National Institute Of Technology Tender

Providing and placing reinforcement for R.C.C. work including straightining cutting bending placing in position and binding allcomplete. Upto plinth level and above plinth level Thermo Mechanically Treated Bars

Half brick masonry with Flyash cement bricks of class designation 75 in superstructure and above plinth level upto V th floorlevel in Cement mortar 1:4 (1 cement: 4 sand) complete in all respect as per direction of Engineer in charge

Providing and fixing of ISI marked flush door shutters conforming to IS 2202 (Part-I) Non-decorative type , core block board construction with frame of 1st class hard wood and well matched teak 3ply veenering with vertical grains or cross bands and face veneers on both faces of shutters 30mm thick includig ISI marked stainless steel butt hinges with necessary screws.

Providing and fixing to existing door frames 24mm thick factory made PVC door shutter made of styles and rails of a UPVC hollow section of size 59x24mm and thickness 2mm +/-0.2mm with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S galvanised /plastic brackets of size 75x220 mm having wall thick ness 1.0mm and stainless steel screws. the styles of the shutter reinforced by inserting galvanised M.S tube of size 20x20mm and 1mm +/- 0.1mm wall thickness. the lock rail made up of H section, a UPVC hollow section of size 100x24mm and 2mm+/- 0.2mm wall thickness fixed to the shutter styles by means of plastic / galvanised M.S U cleats. the shutter frame filled with a UPVC multichambered single panel of size not less than 620mm , having over all thickness of 20mm and 1mm +/- 0.1mm wall thickness. the panels filled vertically and tie bar at two places by inserting horizontally 6mm galvanised M.S rod and fastened with nuts and washers complete as per manufactur's specification and direction of Engineer in Charge. (For WC and bathroom door shutter)

Steel work welded in built upsection/ framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer using structural steel etc as required below in grating frames guard bar ladder railings brackets gates and similar works. in grating , frames guard bar railing brackets gates and similar works

Providing and laying Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS 15622 of approved make in all colours shade laid on 20mm thick cement mortar 1:4 (1 cement : 4 sand) including pointing the joints with white cement and matching pigment etc complete. Sizes of Tile 60x60xCm

Providing and fixing at all heightfalse ceiling including providing and fixing of frame work mae of special sections power pressed from M.S sheet and galvanised in accordance with zinc coating of grade 350 as per IS 277and consisting of angle cleats of size 25mm widex1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener12.5mm dia x40mm long with 6mm bolts to the angle hangerof 25x25x0.55mm of required length, and other end of angle hanger being fixed withnut and bolts to G.I channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a directionperpendicular to G.I channel with connecting clips made out of 2.64mm dia 130mm long G.I wire at every junction including fixing the gypsum board with ceiling section and perimeter channels of 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to walls/ partition with the help of rawl plug at 450mm centre to centre with 25mm long drive all screw @230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufacturer specification and also including the cost of making opening for light fittings and grills, diffusers, cutouts made of frame of perimeter channels suitably fixed all complete as per drawing and specification and diretion of Engineer in Charge but excluding the cost of painting with: 12.54mm thick tapered edge gypsum board conforming to IS 2095-Part-I

20mm cement plaster of mix 1:6 (1 cement: 6 Sand)

Providing and finishing wall surface with acrylic wall care putty (water based) of approved make (Birla or Equivalent) and finished smooth and even surface to receive painting including cost of scaffolding staging charges with all cost of materials taxes labour T&P etc complete

Distempering with 1st quality acrylic distemper (readymade) of approved manufacture and of required shade and colour complete, as per manufacturer's specification. New Work( Two or more coats )

Applying one coat of cement primer of approved brand and manufactureron wall surface. Cement primer

Renewing glass panes with Putty and nails wherever necessary: Float glass panes of thickness 4mm

Providing and fixing of wash basin with C.I brackets, 15mm Cp brass pillar taps 32mm Cpbrass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls whereever require: including clamps and fixtures complete as per direction of Engineer in charge White vitreous china wash basin size 630x450mm withsingle 15mm CP Brass

Providing and fixing of chlorinated polyvinyl chloride (CPVC)pipes , having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes fittings with one CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge(Internal work exposed on Wall) (ASTRAL/ FINOLEX/equivalent) 25mm nominal bore

Supplying and fixing and fittins of uPVC pipes of approved brand (Astral/Finolex/Supreme) 2.5Kg/Sq.Cm complete with fittings including cutting and making good the walls etc. as per direction of Engineerin Charge. 110mm dia Pipes

Providing and laying APP (Atactic polypropylene polymer) modified prefabricated five layer minimum 3mm thick waterproofing membrane , mineral top finished reiforced with non-oven polyster matt manufactured by Bitumat co. Ltd, Suprema general membranes ,Tamko,Sika India pvt ltd ,STP ltd,Hydrotech ltd,Dr. fixit , prodorite ltd or equivalent, consisting of a coat of bitumen primer for bitumen membrane @ 0.40 ltr /Sqm by the same membrane manufacture of density at 25°C , 0.87-0.89 kg/ltr and viscosity 70-160 cps. over the prime coat , the layer of membrane shall be laid using Butane torch and sealing all joints etc and preparing the surface by filling undulations with cement mortar (1:6) and curing the surface complete in all respect ( to be paid separately ) and as per direction of Eng-in-charge.

Providing and fixing aluminium work half glazed with 5.0mm thick glass pane and half poanelled with prelaminated particle board (Nova board/ equivalent) as per IS 12823 grade 1 type II in panelling for doors and windows ventilators and partitions with extruded builtup standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plug and screw or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at jinction at top and bottom and sides with required PVC /neoprene fillet etc aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angles , Aluminium snap beading for glazing /panelling CP brass /stainless steel screws all complete as per architectural drawings and direction of Engineer in Charge (all fittings such as hinges handle and beading etc all are included and measured in Sq.M) (Fixed Section: Top/Bottom: 63.5x38.1x1.5@0.861kg/mtr Middle double groove: 63.5x38.1x1.53@0.942kg/m /// Door frame: 101x44.45x1.60@1.301Kg/mtr) For Fixed portion only

Providing and fixing aluminium work half glazed with 5.0mm thick glass pane and half poanelled with prelaminated particle board (Nova board) as per IS 12823 grade 1 type II in panelling for doors and windows ventilators and partitions with extruded builtup standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plug and screw or with fixing clips or with expansion holdfasteners including necessary filling up of gaps at jinction at top and bottom and sides with required PVC /neoprene fillet etc aluminium sections shall be smooth rust free straight mitred and jointed mechanically wherever required including cleat angles , Aluminium snap beading for glazing /panelling CP brass /stainless steel screws all complete as per architectural drawings and direction of Engineer in Charge (all fittings such as hinges handle and beading etc all are included and measured in Sq.M) ((((DOOR : V:85x44.45x1.8@1.301 kg/mt, Top: 114.30x44.45x1.35@1.139Kg/mt, Bottom 114.30x44.45x1.49@1.19 Kg/mtr, middle: 100x44.45x2.0@1.603Kg/mtr)))) For shutters of doors , windows & ventilators including providing and fixing of hinges/ pivots and making provision for fixing of fittings wherever required including the cost of PVC/neoprene gasket required

Providing non asbestos high impact polypropylene reinforced cement 6mm thick corrugated sheets (as per IS 14871) roofing upto any pitch and fixing with polymer coated J or L hooks bolts and nuts 8mm dia GI plain and bitumen washer or with self drilling fastener and EPDM washers etc complete excluding the cost of purlins rafters and trusses corrugated sheets and including cutting to size and shape wherever required.

Providing and fixing of 6mm thick poly carbonate sheet roofingup to any pitch including fixing with polymer coated J or L hooks bolts and nuts 8mm dia G.I plain /Bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. the sheets shall be manufactured out of poly carbonate sheet and polymer with Ultra -Violet stabiliser in resin system under approximately 2400 psi and hot cured,. they shall be of uniform pigmentation and thickness with out air pockets and shall conform to IS 14443: 1997 , the sheets shall be clear or pigmented, textured or smooth as specified. complete as per direction of Engineer in charge. (measurement done on Sq.m all materials and labour supplied by the agency. 6mm thick Flat

Earthwork in excavation by mechanical means (Hydraulic excavator)/manual means in foundation trenchs or drains (Exceeding 30Cm in depth 1.5m in width as well as 10 Sq.M on Plan) including dressing of sides and ramming of bottoms including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50Mtr. (All kinds of Soil)

Supplying and filling in plinth with river sand under floors including watering ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. Cement concrete in 1:2:4 (1 Cement : 2 sand:4 Coarse Aggregate 20mm Down)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. Cement concrete in 1:4:8 (1 Cement : 4 sand:8 Coarse Aggregate 40mm Down)

Brick work with Flyash cement bricks of class designation 75 in Super structure above plinth levell upto V floor level in all shapes and size in Cement mortar 1:6 (1cement: 6 sand) complete in all respect as per direction of Engineer in charge

Providing wood work in framed of doors Windows, clearstorey windows and other frames , wrought framed and fixed in position: Second class teak wood

Providing wood work in framed of doors Windows, clearstorey windows and other frames , wrought framed and fixed in position: Sal Wood

cement concrete flooring 1:2:4 (1 cement : 2 sand: 4 coarse aggregate) finished with a floating coat of neat cement including cement slurry , but excluding the cost of nosing of steps etc. complete 40mm thick with 20mmm nominal size stone aggregate

providing and laying machine cut, mirror polished granite stone flooring in required design pattern (simple geometrical, abstract etc) and in patterns in combination with granite stones of different colour shades and finished surface textures etc in linear portion of the buildings all complete as per architectural drawings with 18mm thick stone slab laid over 20mmthick base of cement mortar 1:4 (1 cement: 4 sand) laid and jointed with white cement slurry @4.4 Kg/S q.Mincluding pointing with white cement slurry admixed with pigment to match the marble shade including rubbing curing and polishing etc all complete as specified and as directed by the Engineer in charge a 18mm granite stone (white, grey, ruby ,red, black etc of approved colour

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repair to scratches etc complete

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: One or more coat over old Work

Finishing wall with acrylic smooth exterior paint of required shade: New work (two or more coat applied @1.67kg/10 Sq.M) on existing cement paint

Demolishing brickwork manually/ by mechanical means including stacking of servicable materials and disposal of unservicable materials with in 50mtr lead as per direction of Engineer in Charge

Dismantling R.C.C. work, including stacking of steel bars and disposal of unservicable amterials within 50mtr lead as per direction of Engineer incharge.

Dismantling doors windows and clearstorey windows (steelor wood shutter )including chowkaths architrave holdfasts etc. complete and stacking within 50mtr lead" Of area 3 Sq.M and below

Providing and fixing factory made UPVC door frame made of UPVC extruded , section having an overall dimension , as below (tolerence +/- 1mm) with wall thickness 2.0 +/- 0.2mm. Corners of the door frame to be jointed with galvanized brackets and stainless steel screws, jointed and mitred and plastic wilded. the hinge side vericalof the frames reinforced by galvanised m.S tube of size 19x19mm and 1mm +/- 0.1 mm wall thick ness and 3 nos stainless steel hinges fixed to the frame complete aas per manufacture specification and direction of Engineer in charge. Extruded section Profile size 42x50mm

Dismantling tile work in floors laid in cement mortar including stacking materials within 50mtr lead. For thickness of tile above 10mm and upto 25mm

Dismantling cement asbestos, celotax or other hard board ceiling or partition walls including stacking of servicable materials and disposal of unservicable materials within 50mtr lead. Thickness upto 50mm thick

Providing and fixing of kitchen sink with C.I brackets, CP brass chain with rubber plug, 40mm CP brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: including clamps and fixtures complete as per direction of Engineer in charge. White glazed fire clay kitchen sink of size 600x450x250mm

Supplying and fixing and fittins of uPVC pipes of approved brand (Astral/Finolex/Supreme) 2.5Kg/Sq.Cm complete with fittings including cutting and making good the walls etc. as per direction of Engineerin Charge. 78mm dia pipes

Supplying and fixing and fittins of uPVC pipes of approved brand (Astral/Finolex/Supreme) 2.5Kg/Sq.Cm complete with fittings including cutting and making good the walls etc. as per direction of Engineerin Charge. 52mm dia pipes

Providing and fixing of chlorinated polyvinyl chloride (CPVC)pipes , having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes fittings with one CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge(Internal work exposed on Wall) (ASTRAL/ FINOLEX/equivalent) 15mm nominal bore

Providing and fixing of chlorinated polyvinyl chloride (CPVC)pipes , having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00m spacing . This includes jointing of pipes fittings with one CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge(Internal work exposed on Wall) (ASTRAL/ FINOLEX/equivalent) 20mm nominal bore

Providing and fixing of CP Brass Fittings conforming to IS 8931as per approved quality and direction of Engineer in Charge. (JAGUAR/PLUMBER/JOHNSON Equivalent. 15mm dia Bib cock

Providing and fixing of CP Brass Fittings conforming to IS 8931as per approved quality and direction of Engineer in Charge. (JAGUAR/PLUMBER/JOHNSON Equivalent. 15mm dia Stop cock

Providing and fixing of unplasticised PVC connection pipe with brass unions as per approved quality and direction of Engineer in Charge. 15mm 30CM length

Taking out the doors and window shutters and refixing them including screws as may be required. Including Cost of repairing of old door shutter of any size as per requirement along with refixing old fittings such as tower bolt, sliding door bolt, handles, (new fittings to be paid separately) with new hinges including painting the new portion with synthetic enamel paint of required shade with one coat of wood primer(cost of wood to be paid separately) including fixing in existing opening complete (Any size of any thickness)as per direction of Engineer in Charge.