Public Health Engineering Organisation Tender

Supply with fitting and fixing of 350 mm dia. D.I. Mechanical dismentaling joint for use to main uninterrupted water supply in the pipeline in case eof rpair of Flow meter as per specification and direction of Enginer - in - charge

Centrifugal Pump with Electrification:- Supply , Installation,Testing & Commissioning of VFD compactable Centrifugal pump set conforming to IS 9079 operating at 1440 RPM with impeller, priming funnel, cock, suitable flanges at suction and delivery side. Pump shall have common shaft for pump and motor. Motor shall be suitable for working on 0.4KV ± 10%, 3 Ph, 50 Hz A.C. Supply. Motor shall be TEFC type. Pump set shall be suitable for working at various discharge and head requirements. Pump shall be erected on R.C.C. foundation block with suitable foundation bolts grouted. (including third party inspection such as RITES/TUV /PDIL/CIPET/Govt.approved agency) -(3 Nos) Duty Condition:Head-66 Meter,Discharge-42 LPS

Construction,Design & drawing of Building for 33KV Indoor HT meter( Cubicle) Room with double storeyed foundation for WTP all complete as per the direction of E.I.C.

Design , drawing & Construction of Pumpset Foundation Base inside the sunken pump house with minimum size 2.3X1.0X1.0 with M20 grade concrete over 100mm sand filling and 150mm cement concrete . The depth of foundation should be minimum 850mm below the floor level as per site requirement complete in all respect as per direction of Engineer-in-charge.

Design, Drawing ,earation, testing & Commissioning of 4T EOT crane (electric operatored monorail) double grader I-section Beam with Gantry SQ bar span 6.60 meter height of lift 6 meter, Fabrication and hosting in place Rail Grader at pump house. Electric operated monorail - 4MT

Supplying, Installing & commisioning of 4T Double Girder I -Beam Type E. O. T crane with Gantry SQ bar span 6.60 meter height of lift 6meter,all complete as per the direction of E.I.C

Supply,Fitting & fixing of Enclosure for the LT 630A Capacity ACB control panel board with APFC made out of CR sheet having Size-Height-2000MM X Breadth-4250MM X Depth-1000, Floor mounting with primer coated with Powder coated paint and provided with required gasket for dust / vermin proof with degree of protection IP42 suitable for 415V ,3 phase, 50Hz, 4 wire system fabricated up to 2MM thick (1.6 mm for doors) with panel accessories.{Panel weight consider from analysis}-1026 KG, 630A, 4Pole, 50kA/ EDO, Microprocessor Based Air Circuit Breaker For Main Incomer(Make-SIEMENS/ L&T/ SCHNEIDER/ ABB/ BCH/C&S)-2 NOS,25A, Breaker control switches (Trip-Neutral-Close).(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/ SCHNEIDER/ ANCHOR)2 NOS,25A,Local-Remote, Auto-Manual Switches.(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/ SCHNEIDER/ ANCHOR)2 NOS, Indicator(Red/ Yellow/Green). (Make-L&T/C&S/ABB/BCH)10 NOS, Indicator (Blue). (Make-L&T/ C&S/ ABB/ BCH)2 NOS, Three phase Digital Ammeter Accuracy class-1.0. (96 x 96 MM/MAKE--SECUR/ C&S/ TECHNO) (l.S)2 NOS,Three phase Digital Volt meter Accuracy class-1.0. (96 x 46 MM/MAKE--SECURE/ C&S/ TECHNO) (L.S)2 NOS 10A/AC3 Auxiliary Contactor/ 230V .(Make-L&T/ BCH/ TC/ABB/ C&S /SIEMENS/SCHNEIDER/ANCHOR)4 NOS,6A /4Pole M.C.B.for meter wiring. (Make-L&T/BCH/TC/ABB/C&S)2 NOS,6A /2Pole M.C.B.for fan & relay wiring. (Make-L&T / BCH/ TC / ABB/C&S)2 NOS,32A/3Pole M.C.B. (Make-L&T/ BCH/TC/ABB/ C&S) 3 NOS,Copper Bus-Bar(40MM X10MM)/ (50MM X8MM).Weight consider from analysis. 108 KG,600/5A VA-15,CL-1,ID-70MM C.T. (Make-RISHABH/KAPPA/ AE / ELMEX) (L.S)6 NOS,50-63A/4Pole M.C.C.B,36kA{For light load-1nos & ancillary load-1nos}.(Make-L&T/ SIEMENS/ ABB/ BCH/ C&S/SCHNEIDER)3 NOS,1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S)60 MTR,4MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S)45 MTR,10MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S)51 MTR,1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S)60 NOS,4-6MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S)45 NOS,10MM² Cable Socket (Cop). (Make-KAYCEE/PTR/ DOWELLS) (L.S)48 NOS,25 X 25 MM PVC Cable Ducts. (Make-L&T/SALZER/ KAYCEE)3 NOS,25 MM PVC Cable Ducts Cover. (Make-L&T/ SALZER /KAYCEE)3 NOS, 150MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.)20 NOS,200MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.)60 NOS,PVC Tape(Make-STEELGRIP/ ANCHOR/CONA) (L.S.)2 ROLE,MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/SALZER)2 NOS,Finger Type Insulator/one Bus -Bar Support For Capacitor Bank.(Make-RAMANUJ/WAGO)80 NOS,Bakelite sheet(Thick-4MM, Required size - 10" X 28" = 4nos, 10" X 18" = 10nos, 10" X 8" = 2nos, 28" X 28" = 4nos,35" X 28" = 2nos),12MM PVC Spiral (L.S.) 2 MTR,25MM X 25MM PVC Mount (L.S.)30 NOS,73MM Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ) (L.S) 30 MTR,Galvanized coated nut-bolt,Plain washer,Spring washer (L.S.)15 KG.

45KW VFD, following specification:- AmbieSupply,Fitting & fixing of temperature - -10 to + 50°C; up to + 60°C with derating at 2% per degree rise in temperature. Protection design - IP20 standard, NEMA Type 1-Kit ( optional), IP55/NEMA Type 12 external heatsink ( factory option). Mounting - Horizontal ( 0.75 KW to 75 kW (HD). Overload capacity - 150 % 1 min. (HD, heavy duty) or 110% / 1min. (ND, normal duty. Rated voltage - 200 to 240 VAC, -15 to +10 % 50 / 60 Hz +/-5 %. Output frequency - 0 to 590 Hz. Carrier frequency - 400V Class; 2-15 kHz up to 55KW (ND) ; 2-10 kHz from 75 kW (HD); 2 kHz from 250 kW to 355 kW (ND).Control inputs - 8 digital (sink / source), 3 analog (current/voltage), 1 pulse (HTL, max. 32 kHz), Control output - 4 relay 2 analog ( current/voltage), 1 pulse (HTL, max. 32kHz), 24 Vdc for external sensors available (max. 150 mA) Motor types - Induction Motor ( IM), permanent Magnet Motor (IPM/SPM), Synchronous Reluctance Motor(S (SynRM). Protective functions - Stall prevention, overload prevention, over temperature prevention - and further protective functions for the motor,the application and the inverter drive. Self-monitoring - Monitoring of main components ( fans, IGBTs, capacitors, charging circuit) with alarm when reaching a certain lifetime.(Make-SIEMENS/ L&T/ SCHNEIDER / ABB/ YASKAWA) -1 NO 150/5A VA-15,CL-1,ID-45MM C.T. (Make-RISHABH/KAPPA/AE/ ELMEX)3 NOS,Push-Button with Indicator(Make-L&T/BCH/TC/ABB/C&S)2 NOS,Contact Element-NO/NC.(Make-L&T/BCH/TC/ABB/C&S)2 NOS,1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI)(L.S)100 MTR,1.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/DOWELLS) (L.S)150 NOS,Single Pole Bus-Bar Support (Make-RAMANUJ/WAGO)18 NOS,25 X 25 MM PVC Cable Ducts.(Make-L&T/SALZER/ KAYCEE)1 NOS,25 MM PVC Cable Ducts Cover.(Make-L&T/ SALZER /KAYCEE)3 NOS,150MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.)5 NOS,200MM cable Tie.(Make-HOODS/ ELETTRO) (L.S.)15 NOS,PVC Tape(Make-STEELGRIP/ ANCHOR/CONA) (L.S.)2 NOS,MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/SALZER)1 NO,12MM PVC Spiral (L.S.)2 NOS,25MM X 25MM PVC Mount (L.S.)30 NOS,2.5MM² Ferrules.(L.S.)30 NOS,48MM Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ)5 NOS,Galvanized coated nut-bolt,Plain washer,Spring washer (L.S.)4 NOS

Supply,Fitting & fixing of 160-200A/3Pole M.C.C.B,36kA (Make-L&T/ ABB/ SIEMENS/ BCH/C&S/ SCHNEIDER),250A/3P/1set of 6 Spreader Terminals. (Make-L&T/ C&S/ BCH/ TC/ABB/ SCHNEIDER/ SIEMENS), 6A /4Pole M.C.B.for meter wiring. (Make-L&T/BCH/TC/ABB/C&S),6A /2Pole M.C.B.for fan & relay wiring. (Make-L&T/BCH/TC/ABB/C&S),10A /3Pole M.C.B.for 5KVAR capacitor(Make-L&T/ ANCHOR /C&S/ABB/BCH/ SIEMENS),20A /3Pole M.C.B.for 10KVAR capacitor(Make-L&T/ MARU/ C&S /ABB/BCH/ ANCHOR/LEGRAND),32A /3Pole M.C.B.for 15KVAR capacitor(Make-L&T/ MARU/ C&S /ABB/BCH/ANCHOR/ LEGRAND),40A /3Pole M.C.B.for 20KVAR capacitor(Make-L&T/ MARU/ C&S /ABB/BCH/ANCHOR/LEGRAND),1.5MM² single core copper cable. (Make-POLYCAB/ HAVELLS /FINOLEX/KEI) (L.S),2.5MM² single core copper cable {For 5KVAR Capacitor} (Make-POLYCAB/ HAVELLS /FINOLEX/ KEI) (L.S.),4MM² single core copper cable {For 15KVAR Capacitor} (Make- POLYCAB/ HAVELLS /FINOLEX/ KEI) (L.S.),6MM² single core copper cable {For 20KVAR Capacitor} (Make- POLYCAB/HAVELLS /FINOLEX/ KEI) (L.S.),Indicator (Red/ Yellow/ Green).(Make-L&T/C&S/ABB/ BCH),Indicator(Blue).(Make-L&T/C&S/ ABB/ BCH),Three phase Digital Ammeter Accuracy class-1.0. (96 x 48 MM/MAKE--SECURE/ TECHNO/ C&S) (L.S),Three phase Digital Volt meter Accuracy class-1.0. (96 x 48 MM/MAKE--SECURE/ TECHNO/ C&S) (L.S),1.5MM² Cable Socket (Cop). (Make-KAYCEE/ PTR/DOWELLS) (L.S),2.5MM² Cable Socket (Cop). (Make-KAYCEE/PTR/DOWELLS) (L.S),4-6MM² Cable Socket (Cop).(Make-KAYCEE/PTR/DOWELLS) (L.S.) ELMEX),6 Steps APFC Relay,230V (Make-EPCOS/ L&T/ C&S),1kva/0-280V Control transformer, 7KVAR Capacitor duty contactor. (Make-EPCOS/L&T/ C&S),10KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S),16KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S),20KVAR Capacitor duty contactor. (Make-EPCOS/ L&T/ C&S),5KVAR Capacitor, 440V (Make-EPCOS/C&S/L&T),10KVAR Capacitor,440V(Make-EPCOS/ L&T/C&S),15KVAR Capacitor,440V(Make-EPCOS/L&T/ C&S), 20KVAR Capacitor, 440V(Make-EPCOS/ L&T/ C&S), 4"Cooling fan(MAKE-HIGH COOL / SALZER/ KAYCEE), Copper Bus-Bar(25MM X6MM). (Weight consider from analysis),Single Pole Bus-Bar Support(Make-RAMANUJ/WAGO)(L.S),Base 2pole connector (Make-RAMANUJ/WAGO) (L.S),MCB fixing Iron Channel / DIN 15/5.5MM - 1M ( suitable for M4 Terminal).(Make-WAGO/ SALZER),25 X 25 MM PVC Cable Ducts.(Make-L&T/ SALZER / KAYCEE) 45 X 30 MM PVC Cable Ducts.(Make-L&T/SALZER /KAYCEE),45 MM PVC Cable Ducts Cover.(Make-L&T/ SALZER/ KAYCEE),150MM cable Tie.(Make-HOODS/ ELLETRO). (L.S.), 200MM cable Tie. (Make-HOODS/ELLETRO).(L.S.), PVC Tape (Make- STEEL GRIP/ ANCHOR/CONA).(L.S.),12MM PVC Spiral.(L.S.),25 MM PVC Cable Ducts Cover.(Make-L&T/ SALZER /KAYCEE),25MM X 25MM PVC Mount.(L.S.),2.5MM² Ferrules. (L.S.),48MM Colour Insulated Heat Shrinkable Sleeves.(Make- RAMANUJ), Galvanized coated nut-bolt,Plain washer,Spring washer.(L.S.)

L.T 300MM²,3½Core/ X 1R, Armoured, Aluminium Cable. (Make-HAVELLS/ POLYCAB / FINOLEX/KEI) {For transformer to panel DG to panel)

L.T 25MM²,3.5Core/ ,Armoured, Aluminium Cable.(Make-HAVELLS/ POLYCAB /FINOLEX/ KEI) {For transformer to panel DG to panel)

L.T 10MM²,4Core/ ,Armoured, Aluminium Cable. (Make-HAVELLS/ POLYCAB /FINOLEX/ KEI) {For transformer to panel DG to panel)

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/ METAL pipe as required. Above 185MM² and upto 400MM²

Upto 35MM² and upto 95MM² (For 3½core/ 25MM²-50Mtr )

Upto 35MM² (For 4core/10MM²-50Mtr )

50MM² single core/ X 3R flexible copper cable.(Make-HAVELLS/ POLYCAB/ FINOLEX/ KEI)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Above 35MM² and upto 95MM²(cop)

50MM² Cable Socket(Cop). (Make-KAYCEE/PTR/DOWELLS)(L.S.)

Supplying and installing following size of perforated painted with powder coating M.S cable trays with perforation not more than 17.5%, in convenient section, joined with connectors, suspended from the celling with M.S suspenders including bolts & nuts, painting suspenders etc as required. 200 mm width X 50 mm depth X 1.6 mm thickness.

300 mm width X 50 mm depth X 1.6 mm thickness.

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300MM² (70mm) {Alu}

3 X 50MM² (28mm) {cop}

Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3½ X 300MM² {Alu}

Supply, installation and testing of Maintenance free safe Earthing Electrodes with ISI G.I pipe dia 75mm as Secondary electrode with wall thickness of 2.6 mm and the Primary Earthing Electrode will be 50mm X 6mm X 1no M.S hot dipped galavanized strip filled with a highly conductive & non-corrosive compound in between the Primary Earthing and the secondary Earthing, the surface Area in will be 7,06,500sqmm for 3mtrs length and cross sectional primary conducting area is 300 sq.mm An Solid G.I Base plat seals the unit at the bottom and providing of masonry enclosure with cover plate.as per direction of Engg.-in-charg (MES- GFC ground Filling compound will be provided in 25 kgs Bags.) (MES-GFC ground Filling compound will be provided in 25 kgs Bags.) (2 bags required for each earthing electrode.) 2nos earthing connection all motors and 2nos earthing connect in all panel.

Providing and fixing 25 mm X 5 Mm G.I . Strip on surface or in recess for connections etc. as required.

Name of sub work :- Supplying, fitting and fixing of following materials. First Aid box

Shock treatment chart (Odia / Hindi & English)

8mm thick rubber Mat

Danger board (200mm x 1500mm)

Supplying all labour and T&P for providing and laying MS pipe and specials confirming to IS 3589/99 of quality grade FE 410/ GI Pipe (Medium) confirming to specification of following nominal dia and including transportation of pipes and fitting to site etc all complete as per the direction of E.I.C. 150mm dia M.S.Pipe (4.50mm thick)

150mm dia M.S. Flange.(12mm thick)

150mm dia x 45' M.S. Bend

200mm dia M.S.Pipe (6.30mm thick)

200mm dia M.S. Flange.(12mm thick)

200mm dia x 45' M.S. Bend

Supplying all labour and T&P for cutting of following dia MS pipe of following thick in treanches by gas cutter set of pocket etc all complete

Supplying all labour and T&P for jointing following dia MS pipe up to 8.0mm thick in treanches by electric arc welding & genetator set of pocket etc all complete

Supplying all materials Labour & T & P for Fixing Ductile Iron Actuator Sluice Valve / NR Valve with double flanged ends for water works purposes conforming to IS specification for the following nominal diameters as per specification complete including cost of Sluice valve 150mm dia D/F Actuator Sluice compatible Valve (PN1.6) (KIRLOSKAR/ VAGUE/TALIS)

150mm dia D/F Non Return Valve (PN1.6) (KIRLOSKAR/ VAGUE/ TALIS)

05 years o & M (Including contribution towards EPF, ESI, Labour cess, Contractors Profit & OH Charges but excluding cost of chemicals & Energy charges) Supply of 1 number of unskilled,1 number of semiskilled,1 number of skilled and 2 numbers of high skilled in daily basis for 5 year operation and maintenance as following. WTP- Supplying of bulb, tube, all electrical mechnixcal repairs of every component of WTP including repair of fans , blowers, pumps, anuual painting , maintaining sanitation in WTP premises. PUMP AND MOTOR- Minor repair of centrifugal/submersible pump set at WTP (including 100% standby) for prentive maintenance of greasing, change of gland packing, bush, tightening of nuts and bolts etc. all complete as per the instruction of Engineer-in-charge.