Pradhan Mantri Gram Sadak Yojana Tender

Fine dressing and turfing including transportation by mechanical means with all lead and lift and placing of turf in position and ramming with thapies and including watering and cost of all labour, materials etc. complete as per Clause 309 of MORD Specification and as per direction of the Engineer in Charge.

Construction of granular sub-base (Grading III) by providing well graded material, spreading in uniform layers with grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density,complete as per MORD Technical Specification Clause 401 as per direction of Engineer-in-Charge.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening(morum and sand admixture) to fill-up the interstices of coarse aggregate, watering and compacting to the required density as per Technical Specification Clause 405 of MoRD & as per direction of Engineer-in-Charge.

Grading No. -II (63-45mm size) with crusable screening like moorum and sand admixure

Grading No. -III (53-22.4 mm size) with crusable screening like moorum and sand admixure

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per MORD Technical Specification Clause 502 for low porosity surface and as per direction of Engineer-in-Charge.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 of MoRD & as per direction of Engineer-in-Charge.

Providing, laying and rolling of open-graded premix carpet (Cold Mix) of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using Bitumen Emulsion @ 21.5 kg/10 sqm to required line, grade and level to serve as wearing course on a previously prepared base, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of Type C as per Technical Specification Clause 508 of MoRD and as per direction of Engineer-in-Charge (Excluding cost of Seal Coat).

Providing and laying seal coat (Cold Mix) sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type C as per Technical Specification Clause 510 of MORD with S-65 grade bitumen laid by manual means and as per direction of Engineer-in-Charge.

Construction of un-reinforced, plain cement concrete pavement of 100mm thickn as per design, over a prepared sub-base, with 43 grade cement or any other type as per Clause 1501.2.2, M30 (grade) coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25mm mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the form work as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant near approaches to bridges and culverts (expansion joints), admixtures as approved, curing of concrete slabs for 14 days, curing compound and water finishing to lines and grade as per drawing and Technical Specification Clause 1501.Panels are to be made by cutting grooves of 3 to 5mm thick and 25 to 30mm deep in CC slab.The grooves are to be filled with VG-30 Bitumen with a spray of fine sand at top.

Earthwork in excavation for foundation of structures in all types of soil as per drawing and technical specification Clause 305 and 1104 of MoRD includding setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto all lead & lift, dressing of sides and bottom and back filling with excavated suitable material upto 3mt. as per direction of Engineer-in-Charge.

Providing and constructing well compacted drainage layer above the subgrade of roadwork with approved quality of dust free washed coarse to medium sand as per Clauses 5.8 and 6.6 of SP:20-2002.

Providing concrete for plain / reinforced concrete in M-15 foundation complete as per drawing and MORD technical specification Clause 800,1100,1200 and as per direction of Engineer-in-Charge.

Providing and laying reinforced cement concrete in M-25 superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5

Providing and laying of Type-B(first class) bedding for laying of Hume Pipe on well compacted moorum or approved granular material as per MORD Technical Specification clause 1105(ii) and as per direction of the Engineer-in-charge.

Supplying, fitting and placing HYSD bar reinforcement (Fe 415) complete as per drawings and MORD technical specification Clauses 1000,1200 as per direction of the Engineer in charge

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MORD technical specification Clause 1204.3.8 and as per direction of the Engineer in charge

Providing and fixing 20mm thick compressible fiber board in expansion joint complete as per drawing and technical specifications including cost convyance taxes of all materials, cost of all labours, T & P required for the work etc.complete and as per direction of the Engineer -in- charge.

Providing and laying reinforced cement concrete NP3 pipe for culverts jointing with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1100 of MoRD & as per direction of Engineer-in-Charge.

1000 mm dia Single row

1000mm dia Double row

Plain/reinforced cement concrete in M-15 sub-structure complete as per drawings and MORD technical specification Clauses 800,1200 and as per direction of the Engineer in charge

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MORD technical specification Clauses 614, 709, 1204 and as per direction of the Engineer in charge

Providing and fixing of typical masonry PMGSY informatory sign board with Logo as per MORD specifications and drawing. Brick masonry board with writting area 1.5mx0.9m and 0.115m border. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 of MoRD etc. complete and as per direction of the Engineer -in- charge.

Providing and fixing of typical PMGSY logos made of 1.6mm thick MS sheet duly stove enameled on both side with lettering and printing arrows, border etc.will be painted with ready mixed synthetic enamel paint of superior quality in required shade & colour fixed & supported on 75mmx75mmx6mmM.S.angle 3500mm long firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701 and as per direction of the Engineer -in- charge.

Providing and fixing of semi-reflectorised cautionary, mandatory and iformatory sign as per IRC-67 made of 1.5mm thick MS sheet duly stove white colour in front and gray colour on back with red reflective border of 65mm width & required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 fixed & supported on 47mmx47mmx12SWG sheet tube 3050mm long firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701.2.2 and as per direction of the Engineer -in- charge.

Providing and fixing of semi-reflectorised direction & place identification sign as per IRC-67 made of 2mm thick MS sheet duly stove white colour in front and gray colour on back with red reflective border of 70 mm width & required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 fixed & supported on 47mmx47mmx12SWG sheet tube 3050mm long duly strenghting by 25mmx5mm flat iron on edges firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701.2.2 and as per direction of the Engineer -in- charge.

Providing and fixing of typical PMGSY Citizen sign board with logo as per MORD specifications and drawing. Two MS plates of 2mm thick, top & middle plate duly welded with MS flat iron 25mmx5mm size on back on edges. The flat iron frame of both plate will be welded to 2nos 75mmx75mm of 12SWG sheet tubes posts duly embeded in C.C. M-15 grade blocks of 600mmx600mmx750mm, 750mm below ground level. The top most dimond plate will be welded to middle plate by 47mmx47mm of 12SWG steel tube. All M.S. will be stove enameled on both sides. Lettering & printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quailty in required shade & colour. All sections of framed posts & steel tubes will be painted with primer & two coats of paint as per drawing clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade Kilomitre stoneof Standard design as per IRC:8 fixing in position including painting, lettering in accordance with the specifications Clause 1703 of MoRD . etc. complete and as per direction of the Engineer -in- charge.

Fixing of 5th. Km. Stone

Fixing of Km. Stone

Fixing or 200m Stone

Guide Post (M-20)

Routine Maintenance Routine Maintenance after completion of construction works for 1st Year

Routine Maintenance after completion of construction works for 2nd Year

Routine Maintenance after completion of construction works for 3rd Year

Routine Maintenance after completion of construction works for 4th Year

Routine Maintenance after completion of construction works for 5th Year