Odisha Hydro Power Corporation Limited Tender

12 mm thick C.P. (1:6) over brick masonary including cost conveyance royalities, taxes of all materials.

Cement concrete (1:2:4) to M 15 using 12 mm grade hard granite chips including lowering, laying concrete, watering and curing to required time etc. including cost, conveyance, royalties, taxes of all materials, cost of all labour with T & P required for the work etc. complete as per direction of Engineer-in-charge.

Providing and laying water proofs with polymeric bituminous membrane (Plastic felt) of 2.25Kg/Sqm and 2mm thickness consisting of layers having center core of 20 microns thermoplastic high molecular high density polyethylene H.M.H.D.P.E. film of grade 2504 including priming the surface with bituminous primer @ 0.3 Kg/Sqm providing a coat of hot blown bitumen of 1.32 kg / Sqm, applying and laying plastic felt membrane with 10 c.m overlap adhered to blown bitumen of 85/25 or 90/15 grade and covered with a layer of hot blown bitumen @ 1.2Kg/Sqm etc complete as per direction of Engineer-in-charge.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing.

Providing & laying two coats of synthetic enamel paint on (wood) surface over one coat with any approved primer including cost of primer of approved shade after necessary preparation of surface by spray painting in all floors of conveyance of all complete including supply of all labour, materials, T&P, taxes etc. complete.

Scraping old paint with scrappers, sand papering and washing with soap water or soda including scaffolding charges up to 5m. height. (S/R-2006, P.105, It.12)

Priming one coat to walls with appd. Primer including cost of primer

Wall painting 2 coats with plastic emulsion paint of approved shade on new work over a coat of oil bound primer to give an even shade as per direction of Engineer-in-charge.

Finishing wall surface of walls with Acrylic wall putty (water based) as per direction of Engineer-in-charge.

Exterior wall painting with two coats of weather coats over a coat of oil bound primer including cost of weather coat as per direction of Engineer-in-charge.

Supplying all materials, labour, T&P and fitting and fixing U-PVC rainwater pipes and fittings to walls with nails, bobbins and wooden plugs as per specification and direction of the engineer in charge

Supplying, fitting, fixing 30 cm x 30 cm / 40 x 40 cm spl. plain/ printed series ceramic floor tile of premium grade having thickness 7 mm to 8 mm with 20 mm thick c.m. (1:4) including cost of all materials

Supply, fitting, fixing of over head watertank cover for 1000 ltr Sintex tank

Supplying, fitting, fixing up window (sliding type) made up powder coated aluminum Section 9778, as windows frame section No. 4095, 4096 and 9777, 3994 as shutter frame with 5mm thick plain glass as panel fitted with rubber beading including locking arrangement including all fitting including cost of materials all taxes labour, T&P etc. complete as per direction of Engineer-incharge

door & window Tower bold- 150mm x 10mm

door & window Aldrop - 250mm x 16 mm

door & window Hinge

W.I. Clamps

Painting two coats with approved enamel paint on new wood/steel work (Labour +Material) for ground floor

Supply and fitting of taps, pipes, bends, short piece, Tee, door bends etc.

Brick work with K.B. bricks having crushing strength not less than 75 kg/Sq.cm. in cement mortar (1:6) in foundation and plinth.

Providing and fixing CP Bib cock of 15mm dia nominal bore of Hindware cat No. F200003FT or euivalent make as per direction of Engineer-in-charge.

Providing and fixing CP angle cock of 15mm dia nominal bore of Hindware cat No. F200005FT or euivalent make as per direction of Engineer-in-charge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required.

Structural steel work riveted, bolted or welded in built up sections , trusses and frmaned work including cutting hoisting fixing in position all complete.

Fencing with R.C.C. post placed at required distance, embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post one side only, provided with horizontal lines and two diagonals of barbed wire weighing 9.38 kg per 100 metres (minimum), between the two posts fitted and fixed with G.I. staples on wooden plugs or G.I. binding wire tied to 6 mm bar nibs fixed while casting the post (cost of R.C.C. posts, struts, earth work and concrete to be paid for separately) :- Payment to be made per metre cost of total length of barbed wire used. Barbed wire

Supply, fitting, fixing of TATA blue scope corrugated sheets(0.4 mm thick) with L-hook, linkpit washer etc. complete. Including cost of all materials, labour, T&P, taxes etc. complete. (A/R 2006 P.125 Ietm-32).

Supplying at site : R.C.C. Standards post/ struts/rails/ pales of mix 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 12.5 mm nominal size) with wooden plugs or 6mm bar nibs wherever required as per direction of Engineer-in- charge (cost of earth works in excavation, concrete works in foundation to be paid separately).

Providing and fixing of 8mm thick poly carbonate sheet roofing up to any pitch including fixing with polymer coated J or L hooks bolts and nuts 8mm dia G.I plain /Bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. the sheets shall be manufactured out of poly carbonate sheet and polymer with Ultra -Violet stabiliser in resin system under approximately 2400 psi and hot cured,. they shall be of uniform pigmentation and thickness with out air pockets and shall conform to IS 14443: 1997 , the sheets shall be clear or pigmented, textured or smooth as specified. complete as per direction of Engineer in charge. (measurement done on Sq.m all materials and labour supplied by the agency.)

Drainage repair :- Filling in Foundation and plinth with sand watered and rammed (Labour & material)

Drainage repair:- Cement concrete (1:4:8) with 4cm size hard granite metal including the cost, conveyance, royalty, all other taxes and labour charges etc.Complete.

Drainage repair:- Cement punning per Sqm.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete,

Dismantling and removing i.e. cement concrete including stacking the useful materials for reuse and removing the debris away from work site with all leads and lifts as per direction of Engineer-in-charge.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately PiaSal wood

Supplying all materials, labour, T&P and fitting and fixing U-PVC SWR soil waste ventilating pipes and fittings to walls with nails, bobbins and wooden plugs or laying in trenches including earthwork in excavation in all kinds of soil and refilling of trenches as per specification and direction of the engineer in charge