Forest Environment And Climate Change Department Tender

Fly ash brick masonry in cement mortar (1:6) using 25x12x8cm size bricks after immersing the bricks for six hours in water before use in Foundation and Plinth including, splays cutting, circular moulding and carbelling, champhering and similar such type of works watering, curing etc. all complete including cost, conveyance, royalties of all materials and cost of all labour, and T&P required for the work etc. complete (Crushing strength of bricks should not be less than 75kg to 99 kg/cm2 with dimensional tolerance +3%/8%)

R.C.C. (1:2:4) ........... having a minimum compressive strength ( in work test) 150 kg/cm2 cubes at 28 days after mixing and tests conducted in accordance with I.S. 456 and I.S. 516 using 12mm to 20mm size black hard crusher broken granite chips of approved quality and from approved quarry (20mm size not to exceed 25%) including hoisting, lowering, laying, compacting concrete watering and curing for 28 days centering, shuttering, finishing the exposed surface smooth, providing grooves or beads where necessary, as directed including cost, conveyance, royalties and taxes of all materials and cost of all labour T&P required for the work etc. complete in all respect but excluding the cost of M.S. roads or Tor steel and binding wire and labour charges for bending binding and tying the grills A)Column Base

B)Gade beam

C) Column

D) Lintel bend

E)Chajja

F) Roof Slab

Cutting, straightening the bent up M.S. Rods or Tor steel, bending, binding, welding joining if necessary and tying the grills and placing in position as required for R.C.C. works and for providing required no of fan hooks hoisting, lowering, laying including, cost, conveyance of all M.S. rods or Tor steel and binding wires of 18 to 20 gauge required for the work bending, binding and tying the grills in all floors (Payment will be made on weight of M.S. Rods or Tor steel only and no separate payment will be made towards the weight of binding wires)

Fly ash brick masonry in cement mortar (1:6) using 25x12x8cm size bricks after immersing the bricks for six hours in water before use in Superstructure including, splays cutting, circular moulding and carbelling, champhering and similar such type of works watering, curing etc. all complete including cost, conveyance, royalties of all materials and cost of all labour, and T&P required for the work etc. complete (Crushing strength of bricks should not be less than 75kg to 99 kg/cm2 with dimensional tolerance +3%/8%)

12mm (½") thick cement plaster (1:6) over brick masonary finished smooth, after racking out the joints including watering and curing etc. with cost, conveyance, royalities of all materials and cost of all labour and T&P required for the work etc. complete as per direction of the Engineer-in-charge

16mm (5/8") thick cement plaster (1:6) over brick masonry finished smooth, after racking out the joints including watering and curing etc. with cost, conveyance, royalties of all materials and cost of all labour and T&P required for the work etc. complete as per direction of the Engineer-in-charge

6mm thick cement plaster (1:4) over ceilling plaster finished smooth after chipping, chiselling & cleaning including watering, curing etc. with cost, conveyance, royality and taxes of all materials, labour, T&P required for the work etc. complete

12mm (½") thick cement plaster (1:4) with neat cement punning and bitumen painting on top of walls finished smooth, after racking out the joints including watering and curing etc. with cost, conveyance, royalities of all materials and cost of all labour and T&P required for the work etc. complete

Supplying, fitting and fixing of Vetrified floor tile in floor treads or steps and landing on 20mm thick bed of cement mortar (1:4) jointed with neat cement slurry mixed with pigments using white cement in grating to match the shade of the tile etc. including cost, conveyance, royalties of all materials and labour, T&P required for the work etc. complete as directed by the Engineer-in-charge

Supplying, fitting & fixing vetrified tile in dado skirting 12mm thick cement plaster (1:3:) jointed with neat cement slurry mixed with pigment using white cement in grating to match the shade of tiles including rubbing & polishing etc with cost, conveyance, royalities of all materials and cost of all labour, T&P required for the work etc. complete as directed by the Engineer-in-charge

Supplying, fitting and fixing of Granite tile flooring on floor treads or steps and landing on 25mm thick bed of Cement mortar (1:1) jointed with neat cement slurry mixed wiht pigment using white cement in grating to match the shade of marbles incluidng rubbing & polishing etc. with cost, conveyance, of all materials and cost of all labour, T&P. required for the work etc. complete as directed by the Engineer-in-charge

Supplying, fitting and fixing of ceramic Glazed in floor treads or steps and landing on 25mm thick bed of cement mortar (1:4) jointed with neat cement slurry mixed with pigments using white cement in grating to match the shade of the tile etc. including cost, conveyance, royalties of all materials and labour, T&P required for the work etc. complete as directed by the Engineer-in-charge

Supplying, fitting and fixing ceramic glazed tile in dado & skriting on 12mm thick bed of cement mortar (1:3) jointed with neat cement slurry mixed with pigments using white cement in grating to match the shade of the tile etc. including cost, conveyance, royalties of all materials and labour, T&P required for the work etc. complete as directed by the Engineer-in-charge

sandwich composite door shutter of 32mm thick, laminated with two GRP skins with wood grain finish, fabricated using UV-stabilized Isopthalic Gelcoat and one layer of 450 gsm. E-glass Chopped Strand Mat (CSM) impregnated with crthopthalic, pclyester resin. The thickness of the skins shall not be less than 1.5mm, Expanded Polystyrene (EPS structural foam panel of 29mm thickness and a density of 20 kg /Cu. mtr. shall be used as core material. Wooden reinforcements made of seasoned sal wood block of cross section not less than 28mm x 32mm and also necessary sal wood reinforcements for fixing the metal fittings such as tower bolts, aldrops, handles etc. shall be provided. A structural adhesive compatible with (EPS) foam shall be used for bending the core material, the sal wood reinforcements and the skins. The materials and process for manufacturing the door shutters shall confirm to RV-TIFAC composites Design Centre's shandards and specifications and the door shutters tested in confirmation to IS 4020-1998. The finish of door shutter will be plain colour white/ Ivory/Beige/ Light grey/ Mahogany/ Teak wood or any other colour using high quality pigments. Three heavy weight mild steel, but hinges type-I (ISI marked) size 100mm are to be fitted on one side of shutter

Providing factory made FRP (alternately called GRP) Door frame of size 75mm x 100mm, fabricated using E-Glass chopped strand Mat (CSM), U.V. stabolized Isopthalic Gelcoat and impregnated with Isophthalic resin The thickness of the GRP skin shall not be less than 2.0mm. The door frame consist of four segments, lwhich are provided with plug-in-socket arrangement in-situ in the mould. The segments are plugged in and are joined together by means of screw. The GRP frame shall be provided with wooden reinforcement on six location for high screw holding capacity for fixing metalic hold fast and shall be consolidated by filling with medium density foam/plaster of paris with fibre reinforcement. Six numbers of 260mm x 25mm x 5mm size 'S' shaped M.S. flat hold fast shall be provided with the frame. The material and process for manufacturing the door frame shall confirm to RV-TIFAC composites Design Centre's shandards and specifications. The finish of door frame will be approved plain colour using high quality pigments

Supplying, fitting and fixing window M.S. grills, grill gates made of M.S. flat/square bar of approved specification design fitted & fixed including cutting the grooves in brick or RCC structure and making good to the damages with C.C. (1:2:4), cost of nails, screws but including cost of grills, conveyance of all materials, labour, T&P. etc. complete as per direction of the Engineer-in-charge

Providing fitting and fixing M.S. pannel shutters for doors & windows as per specification and design including cutting grooves, in brick or RCC structure and making good to the damages with C.C. (1:2:4) including welding, cutting, cost, conveyance of all materials, cost of all labour, T&P required for the work etc. complete

Providing fitting and fixing M.S. pannel shutters for doors & windows as per specification and design including cutting grooves, in brick or RCC structure and making good to the damages with C.C. (1:2:4) including welding, cutting, cost, conveyance of all materials, cost of all labour, T&P required for the work etc. complete

Finishing wall surface of Wall with Acrylic Wall Putty (Water Based)

Painting two coats with paints of approved shade in all floors to wood and iron works including sand papering, polishing the surface, cost, conveyance of all materials, all labour and T&P. required for the work including the cost of paint as per the direction of the Engineer-in-charge

Distempering two coats with any approved shade over interior surface of walls and ceiling including labour, T&P. and cost of distemper required for the work etc. complete as per direction of Engineer-in-charge

Finishing wall with water proofing cement paint of approved shade two coats to give on even shade including cost of cement paint, all labour, T&P. and curing etc. complete as per direction of Engineer-in-charge

E.I LS

Sanitary Fitting LS