Odisha Industrial Infrastructure Development Corporation Tender

Supplying, & filling in foundation and plinth with good quality river sand including watering, ramming with cost, conveyance, royalties, , of all materials and cost of all labour with T&P, sundries required for the work etc., complete (Measurement will be taken on finished compacted section) as per specification and direction of Engineer-in-charge.

Providing and laying plain cement concrete of proportion (1:4:8) in foundation and floors using cement, 4 cm. size black hard crusher broken granite stone metal, screened and washed sharp sand for mortar of approved quality from approved quarry including hoisting, lowering, laying concrete, ramming, watering and curing etc. complete to required levels laid in layers not exceeding 15 cm. thick in each layer including cost, conveyance, loading, unloading, dewatering,royalties and taxes all materials and cost all labours, sundries, T&P required for the work including shuttering , hire & running charges of concrete mixer complete as per the direction of the Engineer -in -charge.

Providing ,Lifting, Hoisting & Laying Reinforced Cement Concrete of M-20 Grade in all type of Concrete works( i.e footing, Plinth Band, Lintels, Chajja, Shelf fins, Roof slabs, Balconies, Staircase, Column, Beam Parapets, Window sills, RCC Wall, Railings etc. ) of approved designs and drawings having a minimum compressive strength ( in work test) 20 N/mm2 in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 456 and I.S. 516 using screened & washed sharp river sand for mortar and 10 mm. to 20 mm. size black hard crusher broken granite stone chips of approved quality from approved quarry, washed and cleaned to be mixed in concrete mixture with approved quality of cement including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 28 days, including cost of required steel centering and shuttering there after dismantling and removing the debrises away from the work site and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading,stacking, royalties of all materials, cost of all labours, scaffolding, sundries, T&P required for the work etc. complete in all respect but the excluding cost & conveyance of M.S. rods or Tor Steel and Binding wires and labour charges for straightening, cutting, bending etc. of M.S. rods or Tor steel and binding wires and tying the grills and placing in proper position excluding GST as directed by the Engineer-in-charge.

Footing & pedestal

Beam & Columns

Providing & fixing TOR Fe-500 reinforcement bars for RCC work of required diameter & of approved quality including straightening, cutting, bending, binding welding , joining (if necessary), tying the grills, hoisting, lowering and and placing in position as per the approved design & drawings with provision of fan hooks including cost, conveyance and taxes of reinforcement bars or tor steel and binding wires of 18 to 20 gauge and labour required for the work in all heights as per the specification & direction of E-I-C. (Linear measurements will be taken & quantity will be calculated on standard weight. Lap length of bars & weight of binding wire will not be considered for measurement.)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. All complete as per direction of EIC.

Supplying, fabricating & fixing of Structural steel items made out of channels, angles, flats, plates, chequerd plates I Section, Beam, Hollow Section any type of frame, space frame, gates, attrium in top, truss, purlins, columns, beams etc. complete as per drawing including all leads and lifts including cost of all labour, T&P etc. complete as directed by the Engineer-in-charge.

Painting two coats of synthetic enamel paint over Iron Works as per approved shade of approved quality over a coat of primer, sand papering, polishing the surface including cost, conveyance, taxes, materials, labour, T&P, scaffolding etc. as required for the work complete as per direction of Engineer-in-charge. (The paints and primer are to be approved before procurement and use)

Grassing with carpet grass(zoysia japonica) including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed. In rows 5 cm. apart in either direction as per direction of Engineer-in-Charge.

landscape irrigation system (At Archerry ground)

Supply & installation of PVC PIPE 63MMX6KG6 MTR LENGTH, ONE SIDE SOCKET,SOLVENT WELDED AS PER IS:4985-2000 including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of PVC PIPE 50MMX6KG6 MTR LENGTH, ONE SIDE SOCKET,SOLVENT WELDED AS PER IS:4985-2000 including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of PVC PIPE 40MMX6KG6 MTR LENGTH, ONE SIDE SOCKET,SOLVENT WELDED AS PER IS:4985-2000 including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of POP UP SPRINKLER PGP ULTRA,GEAR DRIVEN 10 CM POPUP,6.1-14 MTR RADIUS,.01 TO.45 LPS DISCHARGE,3/4" BSP INLET,SPECIAL PLASTIC BODY including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of AIR VACUUM RELEASE VALVE 1" BSP INLET,BODY SPECIAL PLASTIC including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of RQRC HYDRANTS 3/4" (VALVE TYPE)MADE OF BRASS including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of RQRC HYDRANT KEY 3/4" with Swivel Elbows MADE OF BRASS including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of DBL UNION TFLN SEAL PVC BALL VALVE 63MM PUSH FIT TYPE SOLVENT WELDED including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of VALVE BOX 12" MADE OF SPECIAL PLASTIC including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of VALVE BOX 10" MADE OF SPECIAL PLASTIC including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of VALVE BOX 10" MADE OF SPECIAL PLASTIC including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of Filter Station comprising of 2" outlet Media Disc Filter including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of PUMP 2.50 LPS DISCHARGE,42-58 MTR HEAD,PANEL BOARD,WIRE AND INCLUSIVE OF ALL ACCESSORIES COMPLETE including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of NON RETURN VALVE 2" PLASTIC including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & installation of Pressure Release Valve 2" including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & installing of table with ERU and pedestal having following specifications. The table shall be supplied in completely knock down conditions with an overall size 2200mm X 1800mm X 750mm that is to be assembled at site. The worktop shall have the size 2200mm X 950mm made up of 50mm thick Medium Density Fibre-board with approved laminate and finish as per approved shade. The top edge should cladded with 1.2mm thick extruded aluminium section all around the worktop and die cast end caps on joints for better strength of the table. The profile shall be in rectangle shape and enclosed by flapper box for electric provision. The top shall be supported on gable end. The end wall of the table on the side shall be topped by gable end. It should be 50mm thick Medium Density Fibre-board linear in profile and the edges cladd with extruded aluminium profile. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick particle board and shall be linear in profile. The table shall be supplied with credenza unit with an overall size 900mm X 450mmmm that shall be constructed from Pre-laminated particle board of grade II of IS 12823 with 25mm thick top and other parts 18mm thick like shutter, back, facia etc. The drawer and shutter shall be operated with ball bearing sliding channel and concealed crank hinge. G-profile Aluminium handle shall be supplied for ease of opening. The ERU unit shall be mounted on 38mm Dia. leg. Fixed pedestal shall be supplied with an overall size 380mm X 400mm X 600mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Top shall be 25mm thick, side, back, facia shall be 18mm thick. The pedestal shall have 2 nos. of drawer having same. The drawer shall be operated with ball bearing sliding channel to enable smooth operation. Aluminium handle shall be provided for ease of opening. For locking provision central lock mechanism shall be given in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on Aluminium round leg including cost of all material, labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.

Supplying & placing Back storage unit with an overall size 2250mm X 450mm X 2200mm. It should be made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade with extruded Aluminium profile. All profile i.e. side, back, shutter, shelf, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. The storage shall have shelves and 8 nos. of door shutter for ease of opening. The shutter shall be operated with concealed crank hinge and die cast handle. There shall be legs provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leatherite tapestry 1±0.2 mm thick. The understructure shall consist of pipe frame leg of SS having cross-section area 30mm X 30mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1540±10 mm(W), seat height = 420±10 mm, overall width = 1825±10 mm, overall depth = 780±10 mm & overall height = 755±10 mm. including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The structure shall be upholstered with leatherite tapestry 1±0.2 mm thick. The understructure shall consist of pipe frame leg of SS having cross-section area 30mm X 30mm. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 540±10 mm(W), seat height = 420±10 mm, overall width = 830±10 mm, overall depth = 780±10 mm & overall height = 755±10 mm.including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & placing corner table with an overall size 1200mm X 600mm X 450mm. The top of the table shall be made of 18mm thick Pre-laminated particle board of grade II of IS 12823. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The understructure shall consist of SS 202 grade pipe frame with shiny chrome finish with an overall size the size 40mm X 20mm with 1.6mm thick. One nos. footstep shall be provided between the frame with same size i.e. 40mm X 20mm. There shall be PPCP shoe provided at the bottom to avoid scratches on the floor including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing and supplying high back chair. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 50mm thick having density 45kg/m³ and the back shall be made of bright bar padded with high resilience polyurethane foam 50mm thick having density 45kg/m³. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine with contour lumbar support as well as head support. The seat and back shall be arrested together with mechanism by means of powder coated HR steel spine and armrest shall be used SS arm cladded with cushion top,completely joint with seat. For seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti shock feature.Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 40±0.5mm. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA standard. The pedestal should have five legged die casted aluminium having pitch circle dia. 700mm fitted with 5 nos. twin wheel castor. The castor of the chair should be injection moulded in black 30% glass filled nylon. The seat size shall be 510±10 mm(W) X 480±10 mm(D) and back size shall be 500±10 mm(W) X 720±10 mm(H) from seat. Overall height shall be = 1225±10 mm, base width/ depth = 760±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with the assistance of cushion. The armrest shall be of chrome plated frame padded with cushion with leatherite covering on top. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated pipe having cross section 40mm x 20mm. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 500±10 mm(W) X 500±10 mm(D) and back size shall be 490±10 mm(W) X 550±10 mm(H) from seat & overall height = 960±10 mm, overall width = 600±10 mm & overall depth = 670±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & Placing executive table with credenza and pedestal unit in completely knock down conditions with an overall size 1950mm X 1750mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall have the size 1950mm X 850mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form edges and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. Credenza unit shall be supplied for storage purpose with an overall size 900mm X 450mm X 750mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 nos. of shutter operated with the assistance of sliding rail track and SS handle and Multi-purpose (MP) locking mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380 including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying and placing ergonomically designed, comfortable & aesthetically appealing High back chair. The seat shall be made of 18mm thick hot pressed plywood with HR polyurethane foam 40mm thick having density 40kg/m³ upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 GSM and the back shall be made of hot pressed plywood 15mm thick with HR polyurethane foam 12mm thick having density 23kg/m³ upholstered with leatherite tapestry in tan colour with 0.8mm thick and 535 GSM. Headrest shall be provided for comfort of head with leatherite tapestry. The armrest shall be used PP arm completely joint with seat and back. The chair shall have torsion bar revolving mechanism with single position locking and tilt tension adjustment. The pneumatic seat height adjustable 80mm with BIFMA standard class-3 gaslift. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 650 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMA standards. The Seat size shall be 500±10 mm(W)X500±10 mm(D) and back size shall be 720±10 mm(H) from seat & overall height = 1135±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & Placing Visitor Chair ergonomically designed for user comfort & shall have asthetically appealing design. The seat shall be made of 18mm thick hot pressed plywood with HR polyurethane foam 40mm thick having density 40kg/m³ upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 GSM and the back shall be made of hot pressed plywood 15mm thick with HR polyurethane foam 12mm thick having density 23kg/m³ upholstered with leatherite tapestry in tan colour with 0.8mm thick and 535 GSM. The armrest shall be used PP arm completely joint with seat and back. The frame structure shall be cantilever support type made up of MS CRCA chrome plated pipe of size 30mmX15 with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor . The Seat size shall be 500±10 mm(W)X510±10 mm(D) and back size shall be 550±10 mm(H) from seat & overall height = 985±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & placing storage unit with an overall size 900mm X 450mm X 2000mm. Storage shall be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. All profile i.e. side, back, top, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 3 nos. of adjustable shelf and 1 fixed shelf. 2 normal shutter and 2 glass shutter shall be provided for closing and opening the shutter. The glass shutter shall be made 4mm clear glass insert within aluminium profile. The shutter shall be operated with concealed crank hinge with SS handle as well as MP lock mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the base to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380 including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & Placing Conference table in completely knock down conditions with an overall size 2400mm X 1800mm X 750mm that is to be assembled at site. The construction of the main table shall be with minifix dowels, pins and MS brackets. The top shall be made up of 25mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in C shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and the profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like I0SO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380 including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 18mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (40+40)mm thick having density (40 & 32)kg/m³ in seat and (30+30)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 1mm thick and 571 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support as well as head support. The chair shall be supplied with polypropylene arm with cushion base leatherite covering top. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS CRCA powder coated with 50-60µ DFT thick having pitch circle dia. 660 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 500±10 mm(D) X 520±10 mm(W) and back size shall be 520±10 mm(W) X 700±10 mm(H) from seat. Overall height shall be = 1160±10 mm, overall depth = 680±10 mm & overall width = 660±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & Placing executive table in completely knock down conditions with an overall size 1200mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. Mobile pedestal shall be provided with an overall size 400mm X 450mm X 650mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Pre-laminated particle board and mounted on nylon castors. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380 including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying and placing single bed with an overall size 2060mm (L) x 1131 (B) x 930mm (H). Head and tail panel shall be made of 18mm thick Pre laminated particle board and baton shall be made of 32mm thcik MDF board duly bull nose shape. Sides baton shall be made of 32mm thick MDF board (one side full round post forming) and 18mm thick particle board with 2mm thick PVC edge banding . The edge banding shall be pasted with hot melt glue at 200 degree Celsius. Mattress panel shall be made of 18 mm thick particle board. The understructure shall consist of MS channles in 1mmm thickness. Horizontal and Bottom Plinth shall be made of 25mm thick Pre laminated particle board. including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & placing storage unit with an overall size 900mm X 450mm X 2100mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. All profile i.e. side, back, top, shutter, shelf, skirting shall be 18mm thick. The edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have four fixed shelf. 2 nos. of door shutters shall be provided for opening and closing the storage operated with concealed crank hinge and SS handle. There shall be buffers provided at the bottom to avoid scratches on the floor. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380 including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & Placing visitor chair. The seat and back shall be made of double layered (15+6)mm thick hot pressed commercial plywood padded with high resilience polyurethane foam having density 40kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The chair shall be supplied with cushion arm with leatherite mounted on metal pipe frame. The frame structure shall be cantilever support type made up of MS CRCA chrome plated tubular pipe having cross-section area 40mm X 20mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 490±10 mm(D) X 515±10 mm(W) and back size shall be 520±10 mm(W) X 530±10 mm(H) from seat. Overall height shall be = 950±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & Installation ofSinlge Mattress, Size-78" X 36" including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supplying & Placing executive table in completely knock down conditions with an overall size 2000mm X 1880mm X 750mm that is to be assembled at site. The work top shall have the combination of 18mm PLPB and 25mm MDF board. The worktop shall have the size 2000mm X 980mm made up of 18mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The base top shall be made up of 25mm thick Medium density fibre-board with deco painted. The top profile shall be in rectangle shape with front half round shape and particle board edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius and MDF board having half round post form with grooves. The top shall be supported on MS powder coated U-clamp. The end wall of the table on the side shall be topped by gable end. It should be 36mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thick particle board in linear shape with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The side top shall be provided with an overall size 900mm X 450mm X 750mm. It should have the combination of 18mm PLPB and 25mm MDF board. Side top shall be supported on Peg which mounted over side storage unit. The side storage unit having an overall size 850mm X 400mm X 645mm. The side unit shall be made up of particle board of grade II of IS 12823 with base 9mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 3 nos. of drawer having same size and 1 nos. of shutter. The drawer shall be operated with handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The shutter shall be operated by handle and concealed crank hinge. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A pedestal shall be provided with an overall size 400mm X 450mm X 645mm. The pedestal shall be made up of particle board. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with handle and easily close & open with the assistance of sliding channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380 including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 485±10 mm(W) X 450±10 mm(D) and back size shall be 490±10 mm(W) X 610±10 mm(H) from seat. Seat height 460±10 mm, overall height shall be 1060±10 mm, overall depth = 620±10 mm and overall width (Arm) = 600±10 mm, Overall base dia. 760±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. The frame structure shall be cantilever support type made up of MS/CRCA powder coated with 50-60µ (DFT) thick round pipe of dia. 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 480±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 400±10 mm(H) from seat & overall height = 820±10 mm including cost of all material,labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & Installation of Basic Bed With Flat Plateform, MS Head & Foot Panel, Powder Coated, Plain bed uniformly perforated, Size 6x3ft ,Urine hooks below the bed on either sides,I.V. position at all the four corners of the Bed.Overall Dimension - 1800mm X 900mm X 510mm including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & Installation of Bed Side Locker General, Stainless Steel Top, Powder Coated, Machine pressed sheet box with door of heavy gauge,Assembled to CRC tubular legs of 2.5cms dia.,Stainless steel polished top With three side Rails,Mounted on protective PVC Stumps,Pre-treated and epoxy powder coated Overall Dimension - 400mm X 400mm x 820mm including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & Installation of Bed Side Stool, Top plate made of MS CRCA sheet with section of thickness 1 ± 0.2mm & non corrosive. It has a square of 300± 10mmmm, seat base made of MS rectangular tube. The under-structure consist of 4 legs made up of MS ERW tube of diameter 25.4 mm x 25.4 mm and 1.2mm thick. The press formed pipe leg give a round & clean look. All the legs is Provided with 4 nos of Nylon bush. All metal components are pre treated with zinc phosphating in 7 tank process and then powder coated with epoxy polyester powder coating ., Overall Dimension - 300mm X 300mm x 510mm including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & Installation of Revolving Stool, Overall Dimension: Overall Sizes Diagonal Leg Dia 538 mm H510 min-690max. Top plate made of SS 304 made sheet with spin section of thickness 1mm & non corrosive. It has a diameter of 305mm, seat base made of MS ring and rectangular tube. EN8 Screw having dia of 22 mm is used for height adjustment of the seat base. The round hub made of MS ERW tube having dia of 38mm and thickness 2 mm. The Hub is welded with the legs and it accommodate and cover the lead screw mechanism. The under-structure consist of 4 legs made up of MS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leg give a round & clean look. All the legs is Provided with 4 nos of Nylon-6 bush. All metal components are pre treated with zinc phosphating in 7 tank process and then powder coated with epoxy polyester powder coating . Safe working load is 135kg. Company should be ISO-9001, 14001, 45001, 50001, BIFMA, AIOTA and Greenguard certified. European CE certificate should be provided from Notifying body with 4 digit registration code. The bidder should be UFDA registered. The following test reports along with the bid which should be taken from NABL certified lab:1) ISO certificate should be taken from NABCB approved lab. 2) The bidder should having Central Drugs Standard Control Organization registration. including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Supply & Installation of Saline Stand, Height Adjustable, Stainless Steel Frame, SS Base ,Stainless Steel tubular pipe,Double hook S.S. adjustable IV rod with a Bakelite knob,Five-legged SS base mounted on 10 cms castors including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing, supplying and placing steel almirah in perfectly upright and straight position. The overall size of the almirah shall be 900mm (W) X 450mm (D) X 1830mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. All components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf & door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 40-60µ. including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

Providing and supplying four seater café table with PP shell seating system. The overall size of the table shall be 1200mm X 1660mm X 700mm. The table shall be supplied in completely knock down condition. The main top of the table shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved decorative shade with an overall size 1200mm X 600mm. The profile of the table top shall be rectangle shape and the edges sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on 4mm thick hinges mounted on rounded bent pipe having Dia. 48mm with 1.6mm thick that shall be joint with rectangle beam having cross-section area 60mm X 40mm with 1.6mm thick. The seat shall be made up of one piece injection moulded polypropylene shell mounted on 50mm Dia. round pipe (welded together with rectangle beam) with 1.6mm thick with the assistance of 8mm thick solid HR steel plate. The seat shall be 260mm differ to each other. The complete understructure shall be made up of MS CRCA pipes with 50-60µ thick powder coated. The base shall be covered with plastic caps. The seat size shall be 440±10 mm(W) X 440±10 mm(D) and back size shall be 400±10 mm(W) X 290±10 mm(H), overall height shall be 680±10 mm. including cost of all labour, T&P etc. as required for the work complete as directed by the Engineer-in-charge

N.B: GST as applicable will be paid extra. For Furniture items intrested bidders can collect the 3d images of samples approved by client department from IDCO office before submission of bid. 2) samples of furnitures shall be approved/finalized by client/EIC before procurement to site