Odisha Hydro Power Corporation Limited Tender

Dismantling G.C.I. and A.C. Sheet roofing after carefully removing the bolts and nuts including stacking the useful materials for reuse and removing the debries within 50m lead.

Filling in foundatin and plinth with sand watered and rammed including cost of materials, transportation, and placing as per direction of EIC

Cement concrete (1:3:6) with 4cm size Crusher broken granite metal per one cum. including cost of materials, transportation, and placing as per direction of EIC

Cement concrete (1:2:4)with 12mm size Crusher broken granite chips per 1cum including cost of materials, transportation, and placing as per direction of EIC

Rigid and smooth centering and shuttering for RCC works including false work. Etc., complete including hoisting and laying materials, transportation, and placing as per direction of EIC

Supplying, fitting and placing uncoated of SAIL TMT BAR reinforcement complete as per drawing and specification including hoisting and laying materials, transportation, and placing as per direction of EIC

Supply and fixing of M.S. angles (75x75x6mm) as and where required for use as purlins and including transportation, Labour, hoisting and placing in position to site as per direction of EIC.

Supplying, fitting & fixing 0.5mm TCT TATA blue scope sheet, 550Mpa yield strength mix anticorrosive steel with plain formed ridges, gutters, flashing etc.(as same materials as above) having total girth upto 600mm and standard length of 6000mm as required and quoted with hot dip zinc alloy of 120 gms per sqm mass of coating (total both sides) as per IS 277 and finished with polyster coating (EPG 10) of 18-20 microns in approved colour over primer coat of 5 microns on top and 5-7 microns of service coat in grey colour over primer on back, having KLT CRIL HISPAN profile of overall width of 1100mm, with five crests of 35+1mm spaced at 250+2 mm centers and with three small corrrugations of 8mm depth continously spread over 55mm width each valley of the sheet on steel structures complete with necesssary self drilling and self trapping screws/bolts and nuts, neoprine and limplet washers with 150mm end laps wherever required. Measurement shall be made on "as laid" area . Sheets shall be supported with coil manufacture's test certificate for strength. The rate shall include alll costs towards materials transport, storage, handling, liftinig , positioning, fixing and all labour and complete as per direction of EIC.

C.B Brick (23x11x8cm) size having crushing strength not less than 35kg/ cm2 with cement mortar (1:6) in foundation and plinth per cum including hoisting and laying materials, transportation, and placing as per direction of EIC

12mm thick cement plaster (1:4) for repair work over brick work including cost of all materials, labours, royality, taxes and duties etc. as per direction of EIC

16 mm. thick cement plaster (1 :6) over brick or stone masonry per 1Sqm including cost of all materials, labours, royality, taxes and duties etc. as per direction of EIC

Priming 1 coat with any appproved Primer (Asian/Berger) on plastered surface including cost of materials, labour, transportation etc. & complete as per direction of EIC.

Wall painting two coat with plastic emulsion paint of approved shed (Asian/Berger) on old work to give an even shed including cost of materials, labour, transportation etc. & complete as per direction of EIC.

Painting two coats with weather seal paint over a coat of primer including cost, conveyance all materilas, labour and T & P etc complete.

Supply and fixing of MS panelled Doors Double leaved shutter with MS frame of size 1900mmx900 mm made out of Ms Angle/ CR sheet, Outer Frame MS Angle 35x35x5 mm Inner frame for leaf-MS Angle- 25x25x3 mm with 0.8/1.00 mm CR sheet and 18x5 MS flat support with fabricated Aldrops and Tower bolt including all labour charges & transpotation & complete as per direction of EIC

Supply and fixing of MS panelled window double leaved shutter with MS frame and grill of size 1200mmx900 mm made out of of Ms Angle/ CR sheet, Outer Frame MS Angle 35x35x5 mm with 10mm square bar net Inner frame for leaf-MS Angle- 25x25x3 mm with 0.8/1.00 mm CR sheet and 18x5 MS flat support with fabricated Aldrops and Tower bolt including all labour charges & transpotation & complete as per direction of EICtranspotation & complete as per direction of EIC