Ordnance Factory Board Tender
Search from a pool of business opportunities related to Odisha tenders on the online platform of BidAssist. Be it an Odisha PWD tender or a civil aviation tender, one can find every tender Odisha government, as well as PSUs and other organizations, post online. Every tender, active or achieved, is sourced from the eProcurement Odisha website and thus carries full credibility.
Costs
EMD
₹ 1,03,030Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2023_MIL_144755_1Bid Award Id
ViewTender No
3012/GENL/TE-20/EO(C)/2022-23Tender Authority
Ordnance Factory Board ViewPurchaser Address
-Website
http://etenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Major repair to Security Perimeter Wall (SPW) and replacement of damaged windows and ventilator of bastions inside factory area at O F Badmal.
Remedial Measure of Safety During Execution of Work
Bidders Compliance TE-20-2022-23
BOQ Items
Fair/Straight/Racking cutting (V- groove) n exc. 10 cm width or girth on exposed surfaces of brickwork such as in splays, chamfers, etc. including rubbed finish and waste as directed by E-in-C.
3190
-
-
Dismantling of RCC structure of any description and in any position (Roofs, floors, beams, staircases, landing, chajjas and similar suspended work) and reinforcement cut as required to facilitate demolition as per direction of E-in-C
20
-
-
M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as per direction of E-in-C.
1600
-
-
M & L for RCC (nominal mix) in chajjas/beam/column etc with Type B0 1:2:4 (12.5mm graded aggregate) as per direction of E-in-C.
20
-
-
M & L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc
220
-
-
S & F of galvanised 2 strand, steel barbed wire 2.24mm dia. barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed by E-in-C (each line wire to be measured)
60
-
-
Preparation plastered or unplastered new wall surfaces and applying two coat of cement paint over a coat of primer as per the direction of E-I-C.
4061
-
-
Preparation of surfaces and writing letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high as per direction of E-I-C.
370
-
-
Taking down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frame) and removing to store as per the direction of Engineering-in-charge.
156
-
-
Taking down Chowkhats or frames exc. 1.5 sq. m but not not exc. 4 sqm each with shutters (without taking off shutters from the frame) and removing to store as per the direction of Engineering-in-charge.
156
-
-
S & F of Fe 410 -W (Gde- E- 250) quality- A, framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete as per the direction of Engineering-in-charge.
4300
-
-
S & F of aluminium windows with glass (Figured) consisting of three track channel and three sliding shutters with locking system, outside stainless steel mosquito proof net with beading and with modi guard 5 mm thick sections of size 92X32 mm for bottom, top & sides as frame sections, 40X18 mm shutter sections including neoprene gasket, nylon encased, SS rollers etc., all as specified and directed complete. Make: Jindal, Hindalco for equivalent.
330
-
-
S & F of Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified .
85
-
-
S & F of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples
65
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements