Odisha Industrial Infrastructure Development Corporation Tender

Exavaction of pipe line trench in laterite rock or any hard rock(other than granite or disintegrated rock)removed by chiselling including dressing and levelling and benching the bed not exceeding 1.50 depth & depositing the soil within intial lead of 50m & as per specification approved by the department.

Filling the pipe line trenches with sand including watering & ramming etc. complete including all labour, T&P, cost of sand, conveyance, , royalty, loading & unloading as per specification & direction of EIC.

Filling foundation trenches and Plinth with excavated & selected earth, laying in layers not exceeding 23cm thick well watered & rammed etc. complete including labour , T&P, lead & lift cost & conveyance, loading, unloading etc. complete as per specification & direction of EIC.

Providing all materials, labour, T&P for laying of centrifugally cast (Spun) Ductile Iron pressure pipes for water works purpose with socket & spigot ends confirming to IS-8329/2000 with 3rd revision in standard lengths for classification K-9 suitable for push on joints (Rubber Gasket 'D' jointing) with outside zinc coating as per IS-8329/2000 including aligning the pipes inside trench as per IS-12288/1987 including testing the pipe line with required water pressure as per IS-8329/2000 amendment 1st, Sep. 2011 etc.all complete as per specification & direction of EIC (Excluding cost for earth work, jointing of specials, rubber gasket & fittings which shall be paid separately).

500mm Dia D.I K-9 Pipe

400mm Dia D.I K-9 Pipe

250mm Dia D.I K-9 Pipe

Supplying all materials, labour and T & P for providing and laying MS pipe and specials confirming to IS 3589/99 of quality grade FE 410 of following nominal dia and including transportation of pipes and fitting to site etc. all complete as per specification and direction of Engineer-in-Charge.(MS Pipe 8 mm Thick)

500mm Dia MS Pipe

400mm Dia MS Pipe

250mm Dia MS Pipe

Providing all labour, T&P and making push-on joint with rubber gasket ring as per IS-5382/1985 1st Revision suitable for D.I pipe and fittings of the following nominal dia including testing of the joints with required water pressure (The cost is inclusive of cost of ring) and all complete as per specification & direction of E.I.C.

Material with labour (For fittings)

500mm Dia D.I K-9 Pipe

400mm Dia D.I K-9 Pipe

250mm Dia D.I K-9 Pipe

Labour only for pipes

500mm Dia D.I K-9 Pipe

400mm Dia D.I K-9 Pipe

250mm Dia D.I K-9 Pipe

Providing all materials, labour, T&P and laying in trenches following D.I fittings & fixing with the pipes after cutting the pipes to required shape & size including wastage etc. confirming to IS-9523:2000, 1st revision with pressure rating PN-1.0 of following nominal diameter, all complete including test the joints with required water pressure as per specification & direction of EIC. (Excluding cost of earth work in trenches, back filling & rubber gasket)

Considered as 2% of the cost of pipe

Providing, fitting & fixing of following size valves as per IS specifications including fixing the same with supply of required jointing materials like rubber insertion, MS nuts & bolts, paint etc. and testing the joints with required water pressure & all complete as per specification & direction of E.I.C.

500mm dia D.I Sluice valve (Non rising spindle) of PN-1.0 as per IS-14846/2000 with ISI mark.

400mm dia D.I Sluice valve (Non rising spindle) of PN-1.0 as per IS-14846/2000 with ISI mark. ( For wash out)

250mm dia D.I Sluice valve (Non rising spindle) of PN-1.0 as per IS-14846/2000 with ISI mark.

150mm dia D.I Sluice valve (Non rising spindle) of PN-1.0 as per IS-14846/2000 with ISI mark. ( For wash out)

400mm dia DI NR Valve (Make:Kirloskar/Vag/Audco)

250mm dia DI NR Valve (Make:Kirloskar/Vag/Audco)

80 mm dia D.I. Tamper Proof Kinetic air valve without Isolating SLB of PN-1.0 as per IS-14845/2000 with ISI mark.

Providing all materials, labour and T&P required for construction of RCC M-25 valve chamber of following minimum size having minimum cube strength 250Kg/cm²at 28 days confirming to IS-456/2000 and IS-3370 at all locations & heights using graded H.G. stone aggregate (crusher broken ) of 20mm & down size including machine mixing, lifting, conveying, placing in position, mechanical consolidation, curing, dewatering, if necessary, including cost for rigid, levelled & plumbed centering & shuttering to required slope, allignment & size for all kinds of RCC work with steel centering materials with all bracing, ties, anchorage & supports & removing the same after required interval from the date of casting, the minimum thickness of RCC base slab, all side walls and roof slab shall be not less than 200mm, 150mm and 125mm respectively,Providing & Placing MS reinforcement (HYSD bars) of required dia including cutting, bending, binding, straightening of approved quality as per approved design & drawing & tying the grills for RCC works & placing in position using binding wires 18 to 20 gauge soft drawn & cold annealed. PCC 1:3:6 with 40mm size h.g. stone metal (crusher broken) of 100mm thick, earth work excavation in all kinds of soil/rock including back filling duly watered & rammed as per approved design & drawing and fixing pre-cast factory made RCC man hole cover with frame of clear opening of 600mmx450mm and providing and fixing of Polypropylene Steel Reinforced Man Hole stps of approved quality and size in two parallel lines of 300mm spacing in vertical walls with center to center 375mm(staggered).Painting the chamber with 2 (two) or more coats of approved water proofing cement paint over a coat of cement wash. Printing and writing the wall sign board of approved size and specification including cost of all materials, labour, T&P, royalties, all taxes and hire & running charges of machineries with POL etc. all complete as per specification & direction of EIC.

Inner size 1500mm x 1200mm x 1500mm height valve chambers

Construction of RCC M-20 thrust block of following minimum size having minimum cube strength 200Kg/cm²at 28 days confirming to IS-456/2000 and IS-3370 at all locations & heights using graded H.G. stone aggregate (crusher broken ) of 20mm & down size including machine mixing, lifting, conveying, placing in position, mechanical consolidation, curing, dewatering, if necessary, including cost for rigid, levelled & plumbed centering & shuttering to required slope, allignment & size for all kinds of RCC work with steel centering materials with all bracing, ties, anchorage & supports & removing the same after required interval from the date of casting, Providing & Placing MS reinforcement (HYSD bars) of required dia including cutting, bending, binding, straightening of approved quality as per approved design & drawing & tying the grills for RCC works & placing in position using binding wires 18 to 20 gauge soft drawn & cold annealed, PCC 1:3:6 with 40mm size h.g. stone metal (crusher broken) of 100mm thick earth work excavation in all kinds of soil/rock including back filling duly watered & rammed as per approved design & drawing etc. all complete as per specification & direction of EIC.

RCC Thrust block of size 1000mm x 1000mm x 1000mm height

Providing all materials , labour, T&P for making flange joints with the pipes & fittings including supply of required & approved size of M.S. nuts & bolts, washer & rubber insertion & paints etc. including testing the joints with required water pressure etc. all complete as per specification & direction of EIC.

500mm size Flange joint

350mm size Flange joint

250mm size Flange joint

150mm size Flange joint

Providing all materials, labour, T&P for fixing MS flanges suitable for following dia MS pipe including cutting the pipes by oxygen and acetylene gas flames as per the required size and slope and electric welding the same with the pipes as per IS specification including cost for hire and running charges of all machine with POL. (The flanges shall be made out of following thickness plate after cutting as per required size and shape, drilling of bolt holes as per IS specification, painting the same with two or more coats of anti corrosive paint (Epoxy), the cost inclusive of hire & running charges of machineries, POL, To & Fro charges with all consumables, testing of the joints with required water pressure etc. all complete as per specification and direction of EIC.

500mm MS Flange

350mm MS Flange

250mm MS Flange

150mm MS Flange

Supply,Installation,testing and commissioning of Smart water meter suitable for following pipelines with IOT Technology using LORA or technology and related infrastructure work.

250mm dia

Provision for restoration/compensation towards damages to services lines and mending damages done to road during execution of laying pipe line and other to overcome any unfreseen items and situations including deposites to road authority and acquisition of land etc.

GST as applicable Will be Paid Extra.