Odisha Hydro Power Corporation Limited Tender
Search from a pool of business opportunities related to Odisha tenders on the online platform of BidAssist. Be it an Odisha PWD tender or a civil aviation tender, one can find every tender Odisha government, as well as PSUs and other organizations, post online. Every tender, active or achieved, is sourced from the eProcurement Odisha website and thus carries full credibility.
Costs
EMD
₹ 19,660Document Cost
₹ 6,000Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_OHPCL_100304_1Bid Award Id
ViewTender No
RHEP-TCN-NO-49/2023-24Tender Authority
Odisha Hydro Power Corporation Limited ViewPurchaser Address
-Website
http://http://ohpcltd.com/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
B. EXPANSION JOINT
Surface preparation by mechanically dismantling the upper surface of the concrete minimum upto 45 mm from the top as it is soaked with spealage of oil from the transformer.
110
1590
174900
... More
Thereafter the concrete shall be repaired with epoxy mortar Nitomotar EP 75 properly primed with Nitoprime 25 and to provide good shape for adhesion for further work for expansion joint treatment.
110
1291
142010
... More
The surface to be manually leveled so that the surface to be smoothed using iron brush and chisel. The surface to be leveled with leveling tape. There after one coat of MYK Indubond VK4031 shall be applied over both the surface of the expansion joints. After priming MYK Flexi Joint TPE 150 mm X 1mm shall be pasted over the prepared area.
110
3387
372570
... More
C. PRESSURE GROUTING
Injection grouting using non-shrink grout additive of Cebex 100 with neat cement slurry by drilling the hole of 12mm dia. and fixing the nozzles using fast setting compound Renderoc plug to the depth of 50mm along the construction joints at a distance of not more than 300mm c/c.
500
230
115000
... More
Providing pressure to the prefixed nozzles in the concrete admixed with cement additive Cebex 100 till saturation.
2000
222
444000
... More
D. WATERPROOFING FROM NEGATIVE SIDE
Thereafter the surface shall be applied with two coats of crystaline based waterproofing system XYPEX CONCENTRATE having 7 bar capacity to seal any voids to the surface.
250
1276
319000
... More
E.TILE WORK
Dismantling of existing tiles both on floor and wall by mechanical hammering and dispositing those to a distance of 50 mtr.
60
108
6480
... More
Supply and fixing of tiles both on Wall and Floor after repair with proper adhesion.
60
1121
67260
... More
F. SPALLING TREATMENT
Preparation of the surface by mechanical abrading to remove all loose & dead mortar, laitance, oil, grease, etc. and washing those with plenty of water. The rate to be inclusive of scaffolding, labour, equipment hire charges etc. all complete. (measurement will be taken on roof area basis)
50
70
3500
... More
After the surface preparation if it is found that the reinforcements have been corrosed more than 40 % that portion should be cut down and replaced with newer ones. After fixing the newer reinforcements it will be applied with two coats of anti-corrosion zink rich epoxy primer Nitozink primer @ 80microns. the film shall be continuous especially in the regions where pitting imperfections etc. are present on the surface of the bars.
50
260
13000
... More
After the reinforcement part is over, solvent free epoxy bonding agent Nitobond EP will be applied over the old concrete including the reinforcement for joining old and new concrete.
50
540
27000
... More
Replastering of the exteriors with polymer modified 1:3 Cement mortar containing a modified styrene butadiene emulsion Nitobond SBR of Fosroc chemicals (I) Pvt. Ltd., specially designed for use as a bonding aid and gauging liquid for cementitious systems and tested in accordance with SB 6319. The dosage could be 3lts./ per bag of cement.
70
360
25200
... More
Supply and fixing of 3mm thick protective fibre/ Neoprene sheets on the expansion joints.
45
500
22500
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements