutter Interlock dust free area processor supported electronics optimized airflow ILDA Interlock mechanical shutter ILDA IN/OUT (Make : LPS/ HB Laser/ K-vant/eq make) 02 Nos f) Laser Show Software LPS-Real TIME Pro or equivalent. (Make : LPS/ LAYU/ Pangolin) 01 Nos g) Laser protection housing 20 - 30 °C with an accuracy of 0.3°C inside, independent from the ambient temperature in a temperature range of +5°C up to 40°C with external chiller. (Make: Customised) 02 Nos h) Weather proof dome housing for beam lights of suitable size with heat dissipation unit and acrylic covering to pass the beam. (Make: Customised) 08 Nos. All the work should be done as per direction of Engineer-in-charge

Control room Supply installation testing and commissioning of following:

a) Program server with interfaces as per the technical specs of 8 GB RAM, Intel® C612 chipset, compatible audio video interface Graphic card with DP Outs and 3U Rack mountable PC complete with keyboard mouse etc. Integrated Intel I217 Gigabit Ethernet controller. Quad channel; Up to 256GB10 2133MHz DDR4 ECC RDIMM memory. Support for 2 PCI Express® x16 Gen 2/Gen 3 graphics cards up to 300W. (Make : Dataton/ SMC/ Asus/ Dell/eq make) 02 Set b) A multi-display production and presentation Software that delivers a remarkable impact. Media Servers licence keys with 4 display monitor output. (Make : Dataton/ Coolux/ Modulo/ or Equivalent) 01 Set c) 24 inches Flat LCD Display Monitors with Optimal Resolution of 1920 x 1080 at 60 Hz having Brightness 250 cd/m² (typical). Connectivity 1 Digital Visual Interface connectors (DVI-D) with HDCP 1 Video Graphics Array (VGA) 1 USB 2.0 upstream port 2 USB 2.0 downstream ports DC power connector for Dell Sound bar (Make : Dell/Samsung/ HP/eq make) 03 Set. All the work should be done as per direction of Engineer-in-charge

d) Supply, installation testing and commissioning of 40 KVA, true on-line UPS 3 Ph double Conversion with all safeties and protection and suitable capacity sealed maintenance free 12 V batteries, with a 15-20 mins backup time on full load with MS open MS Battery rack and Nyvin cable. (Make : Eaton/Emerson/eq make) 01 Set e) DVI D, HDMI, VGA, USB etc CABLES. For All above Arrangements/Equipment’s 01 Set f) Small Business 24 port Gigabit switch and 2 x Mini GBIC fibre uplinks. Standards:- IEEE 802.3, 802.3u, 802.3x, 802.3ab. Cabling Type:-Category 5 and multi-mode fibre. Power:-100-127VAC/200-240VAC, 1.0A/0.5A, 50-60 Hz. Operating Temperature:-32 to 104ºF (0 to 40ºC). (Make : Cisco/ D-Link/ Netgear/eq make) 01 Set g) DVI/ HDMI Extender Transmitter Using Cat6 Cable.(Make : Extron/Kramer/ Milestone) 04 Nos h) DVI/ HDMI Extender Receiver Using Cat6 Cable. (Make : Extron/Kramer/ Milestone/eq make) 04 Nos i) 300 mtrs Cat5e/6 twisted unshielded/ shielded pair cable. (Make : Extron/Kramer/ Dlink/eq make) 02 Nos j) Speaker cable 16 AWG 2C ATC as per requirement. (Make : Beldon/ Krystal/ Extron/eq make) 01 Nos. All the work should be done as per direction of Engineer-in-charge

E) Cabling & Earthing 1. Electrical Panel

i) a. 200 A MCCB 35 KA 3 Pole Incomer b. 100 A MCCB for UPS IN c. 100 A MCCB for UPS OUT d. Digital Metering Set e. LED indicator light f. 32 A DP MCB g. 6-25 Amp SPMCB h. Panel Stand i. PANEL BODY WITH COPPER BUS BAR AND WIRING Supply and laying of one number cable of following sizes direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. / on surface / in pipe / conduit as required. (Make : L&T/Legrand/Siemens/Eq make) 01 Set. as per the requirement ii) 3C x 1.5 mm² PVC insulated, PVC sheathed, armoured/unarmoured, and stranded copper conductor cable 1100V grade, of ISI Marked, as required. (Make: Havells/Polycab /Kei/ RR cable/eq make) 01 Set iii) 3C x 2.5 mm² PVC insulated, PVC sheathed, armoured/unarmoured, and stranded copper conductor cable 1100V grade, of ISI Marked, as required. (Make : Havells/Polycap /Kei/ RR cable/eq make) iv) 3C x 4mm² PVC insulated, PVC sheathed, armoured/unarmoured, and stranded copper conductor cable 1100V grade, of ISI Marked as required. (Make : Havells/Polycap /Kei/ RR cable/eq make). All the work should be done as per direction of Engineer-in-charge

v) 3C x 6mm² PVC insulated, PVC sheathed, armoured/unarmoured, and stranded copper conductor cable 1100V grade, of ISI Marked as required. (Make : Havells/Polycap /Kei/ RR cable/eq make) vi) 3C x 16mm² PVC insulated, PVC sheathed, armoured/unarmoured, and stranded copper conductor cable 1100V grade, of ISI Marked as required. (Make : Havells/Polycap /Kei/ RR cable//eq make) vii) Field Junction and distribution box with 6-32 A MCB (Make : L&T/Legrand/Siemens/eq make) viii) 100 x 40 mm race way in the control room. (Make : Legrand/eq make ) ix) Supply of 100 x 100 mm water proof box for beam lights.(Make : Customised ) x) DMX /RS485 cable, 22 AWG stranded (7x30) tinned copper conductor, insulated, twisted pairs, overall shield (100% coverage) PVC outer jacket as required. (Make : Kramer/ Krystal/ Extron/ D-Link/ Polycab/eq make) . All the work should be done as per direction of Engineer-in-charge

xi) Earthing with Copper earth plate 600 mmx600x3mm thick including all accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. complete with charcoal and salt as required as per BIS specifications. (Make : Customised ) xii) 15 mmx5mm copper strip on surface/recess for connections etc. as required. (Make : Customised ) xiii) 6 SWG GI Wire on surface/recess/in ground for loop earthing along with existing cable as required. (Make : Customised ) xiv) S.I.T.C. 25 mm Pvc conduit pipe in existing trench and surface on wall with bend, saddle, PVC sleeve, screw and required accessory. (Make : Customised ) xv) Supply and fixing of control room fittings like tube lights, power points and light points. (Make : Wipro/Philips/Crompton/Panasonic/eq make ) All the work should be done as per direction of Engineer-in-charge