Directorate Of Ports And Inland Water Transport Tender

Shifting and setting up piling equipments required for piling work at each piling location, including all labour, labour cess, materials, fuel, tools & equipments etc.required to complete in all respect as per direction of Engineer-in-Charge ( No payment will be made for 1st pile )

Boring for the piles to the required depth through all types of soil strata including hard rock if any up to the founding level and stacking the bored soil at convenient place and transport to dispose the same at low lying area outside the working area with cleaning & washing the bore including cost of bentonite solution, labour, labour cess, tools, equipments, required to complete in all respect as per direction of the Engineer’-in-charge. Note:- 01. If the boring tool encounters rock at an elevation higher than the termination level of the pile indicated in the drawing then the boring shall be continued one metre into the rock from where the boring tool encounters rock first. 02. In case the soil stratum at the founding level is loose the Engineer or his representative may direct the contractor to carryout additional length of boring and payment for such additional work shall also be made under this item. 03. The sample of bored materials at regular interval shall be collect and produce for the verification of the Engineer or his representative at no extra cost. In the event of any dispute about the type of strata bored, the samples so collected shall be referred to an authorised laboratory / agency indentified by the Engineer and the decision of such authorised laboratory / agency is final and binding on both the parties. However the cost of such testing shall be borne by the contractor.

Supplying, fabricating and providing Mild steel cylindrical liners as per required thick with shoe to the required depth including providing additional stiffener plates of 6mm thick & 500 mm high including cutting, bending, welding, transporting, alignment, placing in position and driving to required depth with all labour, labour cess, materials, tools, equipments etc. complete in all respect as per direction of Engineer-in-Charge.. Note:- The stiffener shall be measured under this item. In case the soil strata found to be not good in the founding level, extra depth of liner may be provided as per site condition and measurement will be made to this effect.

Supplying, fabricating and placing of HYSD (FE-415) /(FE-500) grade steel for pile cage including cutting , bending, binding & welding and laying in position with cost, conveyance, taxes of HYSD steel and binding wires 18 to 20 gauge with all labour,labour cess, T&P, cage lowering, equipments etc., complete in all respect as directed by the Engineer in charge. (Brand of Steel - SAIL ) Measurement of reinforcement will be made on lengthwise including hooks, if any, separately for different diameter as actually used in work, excluding overlaps, from the length so measured, the weight of reinforcement shall be calcuted in tonnes by multiplying the coefficient per unit length of bar as per code of the respective size of bars used on the basis of wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding & placing shall not be measured as the cost of these items has already been included in the analysis of rates for reinforcement as per rule in force .

(A) ABOVE WATER (Reinforcement in pile shafts )

(B) UNDER WATER (Reinforcement in pile shafts)

Providing and placing designed mix cast-in-situ RCC M-30 using 20 mm down graded black hard granite crusher broken chips for piles using tremmie method up to cut off level underneath the bentonite slurry including all sampling, testing and records with watering and laying as per IS codes 456 and 516. including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge. Note: Supply, fabrication of steel reinforcement shall be measured and paid under relevant item (Rate shall include the cost of providing additional concrete above the cut-off level)

A) Above Water Piles

B) Under Water Piles

Cutting and dressing pile heads to required line and level and /or as directed and stacking the debris at convenient place and transport the same to any low lying area outside the working area and all associated cleaning of projecting reinforcements including all labour, labour cess, materials, tools, equipments etc., complete in all respect as per direction of the Engineer’-in-charge.

SECTION-B Providing and placing Designed Mix cast-in-situ concrete of grade M-30 using 20 mm down graded black hard granite crusher broken chips for pile muff and columns, Beams including watering and laying as per IS codes 456 and 516 including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge. Note: Supply, fabrication of steel reinforcement shall be measured and paid under relevant item (Rate shall include the cost of providing additional concrete above the cut-off level)

(A) ABOVE WATER (Pile muff, Main Jetty, Beams, columns, Roof slab,App. Road)

(B) UNDER WATER (Pile muff, Main Jetty,Fender Beams, columns & parapet, slabs etc)

Supplying, fabricating and placing of HYSD (FE-415) /(FE-500) grade steel including cutting , bending, binding & welding and laying in position with cost, conveyance, taxes of HYSD steel and binding wires 18 to 20 gauge with all labour,labour cess, T&P, equipments etc., complete in all respect as directed by the Engineer in charge. (Brand of Steel - SAIL ) Measurement of reinforcement will be made on lengthwise including hooks, if any, separately for different diameter as actually used in work, excluding overlaps, from the length so measured, the weight of reinforcement shall be calculated in tonnes by multiplying the coefficient per unit length of bar as per code of the respective size of bars used on the basis of wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding & placing shall not be measured as the cost of these items has already been included in the analysis of rates for reinforcement as per rule in force .

A) ABOVE WATER ( Pile muff, Main Jetty, Beams, columns, Roof slab,App. Road)

B) UNDER WATER (Pile muff, Main Jetty,Fender Beams, columns & parapet, slabs etc)

Wearing coat of 65mm thick using cement concrete in the ratio of 1:2:4 with 12 mm size HG chips including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge.

Rigid smooth centering and shuttering for R.C.C. works including false works and dismentalling then after casting including cost, conveyance, royality, labour, Labour Cess, T&P and all other taxes etc. required to complete the work in all respect as per specification and direction of the Engineer in charge.

ABOVE WATER RCC Beam, Columns Girders & Brassmers etc.(pile muf, columns, beams, parapet, ralling, bollard)

R.C.C. Floor and Roof Slab, landing balconies projecting sun-shades and chajja upto 4.3 mtr. height. (Rcc Slab)

RCC Lintel, Sunshade etc.

R.C.C. Walls and Fins including attached pillasters (Cut off wall)

UNDER WATER R.C.C. Beam, column griders and Brassmor etc. complete.(pile muf, columns & parapets, beams etc)

R.C.C. Floor and Roof Slab, landing balconies projecting sun-shades and chajja upto 4.3 mtr. height. (Rcc Ramp & waist slab)

Brick work with Fly Ash Bricks 23cmx11cmx8cm having crushing strength not less than 75 kg/m2 with dimensional tolerence ± 2 percent in cement mortar (1:4) including cost and conveyance of all materials with all the taxes, royalty,labour, T&P required for the work etc complete in all respect as directed by the Engineer in charge:

Supplying,fitting & fixing of 2.5cm to 5cm thick RCC Jally in cement mortar in position after cutting the groove etc. complete including cost and conveyance of all materials with all the taxes, royalty,labour, T&P required for the work etc complete in all respect as directed by the Engineer in charge:

16mm thick plaster in cm (1:6) over brick masonry including cost and conveyance of all materials with all the taxes,royalty,labour, T&P required for the work etc complete in all respect as directed by the Engineer in charge:

20 mm. thick grading /decorative cement plaster over roof slab/Parapet in Cement Mortar (1:4) including cost and conveyance of all materials with all taxes, royalty, labour and T&P required for the work etc. complete in all respect as directed by the Engineer-in-Charge.

Supplying, fixing and fitting of MS Choukaths, MS Grill doors,window grills of approved design including cost of all consumables,labour, taxes etc. complete in all respect as per directions of the Engineer in charge.

Supplying fitting& fixing of Dressd seasoned Sal wood choukaths for door & windows with cost, conveyance, taxes of all material, labour,labour cess, T&P etc reqd. to complete the work in all respect as directed by the Engineer in charge.

Providing & Fixing Door/Window shutter panels with 32mm thick BWR Decorative Block Board including cost, convence, taxes of all materials, labour, T&P including cost of aluminium fittings like Tower bolt ,Aldrop, Door Stopper et complete in all respect as per directions of the Engineer in charge.

Door

Window

Fixing Marble tiles in floors,Dados,treads on steps and landing on 25mm thick bed of cement mortar 1;1 (one cement, one sand) jointed with neat white cement slurry mixed with pigment to match the shade of the marbles including rubbing,polishing complete including cost and conveyance of all materials and all taxes etc. complete in ll respect as per direction of Engineer in charge.

Finishing walls with water proofing cement paint of approved shade in new work two coats to give an even shade including cost of paint

Priming one coat with any approved primer including cost of paint ( For Steel work) including all taxes , all labour, labour cess, materials, tools, equipments, fuel etc., complete in all respect as per direction of Engineer in charge.

Painting two coats with approved paint over a coat of primer including cost of all materials,cleaning, brushes, putty etc including all taxes , all labour, labour cess, materials, tools, equipments, fuel etc., complete in all respect..as per direction of Engineer in charge.

Earth work in excavation of foundation in ordinary soil with 50m initial lead and 1.5m initial lift including all taxes , all labour, labour cess, materials, tools, equipments, fuel etc., complete in all respect..as per direction of Engineer in charge.

Filling in foundation and plinth with sand from approved quarry with all leads, lifts and delifts including cost, conveyance, royality, taxes etc. complete in all respect as per specification and direction of the Engineer in charge.

Quarrying,collecting, conveying, supplying and spreading good quality laterite moorum and consolidation with HRR including watering with cost, conveyancy, royality and all taxes , labour, labour cess etc. complete as per direction of Engineer-in-Charge.

Cement concrete (1:3:6) with 40mm size broken hard granite metal including hoisting and laying with all leads, lifts and delifts etc. including watering, cost, conveyance, royality and all taxes, labour, labour cess, complete in all respect as per specification and direction of the Engineer in charge.