Odisha Construction Corporation Limited Tender

01 no 350 Amp FP on load change over switch

01 no 350 Amp FP MCCB (25/36 KA)

1 set 400 Amp TPN Cu Bus.

Outgoing

02 nos 63 Amp FP MCCB (25 KA)

02 nos 32 Amp FP MCCB (25 KA)

03 nos 200 Amp FP MCCB (25 KA)

Instrument - 1 set of phase indicating lamp with control fuses, Voltmeter, ammiter with selector switch, and CT etc.

Supply, delivery of L.T outdoor with slanting roof floor mounted type distribution boards made out of 2mm thick CRCA sheet metal, cubical fixed on m.s. angel frame work, duly acid treated for derusting, premiered and painted with 2 coats of enamel paints of approved shade: IP-52 class of protection, having hinged door having provision for cable/conduit entry and earthing studs, as per specification mentioned below duly factory wired conforming to the relevant ISS and as per special conditions of contract making good the damages caused complete as per the direction of Enginner-in-Charge.(Sub distrubution board)

Incoming

01 no 200 Amp FP on load change over switch

1 set 250 Amp TPN Cu Bus.

Outgoing

08 nos 32 Amp FP MCCB (25 KA)

Instrument- 1 set of phase indcating lamp with controls fuses, Voltmeter. Ammeter with selector switch, and C.T. etc.

Supply, delivery of reversing starter in a slanting roof enclosure for the 11 K.W induction motor with single phase preventer and over load relay and as per the direction of Engineer-in-Charge

Supply, delivery of following size of PVC insulated, PV sheathead, GI round / strip armoured stranded conductor power cable of 1100 volt grade conforming to IS:1554/1978 amended upto date, laid directly in ground /on the cable tray excluding the cost of trays/including the cost of excavation of earth in all kinds of soil and rock, sand cushioning, protective brick covering in 8 bricks per meter fashion, refilling the trench with excavated soil free from rock and sharp edges but including the cost of cable end termination complete with making good the damages caused as required and as per direction of Engineer-in-Charge

(A) 3.5 C 150 Sqmm PVC A PVC

(B) 3.5 C 35 Sqmm PVC A PVC

( C ) 3.5 C 95 Sqmm PVC A PVC

(D) 4 C 6 Sqmm PVC A PVC

(E ) 4 C 6 Sqmmflexible Cu cable

(F) 3 C 6 Sqmm flexible Cu cable

(G) 10 Sqmm Cu multicore cable

(H) 6 Sqmm Cu multicore cable

(I) 4 Sqmm Cu multicore cable

Supply, delivery of 25 X 3 mm GI flat for earthing of equipment and pannels including making and termination required complete as the direction of Engineer-in-Charge

Supply of materials, delivery of GI cable tray (ladder type) for laying of cable to provide power supply for hoist and gantry side, made out of G I as per direction of Engineer-in-Charge

Supply, delivery of 3 mtr. Long copper earthing electrode 50 mm dia MTB PC earthing device conforming to IS:3043, digging earth pits and filling with chemical compound (Earth resistance improvement compound) and making earth chamber as per direction of Engineer-in-Charge

Supply of materials, providing of 100 mm GI pipe with bend for pier lower position to upper part pier position top as per direction of Engineer-in-Charge

Supply, delivery of switch sockets, which shall be of heavy duty industrial type rated for 415V. 50Hz, 63 Amps and suitable for structure mounted in outdoor exposed to seen in an environment of 100% huminity. The interloking arrangement shall be such that it is not possible to insert on withdraw the plug with the switch in "ON" position. The enclosure shall be of cast alluminium alloy 4600 as per BIS :617. The enclosure shall have looping -in and looping- out faclilities for power cables of 3.5 C 35 Sqmm PVC A PVCcable and complete with 2 nos. double compression cable glands. Those socket outlets shall be located in the lower part of the encloser and shall be provided with a threaded aluminium cover attached to the body with GI chain. The sockets shall be sunk will and maintain satisfactory presure with the plug. The sockets shall have four contacts i.e. three for phases and one for earthing. Two nos. external earthing terminals shall be provided. The plugs shall be such that they can be easily fitted into the socket outlets knurled knob arrangement for screwing on the body of the socket and as per direction of Engineer-in-Charge

Supply of materials of 8 SWG GI wire, accompanied through cable and should be connected to earthing points as required and as per the direction of Engineer-in-Charge

A) Supply of materials, delivery of ABC stored pressured fire extinguisher (5Kg) and buckets with stand and all accessories as per the direction of Engineer-in-Charge

B) Supply and delivery of insulated chequered mat (4 X 1mtr) as per the direction of Engineer-in-Charge

Supply,delivery of limit switches shall be rated as 25 AMP at 440Volt AC, 50Hz and of direct position action type (position indicator) and as per direction of Engineer-in-Charge.

Supply, delivery of 2 X 100W LED street light fixture with all acessories including power factor improvement condenser and making connection including 7M long tubular /hexagonal G.I pole fixed on the top of the barrage and flexible cable for J.B including 6 AMP SP MCB to the fixture at the top of the pole as required as per the direction of Engineer-in-Charge.

Charges for erection, Installation, commissioning & testing of item No. Sl. No. 1.01 to 1.38