National Institute Of Science Education And Research Tender

Providing and fixing factory made W.P.C. door frame of size 125x60 mm made out of solid WPC, mitred at corners. The door frame to be fixed to the wall using anchor bolt of Hilti or equivalent make of monimum 125 mm length and 10 mm dia used for brick wall/RCC wall, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges, handle, locking arrangement, vision pannels, aldrop, tower blot etc with necessary screws

Providing and fixing antistatic false flooring system for conference room: SPECIFICATIONS FALSE FLOOR: The system should be of nominal 600mm x 600mm (30mm thick) modular panels with heavy-duty pedestals. The total system weight shall not exceed 40 kg/sq.m. The system shall be able to withstand a UDL of 2000 kg/m2 (1117Kg/Sq.mt) and a point load of 450 kg/in2. PANEL: Panels shall be made of steel with an infill of lightweight, non combustible having fire resistance, thermal insulation, and flame resistance properties at 60 min cementitious material. The bottom of the panel shall be embossed in hemispherical shape to give strength and flexural rigidity. The infill material shall not become loose when the panels are cut. Panel should be able to withstand an ultimate load of at least 2.5 (3.00) times the designed point load. The entire panel shall be coated with epoxy powder coating of 75-100 microns on the exposed surface. The panel top & bottom sheet shall be 0.9/0.7mm (0.7/0.6mm) resp. Flatness should be 0.2mm. The panels shall have a top covering of anti-static high pressure laminate with resistance of 2x105 – 5x108 ohms. The HPL thickness shall not be less than 1.5mm.(1.6mm). PEDESTAL: Pedestal base shall be square of 100mm x 100mm x 2mm bearing area and assemble to a tube of 22mm dia with 2mm wall thickness. The pedestal head should not be less than 3mm thick. The pedestals should be able to accept an axial load of 22,500N and an ultimate load not less than 45,000N. Pedestal head shall be galvanized die-cut steel welded to a counter locking leveling nut. The pedestal head shall be provided with PVC cap for acoustic dampening. Height of pedestal shall be approximate 300 mm for floor /150mm for steps. STRINGER: Stringer shall be 20mm x 30mm x 1.5mm thick (25mm x 25mm x 1mm) galvanized steel hollow pipe capable of supporting a 205kg point load at the center of the stringer. Stringers shall be individual and rigidly fastened to the pedestals with 6.35mm (1/4”) fasteners.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement/epoxy & matching pigments etc. complete as approved by the EIC. Size of Tile 130x800 mm

Providing and fixing 4 mm thick veener cladding of different pattern approved by EIC with melamine polishing over 12 mm thick ply of century/green. The support for 12 mm thick ply is to be fixed with 19 mm thick 100 mm wide ply wood batten. The anchoring should be 600 mm C/C.

Supply and Installation of Anutone 25 mm thick subtex Hush square edge glass fiber core ceiling tile of size 600 x 1200 mm having density 100 Kgs/ m3, weight - 2.5 - 3 kg/m2 , installed by using impaling clip. The Impaling clips are screw fixed to directly to the frames work with the points extending outward. The spikes are tipped with stick 7 adhesive . Then the panels are positioned & press into place. The technical parameters of the subtex Hush are with core glass fiber , Fire - Class 1 & P , Acoustic - NRC up to 0.9 ,Climate ( OC RH ) - 40 & 90 , Termite Resistance - Yes Light Reflection - Yes , Light reflectance - Colour Dependent , Green (RC % ) - 25 , Hygiene ( Voc , Clean Room ) - Low , Class 3 to be fixed with impanel clips which were fixed with Philips head screw to GI frames as per the specification for fixing concealed grid wall paneling system. The concealed Anuton wall paneling system shall include GI Wall channel(WC 25) having thickness 0.45 mm, length 3600 mm, unequal flanges of 15 & 20 mm and web of 25 mm should be fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300 mm centers. Then fixed Main channels(MC 45) having thickness 0.9 mm, length 3600 mm, equal flanges of 15 mm and web 45 mm from the side wall & fixed at every 1200 mm centers with GI cross channel(CC 25) having thickness 0.45 mm, length 3600 mm, knurled web 35 mm, depth of 25 mm and equal flanges 9.5 mm is fastened to the Main channel in the direction perpendicular to the Main Channel at every 600 mm centers. The framework will maintain 50 / 75 mm gap from the walls. Now cladding the panels on the CC 25 with the help of Anatone impanel clips to get a flush groove finish. Test certificate of the use products shall be submitted after procurement of materials.

Providing and applying "RENOVA" synthetic plaster finish by approved manufacture over plastered surface by applying two coats Renovo ASP by trowel and applying two coats finish of approved colour and shade on specified locations internal/external surface in plane, curved/ any geometric shape as recommended by approved manufacturer, to perfect line, level, plumb including finishing with sharp edge at corners, nitches etc.all as per manufacturer's recommendations including all labour materials, scaffolding, double height staging if required and surface preparation etc.all complete at all heights,leads, location and lifts as specified in drawing and as directed by the Engineer in Charge

Providing, fixing of WPC board with 25 mm thick for vertical portion or rise of steps. The WPC board will be fixed with false flooring sections/ply wood battens with the help of screw @ 300 mm C/c as per direction of EIC.

Supplying and Fixing of broadloom carpet of Approved MAKE ,100% Nylon Cut Pile, Chromojet Printed, Height 8 mm (± 1 mm),Total Height 11 mm (± 1 mm),Stitch / 10 cm 41-43 (± 2% ), Pile Weight Net less Than 1000 GSM (± 5% ), Total Weight 1991 GSM (± 5% ), Secondry Backing PP Mesh, Gauge 1/8 Cut Pile, Latex Natural Rubber, Color fastness to LightTest Method: AATCC 16 (20 AFU) ≥ 4.0 at 80 Hours , Static Electricity Test Method: AATCC 134 Less than 3.5 KV, Hexapod test Method: ASTM D 5252 ≥ 4, Flammability (Radiant Panel) Test Method: ASTM E 648 ≥ 0.45 (Class I) , complete as per drawing , specifications of the architect. The carpet and Underlay (min 6 mm) will be installed with standard Fevicol/Dunlop Adhesives.The flooring to be installed as per the manufacture's specification and to be installed by its authorized agency or as Approved , with minimum 5 Years warrenty from Principal for any manufacturing defects.

Supplying and fixing of Tarining room chairs Cum Table (2Seater/1 seater) with the following specifictions: A. Legs: Legs are made of MS ERW tube section (IS: 7138) of size 75x25x2 mm thick oval tube with 5 mm thick HR brackets as per IS:2062 and 2 mm thick CRCA brackets as per IS:513 welded on to the tubes. Assembly is powder coated with epoxy polyester. Leg Height varies from 705 mm to 1005 mm in pitch of 50 mm as per layout. Sturdy anchoring by anchor bolts on to base of 8 mm thick plate for proper resting of leg. Shoe made of ultramid-Nylon are provided at the bottom for covering the base plate. B. Side Clads: Two side clads made of 18 mm thick plate with 0.8 mm thick PVC lipping and on the outside covered with welded metal structure made of 2 mm thick CRCA as per IS:513 powder coated with epoxy polyester. C. Worktop: Worktop are made of 25 mm thick prelaminated board of EI-P2 grade and approved shade conforming to IS: 12823-1990. All the edges of work surface are provided with machine pressed 2 mm thick pvc edge band glued with hot melt glue. D. Seat: Seat has self closing mechanism which will operate by means of dead weight. Seat understructure is made from combination of welded fabricated structure of 5 mm thick HR as per IS:2062 and 8 mm thick ply as per IS:303 with moulded PU foam of density 55 Kg/Cum on top which in turn is covered with stiched upholstery made of leatherite as per INT/DSN/MSS/UPH/038 of foam back fabric as per INT/DSN/MSS/UPH/013. Seat ammebmly is covered on bottom side by means of seat cover made of pp. E. Seat Back: is made from combination of 8 mm thick ply as per IS:303 with moulded foam on top which in turn is covered with stiched upholstery made leatherite as per INT/DSN/MSS/UPH/038 of foam back fabric as per INT/DSN/MSS/UPH/013. F. Seat Support frame: is made from combination of MS ERW tube section (IS:7138) of size 80x40x2.5 mm thick recatngualr tube and MS ERW tube section (IS: 7138) of size 48x19x2 mm thick oval tube welded together. Assembly os powder coated with epoxy polyester. CAP made of ultramid are provided from front to cover the oval tubes. G. Modesty: is made of 25 mm thick pre-laminated twin board of EI-P2 grade and approved shade conforming to IS:12823-1990. All the edge of modesty are provided with machine pressed 2 mm thick pvc edge band glue with hot melt glue. Dimmension: Desk Height: 730-1030mm. Desk Depth: 400/450 mm. Seat Height: 450 mm. Seat Depth: 420mm. Seat Width: 450mm. Backrest width: 450mm. Backrest Height: 430mm. For more details refer to NIT.

Providing and fixing two way bib-cock of Jaquar make DRC-37041 with complete as per direction of EIC

Providing and fixing Pillar-cock of Jaquar make DRC-37021 with complete as per direction of EIC

Providing and fixing ALD-573 Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook Jaquar make with complete as per direction of EIC

Providing and fixing VGP-81053 Angular Stop Cock with Wall Flange Jaquar make with complete as per direction of EIC

Providing and fixing wash basin JADE Italian Collection Size : 60 x 46 x 15 cm Cat. No.: 91044 pastel Hindware make, connecting pipes with complete as per direction of EIC

Providing and fixing CONCEALO (80MM) Italian Collection Size : 46 x 45 x 8 cm with cover plate Matt Finish loop Hindware make with complete as per direction of EIC

Providing and fixing ALD-769, L300x190 Bottle Trap (with Internal Partition) 32mm Size with 300mm & 190mm Long Wall Connection Pipes & Wall Flange Jaquar make with complete as per direction of EIC

Providing and fixing ALD-805B 450mm Long Braided Hose with Two/one 15mm Nuts & Rubber Washers Without/with Nipple (Suitable for Geysers/wash basin) Jaquar make with complete as per direction of EIC

Providing and fixing ACN-1137N Soap Dispenser with Metallic Bottle Jaquar make with complete as per direction of EIC

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble. Area of slab over 0.50 sqm