Public Health Engineering Organisation Tender

Supply with fitting and fixing of of D.I. Mechanical dismentaling joint for use to main uninterrupted water supply in the pipeline in case eof rpair of Flow meter as per specification and direction of Enginer - in - charge 350 mm dia

Design, Drawing ,Construction , Testing & Commissioning of Recyling Unit for 8 MLD WTP comprising of two symmetrical compartments having one walkway on the partition wall and one inlet chamber in one side to collect the water by gravity flow from filter bed,clariflocculator and overflow water from other units and one outlet chamber/ Suction chamber at the opposite side of inlet chamber including dewatering pump set,delivery pipe,inlet/ outlet arrangement,electrificationperipheral development with all ancilliary works following the design requirement with all respect and as per the direction of the Engineer-in-charge.

Centrifugal Pump with Electrification:- Supply , Installation,Testing & Commissioning of VFD compactable Centrifugal pump set conforming to IS 9079 operating at 1440 RPM with impeller, priming funnel, cock, suitable flanges at suction and delivery side. Pump shall have common shaft for pump and motor. Motor shall be suitable for working on 0.4KV ± 10%, 3 Ph, 50 Hz A.C. Supply. Motor shall be TEFC type. Pump set shall be suitable for working at various discharge and head requirements. Pump shall be erected on R.C.C. foundation block with suitable foundation bolts grouted as per the direction of the Engineer-in-charge. (including third party inspection such as RITES/TUV /PDIL/CIPET/Govt.approved agency) - Duty Condition:Head-64 Meter,Discharge-43 LPS

Design, Drawing and Construction of RCC frame structure single stored building for 33KV Indoor HT meter Cubicle Room for WTP

Design , drawing & Construction of Pumpset Foundation Base inside the sunken pump house with minimum size 2.3X1.0X1.0with M20 grade concrete over 100mm sand filling and 150mm cement concrete . The depth of foundation should be minimum 850mm below the floor level as per site requirement complete in all respect as per direction of Engineer-in-charge.

Design , drawing erection, testing commissioning of 4T E OT crane (electric operated monorail ) double garder I- section Beam with Gantry SQ bar span 6.60 meter height of lift 6 meter Electric operated monorail - 4MT

4 T double girder I-beam type-ISMB and ISMC including fabriction and installation as per manuifactures design requirement

Feeder Panel:- Supply ,fitting & fixing of Enclosure for the LT 630A Capacity ACB control panel board with APFC made out of CR sheet having Size-Height-2000MM X Breadth-4250MM X Depth-1000, Floor mounting with primer coated with Powder coated paint and provided with required gasket for dust / vermin proof with degree of protection IP42 suitable for 415V ,3 phase, 50Hz, 4 wire system fabricated up to 2MM thick (1.6 mm for doors) with panel accessories.{Panel weight consider from analysis}, 630A,4Pole,50kA/EDO, Microprocessor Based Air Circuit Breaker For Main Incomer(Make-SIEMENS/ L&T/ SCHNEIDER/ ABB/ BCH/C&S), 25A, Breaker control switches (Trip-Neutral-Close).(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/ SCHNEIDER/ ANCHOR), 25A,Local-Remote, Auto-Manual Switches.(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/ SCHNEIDER/ ANCHOR), Indicator(Red/Yellow/Green).(Make-L&T/C&S/ABB/BCH), Indicator(Blue).(Make-L&T/C&S/ABB/BCH), Three phase Digital Ammeter Accuracy class-1.0. (96 x 96 MM/MAKE--SECUR/ C&S/ TECHNO) (l.S), Three phase Digital Volt meter Accuracy class-1.0. (96 x 46 MM/MAKE--SECURE/ C&S/ TECHNO) (L.S), 10A/AC3 Auxiliary Contactor/ 230V .(Make-L&T/ BCH/ TC/ABB/ C&S /SIEMENS/SCHNEIDER/ANCHOR),6A /4Pole M.C.B.for meter wiring. (Make-L&T/BCH/TC/ABB/C&S), 6A /2Pole M.C.B.for fan & relay wiring. (Make-L&T / BCH/ TC / ABB/C&S),32A/3Pole M.C.B. (Make-L&T/ BCH/TC/ABB/ C&S) , Copper Bus-Bar(40MM X10MM)/ (50MM X8MM).Weight consider from analysis.-Each quantity as per requirement 600/5A VA-15,CL-1,ID-70MM C.T. (Make-RISHABH/KAPPA/ AE / ELMEX) (L.S), 50-63A/4Pole M.C.C.B,36kA{For light load & ancillary load}.(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/SCHNEIDER), 1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 4MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 10MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S), 4-6MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S), 10MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S)- , 25 X 25 MM PVC Cable Ducts. (Make-L&T/SALZER/ KAYCEE), 25 MM PVC Cable Ducts Cover. (Make-L&T/ SALZER /KAYCEE), 150MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.), 200MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.), PVC Tape(Make-STEELGRIP/ ANCHOR/CONA) (L.S.), MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/SALZER), Finger Type Insulator/one Bus -Bar Support For Capacitor Bank.(Make-RAMANUJ/WAGO), Bakelite sheet(Thick-4MM, Required size - 10" X 28", 10" X 18" , 10" X 8" , 28" X 28" ,35" X 28" ), 12MM PVC Spiral (L.S.), 25MM X 25MM PVC Mount (L.S.), 2.5MM² Ferrules.(L.S.), 73MM Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ) (L.S), Galvanized coated nut-bolt,Plain washer,Spring washer (L.S.) Quantity as per requirement.

45KW VFD Panel-4Nos:- Supply ,fitting & fixing of 45KW VFD, following specification:- Ambient temperature - -10 to + 50°C; up to + 60°C with derating at 2% per degree rise in temperature. Protection design - IP20 standard, NEMA Type 1-Kit ( optional), IP55/NEMA Type 12 external heatsink ( factory option). Mounting - Horizontal ( 0.75 KW to 75 kW (HD). Overload capacity - 150 % 1 min. (HD, heavy duty) or 110% / 1min. (ND, normal duty. Rated voltage - 200 to 240 VAC, -15 to +10 % 50 / 60 Hz +/-5 %. Output frequency - 0 to 590 Hz. Carrier frequency - 400V Class; 2-15 kHz up to 55KW (ND) ; 2-10 kHz from 75 kW (HD); 2 kHz from 250 kW to 355 kW (ND).Control inputs - 8 digital (sink / source), 3 analog (current/voltage), 1 pulse (HTL, max. 32 kHz), Control output - 4 relay 2 analog ( current/voltage), 1 pulse (HTL, max. 32kHz), 24 Vdc for external sensors available (max. 150 mA) Motor types - Induction Motor ( IM), permanent Magnet Motor (IPM/SPM), Synchronous Reluctance Motor(S (SynRM).Protective functions - Stall prevention, overload prevention,overtemperature prevention - and further protective functions for the motor,the application and the inverter drive. Self-monitoring - Monitoring of main components ( fans, IGBTs, capacitors, charging circuit) with alarm when reaching a certain lifetime.(Make-SIEMENS/ L&T/ SCHNEIDER /ABB/ YASKAWA) and160A/3Pole M.C.C.B,50k (Make-L&T/ ABB/ SIEMENS / BCH/ C&S/ SCHNEIDER), 250A/3P/1set of 6 Spreader Terminals. (Make-L&T/ C&S/ BCH/ TC/ABB/SCHNEIDER/SIEMENS)- Three phase Digital Ammeter Accuracy class-1.0. (96 x 48 MM/MAKE--SECUR/C&S/TECHNO), Indicator (Red/Yellow/Green).(Make-L&T/C&S/ABB/BCH/TC), Indicator(Blue).(Make-L&T/C&S/ABB/BCH/TC), 6"Cooling fan(MAKE-HIGH COOL / SALZER/ KAYCEE). 6A /4Pole M.C.B.for meter wiring. (Make-L&T/BCH/TC/ABB/C&S), 600/5A VA-15,CL-1,ID-70MM C.T. (Make-RISHABH/KAPPA/ AE / ELMEX) (L.S), 50-63A/4Pole M.C.C.B,36kA{For light load- & ancillary load-}.(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/SCHNEIDER), 1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 4MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 10MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S)-15Nos, 4-6MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S), 10MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S) , 25 X 25 MM PVC Cable Ducts. (Make-L&T/SALZER/ KAYCEE), 25 MM PVC Cable Ducts Cover. (Make-L&T/ SALZER /KAYCEE), 150MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.), 200MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.), PVC Tape(Make-STEELGRIP/ ANCHOR/CONA) (L.S.), MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/SALZER), Finger Type Insulator/one Bus -Bar Support For Capacitor Bank.(Make-RAMANUJ/WAGO)-, Bakelite sheet(Thick-4MM, Required size - 10" X 28" , 10" X 18" , 10" X 8" , 28" X 28" ,35" X 28" ), 12MM PVC Spiral (L.S.), 25MM X 25MM PVC Mount (L.S.), 2.5MM² Ferrules.(L.S.)- Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ) (L.S), Galvanized coated nut-bolt,Plain washer,Spring washer (L.S.) 6A /2Pole M.C.B.for control wiring (Make-L&T/BCH/TC/ABB/C&S), 10A/AC3 Auxiliary Contactor/ 230V .(Make-L&T/ BCH/ TC/ABB/ C&S /SIEMENS/ SCHNEIDER/ANCHOR) , 160A, Din Type HRC Fuse Links. (Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/SCHNEIDER), 63-160A, Din Type HRC Fuse Base.(Make-L&T/ SIEMENS/ ABB/BCH/ C&S/SCHNEIDER), 1kva(as per VFD control voltage required) Control transformer-, Copper Bus-Bar(25MM X6MM) weight consider from analysis, 150/5A VA-15,CL-1,ID-45MM C.T. (Make-RISHABH/KAPPA/AE/ ELMEX), Push-Button with Indicator(Make-L&T/ BCH /TC/ABB/C&S), Contact Element-NO/NC.(Make-L&T/ BCH/ TC/ABB / C&S ), 1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 1.5MM² Cable Socket (Cop). (Make-KAYCEE/ PTR /DOWELLS) (L.S), Single Pole Bus-Bar Support (Make-RAMANUJ/ WAGO), 25 X 25 MM PVC Cable Ducts.(Make-L&T/SALZER/ KAYCEE), 25 MM PVC Cable Ducts Cover.(Make-L&T/ SALZER /KAYCEE), 150MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.), 200MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.) , PVC Tape(Make-STEELGRIP/ ANCHOR/CONA) (L.S.), MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/SALZER), 12MM PVC Spiral (L.S.), 25MM X 25MM PVC Mount (L.S.)- 2.5MM² Ferrules.(L.S.), 48MM Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ), Galvanized coated nut-bolt,Plain washer,Spring washer (L.S.) as required Quantity

90KVAR APFC Panel:- Supply ,fitting & fixing of160-200A/3Pole M.C.C.B,36kA (Make-L&T/ ABB/ SIEMENS/ BCH/C&S/ SCHNEIDER), 250A/3P/1set of 6 Spreader Terminals. (Make-L&T/ C&S/ BCH/ TC/ABB/ SCHNEIDER/ SIEMENS), 6A /4Pole M.C.B.for meter wiring. (Make-L&T/ BCH /TC/ABB/C&S)-, 6A /2Pole M.C.B.for fan & relay wiring. (Make-L&T/BCH/TC/ABB/C&S), 10A /3Pole M.C.B.for 5KVAR capacitor(Make-L&T/ ANCHOR /C&S/ ABB/ BCH /SIEMENS), 20A /3Pole M.C.B.for 10KVAR capacitor(Make-L&T/ MARU/ C&S /ABB/BCH/ANCHOR/LEGRAND), 32A /3Pole M.C.B.for 15KVAR capacitor(Make-L&T/ MARU/ C&S /ABB/BCH/ANCHOR/LEGRAND), 40A /3Pole M.C.B.for 20KVAR capacitor(Make-L&T/ MARU/ C&S /ABB/BCH/ ANCHOR/LEGRAND), 1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI) (L.S), 2.5MM² single core copper cable {For 5KVAR Capacitor} (Make-POLYCAB/ HAVELLS /FINOLEX/ KEI) (L.S.), 4MM² single core copper cable {For 15KVAR Capacitor} (Make- POLYCAB/HAVELLS /FINOLEX/ KEI) (L.S.), 6MM² single core copper cable {For 20KVAR Capacitor} (Make- POLYCAB/HAVELLS /FINOLEX/ KEI) (L.S.), Indicator(Red/Yellow/Green).(Make-L&T/C&S/ABB/ BCH), Indicator(Blue).(Make-L&T/C&S/ABB/BCH), Three phase Digital Ammeter Accuracy class-1.0. (96 x 48 MM/MAKE--SECURE/ TECHNO/ C&S) (L.S), Three phase Digital Volt meter Accuracy class-1.0. (96 x 48 MM/MAKE--SECURE/ TECHNO/ C&S) (L.S) 1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/DOWELLS) (L.S)-, 2.5MM² Cable Socket (Cop). (Make-KAYCEE/ PTR/ DOWELLS) (L.S), 4-6MM² Cable Socket(Cop).(Make-KAYCEE/PTR/DOWELLS) (L.S.)-, 200/5A VA-15,CL-1,ID-45MM C.T. (Make-RISHABH/KAPPA/AE/ ELMEX), 6 Steps APFC Relay,230V (Make-EPCOS/L&T/C&S)-, 1kva/0-280V Control transformer., 7KVAR Capacitor duty contactor. (Make-EPCOS/L&T/ C&S)-, 10KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S), 16KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S)-, 20KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S)-, 5KVAR Capacitor,440V(Make-EPCOS/C&S/L&T)-, 10KVAR Capacitor,440V(Make-EPCOS/L&T/C&S)-, 15KVAR Capacitor,440V(Make-EPCOS/L&T/C&S)-, 20KVAR Capacitor,440V(Make-EPCOS/L&T/C&S)-, 4"Cooling fan(MAKE-HIGH COOL / SALZER/ KAYCEE)-, Copper Bus-Bar(25MM X6MM). (Weight consider from analysis), Single Pole Bus-Bar Support(Make-RAMANUJ/WAGO)(L.S)- Base 2pole connector(Make-RAMANUJ/WAGO)(L.S)-, MCB fixing Iron Channel / DIN 15/5.5MM -1M ( suitable for M4 Terminal).(Make-WAGO/SALZER), 25 X 25 MM PVC Cable Ducts.(Make-L&T/ SALZER / KAYCEE)-, 45 X 30 MM PVC Cable Ducts.(Make-L&T/SALZER /KAYCEE)-, 25 MM PVC Cable Ducts Cover.(Make-L&T/ SALZER /KAYCEE)- 600/5A VA-15,CL-1,ID-70MM C.T. (Make-RISHABH/KAPPA/ AE / ELMEX) (L.S), 50-63A/4Pole M.C.C.B,36kA{For light load & ancillary load}.(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/SCHNEIDER) 1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 4MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 10MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S), 1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S), 4-6MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S), 10MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S)-, 25 X 25 MM PVC Cable Ducts. (Make-L&T/SALZER/ KAYCEE), 25 MM PVC Cable Ducts Cover. (Make-L&T/ SALZER /KAYCEE), 150MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.), 200MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.)-, PVC Tape(Make-STEELGRIP/ ANCHOR/CONA) (L.S.), MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/SALZER)- , Finger Type Insulator/one Bus -Bar Support For Capacitor Bank.(Make-RAMANUJ/WAGO)-, Bakelite sheet(Thick-4MM, Required size - 10" X 28" = , 10" X 18" =, 10" X 8" = , 28" X 28" =,35" X 28" =), 12MM PVC Spiral (L.S.), 25MM X 25MM PVC Mount (L.S.)- 2.5MM² Ferrules.(L.S.)- , 73MM Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ) (L.S), Galvanized coated nut-bolt,Plain washer,Spring washer (L.S.) 1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/DOWELLS) (L.S)-, 2.5MM² Cable Socket (Cop). (Make-KAYCEE/ PTR/ DOWELLS) (L.S), 4-6MM² Cable Socket(Cop).(Make-KAYCEE/PTR/DOWELLS) (L.S.)-, 200/5A VA-15,CL-1,ID-45MM C.T. (Make-RISHABH/KAPPA/AE/ ELMEX), 6 Steps APFC Relay,230V (Make-EPCOS/L&T/C&S)-0.25, 1kva/0-280V Control transformer., 7KVAR Capacitor duty contactor. (Make-EPCOS/L&T/ C&S)-, 10KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S)-, 16KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S)-, 20KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S), 5KVAR Capacitor,440V(Make-EPCOS/C&S/L&T)-, 10KVAR Capacitor,440V(Make-EPCOS/L&T/C&S), 15KVAR Capacitor,440V(Make-EPCOS/L&T/C&S), 20KVAR Capacitor,440V(Make-EPCOS/L&T/C&S), 4"Cooling fan(MAKE-HIGH COOL / SALZER/ KAYCEE)-, Copper Bus-Bar(25MM X6MM). (Weight consider from analysis), Single Pole Bus-Bar Support(Make-RAMANUJ/WAGO)(L.S)-, Base 2pole connector(Make-RAMANUJ/WAGO)(L.S), MCB fixing Iron Channel / DIN 15/5.5MM -1M ( suitable for M4 Terminal).(Make-WAGO/SALZER), 25 X 25 MM PVC Cable Ducts.(Make-L&T/ SALZER / KAYCEE), 45 X 30 MM PVC Cable Ducts.(Make-L&T/SALZER /KAYCEE), 25 MM PVC Cable Ducts Cover.(Make-L&T/ SALZER /KAYCEE) as per Quantity requirement

Installation and commissioning of panel. L.T 300MM²,3½Core/ X 1R,Armoured,Aluminium Cable.(Make-HAVELLS/POLYCAB /FINOLEX/KEI) {For transformer to panel DG to panel)

L.T 25MM²,3.5Core/ ,Armoured, Aluminium Cable.(Make-HAVELLS/ POLYCAB /FINOLEX/KEI) {For transformer to panel DG to panel)

L.T 10MM²,4Core/ ,Armoured, Aluminium Cable.(Make-HAVELLS/ POLYCAB /FINOLEX/KEI) {For transformer to panel DG to panel)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/ METAL pipe as required. Above 185MM² and upto 400MM²

Upto 35MM² and upto 95MM² (For 3½core/25MM²-50Mtr )

Upto 35MM² (For 4core/10MM²-50Mtr )

50MM² single core/ X 3R flexible copper cable.(Make-HAVELLS/ POLYCAB/ FINOLEX/KEI)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35MM² and upto 95MM²(cop)

50MM² Cable Socket(Cop). (Make-KAYCEE/PTR/DOWELLS)(L.S.)

Supplying and installing following size of perforated painted with powder coating M.S cable trays with perforation not more than 17.5%, in convenient section, joined with connectors, suspended from the celling with M.S suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width X 50 mm depth X 1.6 mm thickness.

300 mm width X 50 mm depth X 1.6 mm thickness.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300MM² (70mm) {Alu}

3 X 50MM² (28mm) {cop}

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300MM² {Alu}

Supplying , installation and testing of maintenance free safe Earthing Electrodes with ISIG.I pipe dia 75mm as Secandary electrode with wall thickness of 2.6 mm and the primary Earthing Electrode will be 50mm X 6mm X 1no M.S hot dipped galvanized strip filled with a highly conductive & non - corrosive compound in between the primary Earthing and the secandary earthing the surface area in will be 7,06,500 sqmm for 3mtrs length and cross sectional primary conducting area is 300 sq,mm an solid GI. base plat seals the unit at the bottom and providing of masonary enclosure with cover plates as per direction of EIC(MES-GFC ground filling compound will be provided in 25kgs Bags )(MES-GFC ground filling compound will be provided in 25 kg bags ) (2 bags required for each earthing electrode ) 2 nos earthing connection all motors and 2nos earthing connect in all panel.

Providing and fixing 25 mm X 5 Mm G.I . Strip on surface or in recess for connections etc. as required.

First aid box , shock treatment chart (Odia/ Hindi/English) 8mm thick rubber mat. Danger board (200mm x 1500mm)

Supply, installation, testing and commissioning of 250 KVA, 0.44KV Silent diesel generating set three phase, air cooled/water with standard manual control panel having batteries & leads with stand ,AVM pads,acquastic enclosure,load side terminal box for cable termination,powering cable 8 run 400Sqmm 3.5 core aluminium armoured cable upto 30m,cable termination,earthing with GI earth plate 600mmX 6mm thick & GI Flat 50mm X 6mm thick-2Nos,earthing with Cooper earth plate 600mmX 3mm thick & GI Flat 50mm X 6mm thick-2Nos including transportation ,loading, unloading (including third party inspection such as RITES/TUV /PDIL/CIPET/or any othervgovt recongnised institution/factory inspection by engineer not below the rank of Assistant Exective Engineer testing and trial run of atleast for four days including pol during trial run all complete

Providing & Fixing of IK07 IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminum LM6/ ADC12 material with heat dissipation fins on housing with UV stabilized PC/Toughened Glass cover (UV stablzation report submitted for UV cover ) and secondary lens on each LED & should be SMD type . The System level Luminaire efficacy =120 lm/ wt with High Power LEDs is to be used and potted driver must be potted & has a unique BIS R number with Input Voltage AC 120 to 270 V AC with High voltage Cutoff @=300 V AC and Auto resetting Safety ,Input Frequency 50Hz±3% Power Factor 0.95 driver Efficiency 85% ,THD(I) 70 and CCT 5700K +355K. Surge protection shall be min ≥ 4 KV internal and min 10 KV external. driver should be Phase to phase protection of 440 V for 4 Hrs. Manufactures Word Mark/Name Engraved/Embossing on die cast housing to allow traceability/authenticity. Fixture shall be AS PER IS 10322 Complianced. LED street light fixture 60watt

Octagonal MS Poles made of S-355JO grade steel sheet , folded lengthwise to obtained Octagonal shape, having single longitudinal seam weld and hot dipped galvanised internally & externally in accordance with IS 2629(5.0METER HEIGHT)

Electrical and MCC Control Room (12X6) One Storey Building .

Construction of RCC Base for 250 KVA DG set at intake well pump house

Desiging, supplying, installing, commissioning & testing of CCTV IR water proof camera suitable for upto 100ft. with control key board, DVR, Hard Disk,cables, UPT transreceivers etc. complete with not less than following specifications 1. Four numbers of IP Camera with night vision functionality with range up to 30 meters. Camera construction shall be suitable for weather proof outdoor installation. 2. Eight Channe DVR withmetal body consturction, having software features of motion detect recording. 3. 3.5 inch 2 GB HDD 4. 8 port POE Switch 5. 32 inch LED Screen, Keyboard & mouse .Make- Hikvision, CP Plus, Evision, Honeywell all complete as per specification and direction of Engineer-in-charge.

Supplying all labour and T&P for providing and laying MS pipe and specials confirming to IS 3589/99 of quality grade FE 410/ GI Pipe (Medium) confirming to specification of following nominal dia and including transportation of pipes and fitting to site etc all complete as per the direction of E.I.C. 150mm dia M.S.Pipe (4.50mm thick)

150mm dia M.S. Flange.(12mm thick)

150mm dia x 45' M.S. Bend

Supplying all labour and T&P for cutting of following dia MS pipe of following thick in treanches by gas cutter set of pocket etc all complete 150mm dia

Supplying all labour and T&P for jointing following dia MS pipe up to 8.0mm thick in treanches by electric arc welding & genetator set of pocket etc all complete 150mm dia

For Proposed WTP Supplying all materials Labour & T & P for Fixing Ductile Iron Actuator Sluice Valve / NR Valve with double flanged ends for water works purposes conforming to IS specification for the following nominal diameters as per specification complete including cost of Sluice valve . 150mm dia D/F Actuator Sluice Valve (PN1.6) (KIRLOSKAR/VAGUE/TALIS)

150mm dia D/F Non Return Valve (PN1.6)(KIRLOSKAR/VAGUE/TALIS)

Boundary wall:- Supplying all labour, T&P and Earthwork in all kinds of soil leveling the bed & including sundries, supervision charges, contractor profit & labour cess etc, & as per the direction of engineer- in-charge. i)Column Base

Supplying all materials, labour, T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all materials to work site, payment of royalty, contractor profit & labour cess etc, all complete as per specification and direction of Engineer-in-charge. i)Column Base

Supplying all labour, T&P and providing Cement Concrete (1:3:6) using 4cm HBG crusher metal including watering curing, supervision conveyance of all materials to worksite, payment of royalty, taxes etc. all complete in F&P as per specification and direction of the Engineer-in-charge. i)Column Base

R.C.C work in ground floor of M-20 grade with 20mm & down grade crusher broken hard Granite chips including hoisting & laying with cost of all labour, materials with all taxes, lead ,T & P etc all complete . i)Column Base,plinth beam,beam,column

Supplying all materials, labour, T&P and providing rigid and Smooth centering and shuttering for R.C.C. works including False work and dismantling them after casting including Conveyance of all materials to Work site, payment of royalty,contractor profit & labour cess etc all complete as per specification and direction of Engineer-in-charge. i)Tappered,column bas , upto plinth , plinth beam,

Supplying all materials, labour, T&P and providing rigid and Smooth centering and shuttering for R.C.C. works including False work and dismantling them after casting including Conveyance of all materials to Work site, payment of royalty,contractor profit & labour cess etc all complete as per specification and direction of Engineer-in-charge. i)Column

Supplying all materials, labour, T&P and providing M.S. reinforcement for R.C.C. work including cutting, bending, binding and laying the grill and position including cost of binding wire 18 to 20 gauge, conveyance of all materials to Work site, payment of royalty, contractor profit & labour cess etc all complete as per specification and direction of Engineer-in-charge (SAIL STEEL TMT-EQR 500/IS 1786 Fe 500 D) Taking 0.80Qtl /cum

Supplying all materials, labour, T&P and Providing Brick work with Fly Ash Bricks 25cm x 12cm x 8cm size having crushing strength not Less than 75kg/cm² with dimensional tolerance ± 8 percent in cement mortar(1:6 ) in S/S including cost of conveyance & royalty, sundries & watering for curing & supervision charges, contractor profit & labour cess etc, all complete as per the direction of Engineer-in-charge. wall

Supplying all materials, labour, T&P and making 12mm thick cement plaster in cement mortar (1:6) for brick or stone masonry work for brick work including watering, curing, conveyance of all materials to worksite, payment of royalty, contractor profit & labour cess as per the direction of engineer-in-charge. (Outside wall)

Supplying all materials, labour, T&P and making 16mm thick cement plaster in cement mortar (1:6) for brick or stone masonry work for brick work including watering, curing, conveyance of all materials to worksite, payment of royalty, contractor profit & labour cess as per the direction of engineer-in-charge. (Inside wall)

Supplying all materials, labour, T&P and filling of foundation and plinth with excavated materials with all kinds of soil as per the direction of engineer-in-charge. 1/3 of Qnty of item Earth work

Supplying all materials, labour, T&P and providing Priming 1 coat with any appproved Primer including all materials, conveyance, contractor profit & labour cess etc, all complete as per the direction of Engineer-in-charge. (on Plastered surface)

Supplying all materials, labour, T&P and providing two coat of Weather Coats with any approved shades including cost of conveyance, brushes, sundries, contractor profit & labour cess etc all complete as per the direction of Engineer-in-charge

Pillar and Gate Supplying all labour, T&P and Earthwork in excavation in Stony earth and gravels mixed with stone & boulders not exceeding 0.014 cum in volume with in 50mtr. Initial lead & 1.50m. initial lift including rough dressing, breaking clods & laying in layers not exceeding 0.30m In depth, leveling the bed & including sundries, supervision charges, contractor profit & labour cess etc, & as per the direction of engineer- in-charge. i)Column base

Supplying all materials, labour, T&P and filling in foundation and plinth with sand well watered and rammed including conveyance of all materials to work site, payment of royalty, contractor profit & labour cess etc, all complete as per specification and direction of Engineer-in-charge.

Supplying all labour, T&P and providing Cement Concrete (1:3:6) using 4cm HBG crusher metal including watering curing, supervision conveyance of all materials to worksite, payment of royalty, taxes etc. all complete in F&P as per specification and direction of the Engineer-in-charge. i)Column base

R.C.C work in ground floor of M-20 grade with 20mm & down grade crusher broken Granite chips (Beam , column, column base, tapper)

Supplying all materials, labour, T&P and providing rigid and Smooth centering and shuttering for R.C.C. works including False work and dismantling them after casting including Conveyance of all materials to Work site, payment of royalty,contractor profit & labour cess etc all complete as per specification and direction of Engineer-in-charge.(Column base , plinthbeam, Column, )

Supplying all materials, labour, T&P and providing rigid and Smooth centering and shuttering for R.C.C. works including False work and dismantling them after casting including Conveyance of all materials to Work site, payment of royalty,contractor profit & labour cess etc all complete as per specification and direction of Engineer-in-charge., (Column, )

Supplying all materials, labour, T&P and providing M.S. reinforcement for R.C.C. work including cutting, bending, binding and laying the grill and position including cost of binding wire 18 to 20 gauge, conveyance of all materials to Work site, payment of royalty, contractor profit & labour cess etc all complete as per specification and direction of Engineer-in-charge (SAIL STEEL TMT-EQR 500/IS 1786 Fe 500 D) taking 0.8 Qtl/cum

6 mm thick cement plaster (1:4) to R CC surfaces finished smooth including closed deep chiping and slury treatment

Supplying all materials, labour, T&P and filling of foundation and plinth with excavated materials with all kinds of soil as per the direction of engineer-in-charge. 1/3 of Qnty of item earth work

Supplying all materials, labour, T&P and providing Priming 1 coat with any appproved Primer including all materials, conveyance, contractor profit & labour cess etc, all complete as per the direction of Engineer-in-charge. (on Plastered surface)

Supplying all materials, labour, T&P and providing two coat of Weather Coats with any approved shades including cost of conveyance, brushes, sundries, contractor profit & labour cess etc all complete as per the direction of Engineer-in-charge

Supplying all materials, labour, T&P and fitting & fixinh of SS Gate proving rincluding cost of conveyance , brushess sundries , contractor profit & labour cess etc all complet as per the direction of EIC, 2 Leaf SS Gate (Size 6.0 M x 1.8 M Ht.) @ 30 KG/Sqm

1 Leaf SS Gate (Size 1.3 M x 1.8 M Ht.) @ 30 KG/Sqm

Approch Road for ESR side Supplying all materials, labours, T&P , and filling of road surface with borrow earth (1.0mtr ) from the approved Quantity and compacting to the required density with testing including cost of royality lead & transportation & labour cess etc all complete as per the direction of EIC,

Construction of granular sub-base by providing Coarse graded Grading-II material as per Table 400-2, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401, with Add 25% of metal volume for consolidation

roviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per Clause 406 of MoSRT&H Specifications for Road & Bridge works.(Latest Revision)

Supplying all labour, T&P and providing Cement Concrete (1:3:6) using 4cm HBG crusher metal including watering curing, supervision conveyance of all materials to worksite, payment of royalty, taxes etc. all complete in F&P as per specification and direction of the Engineer-in-charge.

M30 Grade concrete using 20mm to 10 mm size crushed stone aggregate mixed by concrete miser layiong in layers compacting by vibrator with proper cambering and filling berm by excavated earth and all leads and lift including frame work etc .complet in all respective as per scope & Technical specification

5 Year Annual maintenance (Including contribution towards EPF, ESI, Labour cess, Contractors Profit & OH Charges but excluding cost of chemicals & Energy charges) Supply of manpower consisting of 2 number of semi skilled, 2 number of skilled and 1 no of high skilled manpower in daily basis for 5 year operation and maintenance as following. WTP- Supplying of bulb, tube, all electrical mechnixcal repairs of every component of WTP including repair of fans , blowers, pumps, anuual painting , maintaining sanitation in WTP premises. PUMP AND MOTOR- Minor repair of centrifugal/submersible pump set at WTP (including 100% standby) for prentive maintenance of greasing, change of gland packing, bush, tightening of nuts and bolts etc. all complete as per the instruction of Engineer-in-charge.