Odisha Lift Irrigation Corporation Limited Tender

200mm dia Tube well well cap

8 mm Steel Wire Rope with PVC coated

50 mm dia G.I Bend with Socket confirming to lS No.1239 (Pt‐II/1992)

50 mm dia Stainless Steel threaded nipple of 15 Cm long confirming to lS 1239 ‐ Pt‐II/1992

" U " clamp for fixing the submersible cable and wire rope with pipe

Installation of submersible pump inside the bore well fitting of HDPE pipe, tying the pump set with wire rope, connecting the supply line and submersible cable with starter, fixing the pannel board completing all the electrical installation, charging the

Empty pannel board of size ( 110cmx45 cmx25cm) made out of 20 gage CR sahet with stand made of MS angle of 20mm size with 4 nos. of legs of 30cm. Size painting in Navy Blue colour with inscription of OLIC

Earthwork in excavation of foundation in hard soil including dressing & levelling of bed within initial lead of 50mt. & lift of 1.5mtr etc complete as per the direction of the Engineer-incharge.

Filling in foundation & plinth with sand including watering & ramming etc complete as per the direction of the Engineer-incharge.

Cement concrete (1:4:8) with 4cm size h.g.b. hand broken metal of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P requir

Brick work with K.B. Brick 25cm x 12cm x 8cm size having crushing strength not less than 75kg / cm2 with dimensional tolerrance + 8% in cement mortar (1:6) in foundation & plinth etc. complete as per the Engineer-incharge.

Cement concrete (1:2:4) with 12mm size black C.B. hand broken chips of approved quality from approved quarry with ramming watering and curring etc. complete including cost, taxes, royalty convence charge of all material to worksite, supply of cement T&P r

12mm cement plaster in cement mortar (1:6) finished smooth to brick work after racking out joints including waterring and curring with cost, taxes, royalty and conveyance charges of all material to the worksite and supply of all labour and T&P required fo

Filling the foundation and plinth with excavated material as directed by the Engineer-incharge.

5.0HP/ 3.75 KW submersible BEE star rated energy efficient pump set coupled with tottally enclosed squirrel cage induction motor bearing model no. VSH-62-n/5 with bronze impeller, stainless steel shaft delivery discharge 5.00 LPS at 40mtrs. Head with cable clip, support clamp etc. suitable for operation at 415+6%,-15%, 3phase, 50HZ, AC power supply as per the particular mentioned in schedule-"A" enclosed.

Cost of Control pannel with stater sheet steel enclosure suitable for operation of squirrel cage induction motors up to 5.0HP having maximum full load current 10.0Amps. At415V+6%, 3phase, 50HZ AC supply with over load rlay range) 5.5-8.0Amps to 7.0-10.0 Amps. and no volt coil suitable for operation at voltage range of 350-440V. The control panel should provide with dependable protection against over load, single phasing and short circuit.

Writing of display board in synthetic paint as per direction of the site Enineer in Charge.

3 core 2.5 sqmm submersible Flat Cable with bunched copper conductor insulated and sheathed with PVC for submersible pump motor with voltage up to 1100volt confirming to IS 694/1990

Schedule-B

Construction of 3 phase 11 KV line as per REC standard confirming to IE Rules 1956 with 300 kg 9 M long PSC Pole with 55 Sqmm AAAC , 11 KV "V" Cross arm, with required No.of 11 KV T & C Disc. Insulators in tension point & 11 KV Pin insulators, Couping & Padding of Poles. Danger Board at each Pole, Anti Climbing Devices, Stay Set at Bending point & double stay at end point with 18 mm G.I.H.T.Stay, concreting of Stay with Anchor plate, guarding at Road crossings etc. including cost of all materials, labour transportation,inspection & commissioning etc. complete.

Construction and erection of 11 /0.4 KV , 63 KVA 11/0.4 KV (AL) BIS energy level -II Double Pole mounted Substation Star rated confirming to RE Rules 1956, mounted on 2.44 Mtr. Long structure, supported in 300 kg 9 mtr long PSC pole,transformer hard channel & top channel made of 2.8 M long 100 X 50 X 6 mm M.S.Channel, Transformer belting on 2.80 M long 50 X 50 X 5 mm M.S.Angle, (all REC SPN Std.F-3) with all accessories like 3 pole 11 KV HG Fuse(F-5)& A.B.Switches(F-9) both mounted on 2.8 M long 75 X 40 X 6 mm M.S.Channel and supported by 1.0 M long 50 X 50 X 5 mm M.S.Angle, with 3 No. 11 KV Lightening Arrestors & Distribution box for 63 KVA S/S, G.I.pipe earthing with 25X5mm G.I.Flats including cost of 63 KVA 11/0.4 K.V.Transformer , 35 Sqmm 3 1/2 Core PVC Cable - 40 mtr couping & padding of Poles, Danger board at each Pole, Anti climbing Devices & all other necessary fittings i.e required size Nuts & Bolts, Brackets, Cable, Cable Sockets, barbed fencing ( size (15'x10') with constn. of retaining wall, sand filling and metal spreading ,fixing of iron grill gate etc. as per cesu specification etc. including cost of all materials, labour , transportation complete with liasioning for testing inspection & commissioning.

Consturction of 3 Phase L.T.line as per REC standard confirming to RE rule 1956 with 300 kg 9 mtr long PSC pole support in 0.40M span with 3x35mm² +1x25 mm ² LT x LPE AB cable with coil earthing device, LT dead end clam, Suspension clamp with I hook , stay accessories such as wire insulator , clamp etc. nut bolts, alonwith concreting of poles and stay as per direction of Engineer in Charge.

Earthing with No.8 GI wire using required quantity of common salt, charcoal , GI nut bolt including digging the earth pit of size 1.2mtr. X 1.2mtr.x3mtr. And digging the wire trench and refilling after completion of earthing including supply of all